TRITON TN6210 Series Framed Rectangular Sliding Door Installation Guide

June 10, 2024
TRITON

TRITON Logo SLIDING DOOR INSTALLATION GUIDETRITON TN6210 Series Framed
Rectangular Sliding Door

Please reed these instructions carefully and keep for future reference. incorrect fitting will invalidate the guarantee.

SAFETY

  • Handle glass with great cafe. Although the glass is very tough, sharp impacts can damage both the glass and metal frame.
  • Make sure there are no hidden pipes or cables hidden in the wall where you intend to drill.
  • Wear safety goggles. shoes and appropriate clothing.

BEFORE INSTALLATION

  • Check that the shower tray is level in all directions. The enclosure will not sit correctly on an uneven surface. If uneven, the wall channels may not fit and the doors may not shut correctly.
  • The enclosure should be fitted on tiled walls which are sealed with waterproof grout.
  • There must be a good silicone seal between the dm of the shower tray and the wall.
  • The shower tray and the enclosure must match in size. Attempting to fit the incorrect size of enclosure to the shower tray will result in water leaks.
  • Always check very carefully that components are vertical.
  • To avoid damage, use the opened out packaging to build the enclosure on.

**Equipment needs* Drill. 6.0mm Masonry Bit. Crosshead PH2 Screwdriver Spirit Level. Pencil. Tape Measure. Sloane Sealant.
Note:** The BMWS and wall plugs supplied are for masavy wells. For lightweight wells i.e. stud parollon. plasterboard etc, use the correct type of axing..

FIXING KIT COMPONENTS

TRITON TN6210 Series Framed Rectangular Sliding Door -
Kit

TOOLS REQUIRED

TRITON TN6210 Series Framed Rectangular Sliding Door - Kit
1

SLIDER DOOR CODE| DOOR SIZE IN MM| OVERALL ADJUSTMENT IN RECESS MM
---|---|---
TN6210| 1000| 950-990
TN6211| 1100| 1050-1090
TN6212| 1200| 1150-1190

STAGE 1
Please ensure your tray is 100% level in all direction before fitting your enclosure.

TRITON TN6210 Series Framed Rectangular Sliding Door - Kit
2 STAGE 2
Determine your step in from the edge of the tray. Measure your X dimension. Measurement must fall within the below table of adjustments market as X. Plumb your wall profiles and mark the points of fixing.

TRITON TN6210 Series Framed Rectangular Sliding Door -
Kit3

STAGE 3
Fit your fixed panels seal to the Loosen the screw before you fit your top top and bottom of the fixed panel.
STAGE 4
Loosen the swerw before you fit you top and bottom profile to the upright profile.TRITON TN6210 Series Framed Rectangular Sliding Door -
Kit4 STAGE 5
Slot the top and bottom profile fixing screws into the slots in the upright profile.

TRITON TN6210 Series Framed Rectangular Sliding Door -
Kit4

STAGE 6

TRITON TN6210 Series Framed Rectangular Sliding Door - Kit
5

STAGE 7
Tighten Al 2S0020 onto the fixed panel to secure the glass.TRITON TN6210
Series Framed Rectangular Sliding Door - Kit6 STAGE 8
When fitting a fully framed product into a recess you must push the wall profiles on the uprights. Then lift the assmbled frame onto the tray.

TRITON TN6210 Series Framed Rectangular Sliding Door -
Kit7

STAGE 9
When the enclosure is between your two walls you can then fix your wall profiles to the walls using the fixing screws provided. Equalise the gaps on either side of the upright profiles ang fix using 2SY51TRITON TN6210 Series
Framed Rectangular Sliding Door - Kit 8 STAGE 10

TRITON TN6210 Series Framed Rectangular Sliding Door -
Kit8

STAGE 11
To fit your door panel firstly hang the top roller to support the weight of the glass panel. You can then leave your door panel hang making it easier to release your easy clean roller into the bottom track.TRITON TN6210 Series
Framed Rectangular Sliding Door - Kit9 STAGE 12

TRITON TN6210 Series Framed Rectangular Sliding Door - Ki
10

STAGE 13
You can adjust the gaps between the door panel and the closing post by turning the adjustment screw in the top roller.TRITON TN6210 Series Framed
Rectangular Sliding Door - Kit 11 STAGE 14

TRITON TN6210 Series Framed Rectangular Sliding Door - Kit
12 PARTB LIST

TRITON TN6210 Series Framed Rectangular Sliding Door - Part
List

Item No.| Part List Description| Part Code| Sliding Door Size Variations
---|---|---|---
1000| 1100| 1200
1| Top And Bottom Profile Set W1000mm| A| 2| |
1| Top And Bottom Profile Set W1100mm| A| | 2|
1| Top And Bottom Profile Set W1200mm| A| | | 2
2| Wall Profile| AO250020| 2| 2| 2
3| Screw Cover Cap| C070| 12| 12| 12
4| Round Screw 3.5•30| NO81| 8| 8| 8
5| Upright Profile| A0250022| 1| 1| 1
6| Magnet Seal| AO2S0039| 1| 1| i
7| Magnet Seal| Al2S0009| 1| 1| 1
8| Handle| SP00063| i| 1| 1
9| Moving Glass B| s| 1| 1| 1
10| Bottom Roller| D6024| 2| 2| 2
11| Fixed Glass e| c| 1| 1| 1
12| Wall Plug| 2SP12| 6| 6| 6
13| Upright Seal 12S0013 For Fixed Glass| Al250013| 1| 1| 1
14| Upright Seal 12S0015 For Moving Glass| Al2S0015| 1| 1| 1
15| Round Screw 430| 2SY51| 6| 6| 6
16| Waterproof Seal| Al2S0055| 2| 2| 2
17| Top Roller| D6025| 2| 2| 2
18| Glass Clip (Has Been Installed)| Al2S0020| 2| 2| 2
19| Round Screw 4
16| N124| 2| 2| 2

TRITON Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals