IB51866122
HLS Series Instructions

Packaging Contents

B. (2)

8-32 x 1 in. FH (100 deg) bracket screws

(2) vis de support de fixation no 8-32 de 2,5 cm (1 po)
(2) tornillos n.º 8-32 x 1 in (2,5 cm) de soporte C. (3) Wire Nuts
D. (1) Adpater bracket
E. (2) Extension Springs F. (1) Edison adapter

ITEMS REQUIRED

(Purchase separately)

• 2 Philips Screwdriver

• Ladder
• Gloves
• Safety Glasses

IMPORTANT SAFETY INSTRUCTIONS

Read and follow these instructions and heed all warnings, including those on the product. Failure to do so may result in serious bodily injury or property damage.
When using product, basic precautions should always be followed, including the following:

• Read and follow these instructions.
• HALO ® recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL. Before attempting installation of any recessed lighting luminaire check your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting.
• SAVE THESE INSTRUCTIONS AND WARNINGS.

WARNING
Risk of Fire – MINIMUM 75°C SUPPLY CONDUCTORS.
If uncertain, consult an electrician.
Risk of Electric Shock –
To avoid possible electrical shock, besure that power supply is turned off at fuse box or circuit breaker before installing or servicing luminaire.
of luminaires electrical systems.
Risk of Fire/Electric Shock –
If not qualified, do not attempt installation. Contact a qualified electrician. Luminaire wiring and electrical parts may be damaged when drilling for installation. Check for enclosed wiring and components.

• Install only in areas that have the construction features shown in the photographs and/or drawings.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

CAUTION

Edges may be Sharp –
Wear gloves while handling.

• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
• Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
• The HLS is wet location listed for covered ceilings only. Acceptable installations would be inside a home, building or on a porch with a roof.
• Only those open holes indicated in the photographs and / or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.
• Please examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
• This device is not intended for use with emergency exits.
• The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical installations.

DIMMING

Halo HLS is designed for dimming with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. Dimming capability may be enhanced with select dimmers that feature low end trim adjustment. (Consult dimmer manufacturer for specific load compatibility and application information.
Note some dimmers require a neutral in the wallbox.) For the latest Halo HLS product information, please refer to specifications online at www.cooperlighting.com.
WARNING
Risk of Electric Shock –
To avoid possible electrical shock, be sure that power supply is turned off at fuse box or circuit breaker before installing or servicing luminaire.

ELECTRICAL JUNCTION BOXES

Mounting to recessed mounted standard junction boxes
NOTE: The module installs onto many standard recessed ceiling and wall mounted junction boxes (Fig. 1).
– 4” octagon
– 4” square
– 4” round
– 3-1/2” round new work
– 3-1/2” round old work
(Box types and site condition vary. Installer to ensure compatibility at fit, wiring and proper mounting.)
Fig. 1

MOUNTING INTO JUNCTION BOXES

1. Use the provided wire nuts (C) to connect the supply leads inside the junction box to the luminaire.
2. Bundle any excess length of wire inside the junction box in preparation for installation.
3. Twist off the lens of the luminaire by rotating it counter clockwise. (Fig. 2)
4. Secure the luminaire to the Junction Box using #8-32 PH screws (B) through the appropriate slots (depending on the manufacturer/size of jbox being used). (Fig. 3)
5. Replace the lens back onto the luminaire. Align tabs of lens to slots in luminaire and rotate clockwise. (Fig. 4)

MOUNTING INTO JUNCTION BOXES W/ ADAPTER BRACKET

1. Secure the adapter bracket to the Junction Box using the provided #8-32 x 1in FH bracket screws (B) through the appropriate countersunk slot. (Depending on the manufacturer/size of junction box being used). (Fig. 5)
2. Install a pair of provided #8-32 PH screw (B) onto the adapter bracket, utilizing the appropriate length screw based on junction box depth/clearance.
3. Use the provided wire nuts to connect the supply leads inside the junction box to the luminaire.
4. Bundle any excess length of wire inside the junction box in preparation for installation.
5. Twist off the lens of the luminaire by rotating it counter clockwise. (Fig. 2)
6. Secure the luminaire to the Junction Box using #8-32 PH screws (B) through the luminaire’s slots. (Fig. 5)
7. Replace the lens back onto the luminaire. Align tabs of lens to slots in luminaire and rotate clockwise. (Fig. 4)

MOUNTING INTO RECESSED HOUSINGS W/ EXTENSION SPRING

1. Twist off the lens of the luminaire by rotating it counterclockwise. (Fig.2)
2. Secure the adapter bracket (D) to the HLS luminaire using the provided (B) #8-32 x 1in FH bracket screws through the appropriate countersunk slot. (Fig. 6)
3. Attach a pair of provided Springs (E) to the keyhole slots inside the housing (Fig. 7a). For 4in Housing, attach the springs into Edison socket cutouts. (Fig. 7b)
4. Attach the Edison adapter (F) by rotating it clockwise into Edison socket. (Fig. 8)
5. Make the connections of Edison adapter to the luminaire and place the wire nuts. (Fig. 9)
6. Pull the spring and attach into the adapter bracket (D) fixed to the luminaire. (Fig.10)
7. Slowly release HLS until it rests on the ceiling and center over housing opening.
8. Re-install the lens. Align tabs of lens to slots in luminaire and rotate clockwise. (Fig. 4)

HLS4 – works with 4-in and 5-in housings
HLS6 – works with 4-in, 5-in, and 6-in housings
HLS9 – works with 4-in, 5-in, and 6-in housings
For use with any 4, 5, or 6-inch diameter recessed luminaire constructed of steel or aluminum with an internal volume that exceeds 866.1cm 3 (52.9inch 3) in addition to those noted below:

COMPATIBLE HOUSING LIST

5-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting Solutions warrants to customers that, for a period of five years from the date of purchase, Cooper Lighting Solutions products will  be free from defects in materials and workmanship. The obligation of Cooper Lighting Solutions under this warranty is expressly limited to the provision of replacement products. This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or other proof of original purchase acceptable to Cooper Lighting Solutions is required before
warranty performance will be rendered. This warranty does not apply to Cooper Lighting Solutions products that have been altered or repaired or that have been subjected to neglect, abuse, misuse or accident (including shipping damages). This warranty does not apply to products not manufactured  y Cooper Lighting Solutions which have been supplied, installed, and/or used in conjunction with Cooper Lighting Solutions products. Damage to the product caused by replacement bulbs or corrosion or discoloration of brass components are not covered by this warranty.

LIMITATION OF LIABILITY:

IN NO EVENT SHALL COOPER LIGHTING SOLUTIONS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE LIABILITY OF COOPER LIGHTING SOLUTIONS FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED  ITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF COOPER LIGHTING SOLUTIONS PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF Cooper Lighting  Solutions PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
All returned products must be accompanied by a Return Goods Authorization Number issued by the Company and must be returned freight prepaid. Any product received without a Return Goods Authorization Number from the  ompany will be refused.
ooper Lighting Solutions is not responsible for merchandise damaged in transit.  Repaired or replaced products shall be
subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim filed with them. Reproductions of this document without prior written approval of Cooper Lighting Solutions are strictly prohibited.

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not  nstalled  nd used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  articular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.
  Any changes or modifications to this unit not exp essly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This device complies with ISED ICES Standard Canada ICES-005(B) / NMB-005 (B).

Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
Cooper Lighting Solutions is a
registered trademark.
All trademarks are property
of their respective owners.
Product availability, specifications, and compliances are subject to change without notice

References

• HALO | Cooper Lighting Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>