SecurityKey RK-WS Radio Key Instruction Manual
- June 8, 2024
- SecurityKey
Table of Contents
RADIO KEY ® Installation Instructions
SWITCHPLATE INSTALLATION DIAGRAM
MULLION INSTALLATION DIAGRAM
TYPICAL INSTALLATIONS STANDALONE READERS (RK-65K/RK65KS)
Note: Use separate power supplies for electric lock and for access control unit.
INSTALLATION STEPS FOR RK-WS, RK65KS:
- Drill holes as needed per installation diagram shown to the left.
- Feed cable through 3/4” hole.
- Attach the mounting plate to the mounting surface with the appropriate fasteners.
- Attach the housing to the mounting plate by inserting the two tabs inside the top of the housing into the two slots at the top of the mounting plate.
- Secure by installing supplied screws into the hole at the bottom of the reader.
- Connect cable per wiring diagram shown below.
INSTALLATION STEPS FOR RK-WM, RK65K:
- Drill holes as needed per installation diagram shown to the left.
- Feed cable through 3/4” hole.
- Attach reader to any flat surface with two #6 screws.
- Snap label insert into front of reader to cover screws.
WIRING CONNECTIONS
| RK-65K & RK65KS| RK-WM & RK-WS
---|---|---
WIRE
COLOR| STANDALONE WIRING
CONNECTIONS| WIEGAND OUTPUT
WIRING CONNECTIONS| WIRING CONNECTIONS
RED| 5-14 VDC +| 5-14 VDC +| 5-14 VDC +
BLACK| GROUND —| GROUND —| GROUND —
YELLOW| LATCH RELAY| NOT NEEDED| BUZZER INPUT (1)
BLUE| LATCH RELAY| NOT NEEDED| HOLD
ORANGE| REMOTE OPEN (2)| GREEN LED INPUT (3. 1)| GREEN LED INPUT (1)
BROWN| REMOTE OPEN (2)| RED LED INPUT (3. 1)| RED LED INPUT (1)
GREEN| NOT NEEDED| DATA-0| WIEGAND DATA-0
WHITE| NOT NEEDED| DATA-1| WIEGAND DATA-1
( 1 ) Connect to GROUND to activate
(2) Input Programmed for Remote Open
(3) Input Programmed for LED/Beeper Control
PARTS SUPPLIED:
Access Control Unit
MOV (RK65K & RK65KS only)
Operating Guide (RK65K & RK65KS only)
Installation Instructions all Models
Log Sheet (RK-65K only)
Mounting Plate (RK-WS, RK65KS only)
2, #6 Mounting Screws
1, 4×40 Screw (RK-WS, RK65KS only)
1, Security Screw (RK-WS, RK65KS only)
Snap-In Labels (RK65K only)
ACCESSORIES (NOT INCLUDED):
RK600-PS: 9VDC plug-in power supply.
It is designed to power the RK-65K and RK-65KS only, and requires 120 VAC
input.
RK-BB: Back Box/Spacer (RK-WS & RK65KS)
RK-HHP: Hand-Held Programmer (RK65K)
SK-SR SecuRelay™ – Smart relay module, DPDT.
SPECIFICATIONS:
POWER REQUIREMENTS
5-14 VDC, 90 mA
OUTPUTS
SPST Solid State Relay, 1A max. @60 VAC or DC
Normally open or normally closed (field programmable (See Operating Guide).
For RK-65K and RK-65KS only.
INPUTS
Default is Remote Open (requires contact closure).
For RK-65K and RK-65KS only.
Also programmable as Bicolor (Red or Green) LED Control or Buzzer/LED control
for online systems (see Operating Guide).
WIEGAND OUTPUT
Any Wiegand Format up to 40 bits
Maximum Distance: 500 ft. – 5 or 6 conductor 20 gauge shielded cable
ENVIRONMENT
Access Control Unit, Key Tags and Cards Ambient Temperature
-40° to +70°C (-40° to +158°F)
Humidity
0 to 95% (non-condensing)
INSTRUCTION TO THE USER
FCC ID: NNHRK100M
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
or the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet of a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user’s authority to operate this equipment.
CONFORMS TO UL STD. 153
CERTIFIED TO CSA STD. C22.2 NO. 12
SECURA KEY
Models: RK-WS/RK-WM
RK-65KS/RK65K
5-14 VDC, 90 mA
3321906 8136
20301 Nordhoff Street, Chatsworth, CA 91311
PHONE 818-882-0020
• FAX 818-882-7052
TOLL-FREE 800-891-0020
www.securakey.com
[email protected]