triton 15A Contractor Saw Module 10″ Instructions

triton 15A Contractor Saw Module 10" Instructions

tritontools.com

Original Instructions

Introduction

Thank you for purchasing this Triton tool. This manual contains information necessary for safe and effective operation of this product. This product has unique features and, even if you are familiar with similar products, it is necessary to read this manual carefully to ensure you fully understand the instructions. Ensure all users of the tool read and fully understand this manual.

Description of Symbols

The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use.

Specification

Due to the constant evolution of our product development, the characteristics of Triton products may change without notice.

WARNING: Always wear ear protection where the sound level exceeds 85dB(A) and limit the time of exposure if necessary. If sound levels are uncomfortable, even with ear protection, stop using the tool immediately and check the ear protection is correctly fitted and provides the correct level of sound attenuation for the level of sound produced by your tool.

WARNING: User exposure to tool vibration can result in loss of sense of touch, numbness, tingling and reduced ability to grip. Long term exposure can lead to a chronic condition. If necessary, limit the length of time exposed to vibration and use anti-vibration gloves. Do not operate the tool with hands below a normal comfortable temperature, as vibration will have a greater effect. Use the figures provided in the specification relating to vibration to calculate the duration and frequency of operating the tool.
Sound and vibration levels in the specification are determined according to international standards. The figures represent normal use for the tool in normal working conditions. A poorly maintained, incorrectly assembled, or misused tool, may produce increased levels of noise and vibration. www.osha.europa.eu provides information on sound and vibration levels in the workplace that may be useful to domestic users who use tools for long periods of time.

General & Electrical Safety

• In the event of a malfunction or breakdown, grounding provides a path of least resistance for the electric current to reduce the risk of electric shock. This tool is equipped with an electric cord with an equipment-grounding conductor and a grounding plug.
• The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
• Do not modify the plug provided ­ if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with green insulation – with or without yellow stripes – is the equipment-grounding conductor.
• If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
• Check with a qualified electrician or service personnel if the grounding instructions are not clear, or if in doubt as to whether the tool is properly grounded.
• Use only 3-wire extension cords with 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug.
• Repair or replace damaged or worn cord immediately.
  This tool is intended for use on a circuit with an outlet that resembles Figure A.

The tool has a grounding plug similar to the plug illustrated. A temporary adapter, which resembles the adapter illustrated in Fig B, may be used to connect this plug to a 2-pole receptacle if a properly grounded outlet is not available. The temporary adapter should be used only until a properly-grounded outlet can be installed by a qualified electrician. The green-colored grounding clip with metal screw extending from the adapter, must be connected to a permanent ground such as a properly-grounded outlet box.

1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and adjusting wrenches are removed from the tool before switching it on.
3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENTS. Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well illuminated.
5. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from work area.
6. MAKE THE WORKSHOP CHILD-PROOF with padlocks, master switches, or by removing starter keys.
7. DON’T FORCE THE TOOL. It will perform more efficiently and safely when working at the rate for which it was designed.
8. USE THE CORRECT TOOL. Don’t force the tool or attachment to perform a task for which it was not designed.
9. USE THE CORRECT EXTENSION CORD. Make sure the extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. The table below shows the correct size to use depending on cord length and the nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
10. WEAR CORRECT APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use a face or dust mask if the cutting operation is dusty. Everyday eyeglasses only have impact-resistant lenses; they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold work when practical. It is safer than using hands and also it frees both hands to operate tool.
13. DON’T OVERREACH. Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing, and when changing accessories, such as blades, bits, cutters etc.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in `off’ position before plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use of incorrect accessories may create a risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be the workpiece from the saw, once the blade has stopped spinning. carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.
21. NEVER LEAVE THE TOOL RUNNING UNATTENDED. SWITCH THE POWER OFF. Do not leave the tool unattended until it comes to a complete stop.

Table Saw Safety

WARNING: ALWAYS wear personal protective equipment, including but not limited to eye protection, ear defenders, a suitable dust mask and suitable gloves when using a saw table. Ensure all people in the vicinity of the work area use adequate protection. Keep bystanders a safe distance away.
WARNING: ALWAYS connect the dust extraction port on the blade guard to a suitable vacuum dust extraction system. Certain types of wood are toxic or may cause allergic reactions in people and animals, especially when exposed to very fine dust. ALWAYS wear appropriate respiratory protection in addition to vacuum dust extraction.
WARNING: The rated speed of the saw blade must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.

• a) ONLY fit circular saws that are listed as compatible in ‘Specifications’ to the saw table. ONLY use compatible saw blades, ensuring that the riving knife is not thicker than the blade kerf, and not thinner than the saw blade.
• b) ENSURE your work area is safe and sufficiently lightened, without obstructions, trip hazards or any other potential dangers.
• c) NEVER attempt to cut metals or drywall products containing masonry with this table saw. It is exclusively designed for use with wood and wood-like products.
• d) DO NOT attempt to use a molding head with this saw table. The compatible circular saws and the table setup are not suitable for this kind of cutting
• e) ALWAYS ensure the work area is well ventilated. Remove sawdust frequently and clean out sawdust from the saw, to prevent a potential fire hazard.
• f) NEVER attempt to remove wood fragments or dust from the blade with your hands whilst the blade is spinning. ALWAYS switch the saw off, disconnect the machine from the power supply, and wait until the blade has come to a standstill. ALWAYS use cut-proof gloves when touching the saw blade, to avoid injury.
• g) NEVER leave the saw running unattended. After switching off, DO NOT leave the saw table, until the blade has come to a complete stop.
• h) CAREFULLY read the instructions listed in `Kickback Prevention’, and follow these recommendations when using a saw table.
• i) ALWAYS feed the workpiece into the blade AGAINST the direction of rotation. The feed direction is indicated by the arrow moulded into the table surface.
• j) ALWAYS use the parallel fence when making rip cuts. Ensure the fence is parallel to the blade, it MUST NOT be angled towards the blade, and securely lock the fence at both ends.
• k) ALWAYS secure the workpiece firmly against the rip fence or mitre gauge. NEVER use the rip fence during the same operation as the mitre gauge.
• l) NEVER remove the blade guard or riving knife. Riving knives are also known under the term `spreaders’.
• m) ALWAYS use a push stick when ripping narrow workpieces, so your hand does not come close to the saw blade. The push stick must ALWAYS be narrower than the workpiece, to prevent the push stick from coming into contact with the blade. Use a featherboard and push blocks for non-through cuts. Store the push stick with the saw, when not in use.
• n) NEVER perform any free-hand operations, only supporting the workpiece with your hands. ALWAYS use either the rip fence or a mitre fence to position and guide the work.
• o) NEVER reach behind, over or within 75mm (3″) of the blade, with either hand, for any reason.
• p) ALWAYS move the rip fence out of the way when making cross cuts. NEVER use the rip fence as a cut-off gauge when cross cutting.
• q) NEVER attempt to free a stalled saw blade, with the saw switched on. ALWAYS switch off and disconnect the machine from the power supply.
• r) ALWAYS support large workpieces on the in-feed and out-feed sides of the saw table, and where necessary, also to the sides. Use roller supports or saw horses wherever possible.
• s) NEVER let go of the workpiece before it is pushed all the way past the saw blade, using a push stick where necessary.
• t) AVOID irregularly shaped workpieces that do not have a straight edge to guide along the rip fence.
• u) DO NOT cut round stock with table saws. DO NOT use table saws to cut logs or firewood.
• v) ALWAYS avoid awkward operations and hand positions, where a sudden slip could cause your hand or other parts of your body to come into contact with the blade.
• w) INSPECT the throat plate before use. Replace throat plates that are damaged or worn.
• x) ONLY use accessories listed in this manual, to be compatible with the saw table. The use of incompatible accessories may inherently be dangerous and lead to severe injury or property damage. ALWAYS follow all safety instructions and safe usage procedures, provided with the accessory.
• y) ALWAYS switch the saw table off before disconnecting it from the power supply. This avoids accidental starting upon reconnecting to the power supply.

Kickback Prevention

Note: Kickback occurs when the blade stalls rapidly, as a result from being pinched, bound or misaligned, and drives the workpiece is driven back towards the operator. It can also pull the operator’s hand into the blade, resulting in serious injury.

WARNING: Kickback is the result of saw misuse and/or incorrect operating procedures or conditions, however, if precautions are taken, kickback forces can be controlled by the operator, or avoided altogether:

• a) ALWAYS use the saw with the riving knife (also known as `spreader’) installed. NEVER remove the riving knife, to prevent the kerf from closing on to the blade.
• b) NEVER attempt to cut with a dull or warped blade. ALWAYS ensure the blade is suitable for the material to be cut.
• c) ALWAYS ensure the rip fence is parallel to the blade. If the fence tilts inward towards the blade, the workpiece may come into contact with the back edge of the blade, and may be thrown back towards the user uncontrollably as a result.
• d) NEVER use the rip fence and mitre gauge simultaneously. This can lead to serious kickback and severe injury.
• e) Use CAUTION when cutting large sheets. Ensure larger stock is properly supported by adequate in-feed and out-feed supports.
• f) DO NOT cut round stock or workpieces that cannot lay flat on the table. Avoid cutting twisted, distorted or knotty wood.
• g) DO NOT cut wet wood, as it produces higher friction against the saw blade. Wet sawdust can accumulate on the blade, further increasing the likelihood of kickback.
• h) ALWAYS maintain a firm grip on the workpiece, with both hands, and position your arms to resist kickback forces.
• i) Stay out of blade path and position your body to either side of the blade, but not in line with the blade. unintentionally contacted.
• j) DO NOT back out of the cut. If you have to interrupt a cut before it is complete, switch the saw off, and remove
• k) PREVENT workpieces from dropping on to the blade. DO NOT attempt to perform plunge cuts with your table saw.
• l) ALWAYS use push sticks or push block where appropriate, to guide the workpiece through the blade. Use feather boards to hold down the workpiece wherever possible

WARNING:

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated rubber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks dust extraction. that are specially designed to filter out microscopic particles.

Product Familiarisation

1. Mains Plug
2. Saw Blade
3. Blade Guard
4. Guard Bracket
5. Riving Knife
6. Guard Securing Clip
7. Anti-Kickback Securing Clip
8. Anti-Kickback Device
9. Riving Knife Locking Screw
10. Brush Cap
11. Module Levelling Bobbin
12. Module Roller
13. Dust Chute Panel
14. Blade Height Winder
15. Bevel Angle Adjuster
16. 45° Trimming Screw
17. 0° Trimming Screw
18. Bevel Angle Gauge
19. Angle Calibration Screw
20. Locking Lever
21. Thumb Holes
22. Hand Slots
23. Kerf Plate Access Hole
24. Module Levelling Bobbin Screw
25. Kerf Plate Levelling Screw
26. Kerf Plate
27. Sacrificial Plate
28. Lateral Alignment Wheel
29. Module Levelling Screw
30. Module Table Surface
31. Arbor Holder
32. Blade Securing Nut
33. Arbor
34. Blade Flange
35. Securing Knob
36. Riving Knife Adjustment Screw
37. Mounting Tab
38. Fixing Screw
39. Push-Stick
40. Multi-Tool 1
41. Multi-Tool 2
42. Protractor Gauge
43. Bench Locking Knob
44. Adjustable Front Fence
45. Supporting Bracket
46. 45° Angle Fence
47. Angle Slot
48. Graduation Scale
49. Angle Viewfinder
50. Bench Rail
51. Angle Adjustment Knob
52. Rip Fence
53. Rip Fence Arm
54. Power Inlet Box
55. Reset Button
56. Rear Bevel Angle Locking Nut

Intended Use
An effective saw table capable of mitre, bevel and cross cutting with anti- kickback device. Includes Protractor Gauge and Rip Fence. Suitable for cutting wood and wood-like materials only. For use with the Triton Workcentre TWX7 and accessories.
Avoid blade overheating

• Always check the condition of the blade prior to any cutting operations. Ensure the blade is sharp and is the correct type of blade for the material. If the blade is blunt, replace or have professionally sharpened (if applicable)
• During cutting operations, run the tool without load for 15-20 second intervals to ensure the air cools the blade
• Take extra care when cutting hardwood. Harder materials generate more resistance and more heat on the blade and motor, so ensure more frequent air cooling intervals are applied

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or damaged, have such parts replaced before attempting to use this tool

IMPORTANT: Read these instructions in combination with the instructions supplied with your Triton Workcentre. For instruction video, please go to www.tritontools.com

Before Use

WARNING: Ensure the saw table is switched off and disconnected from the power supply before attaching or changing any accessories, inserting or removing modules or making any adjustments.
WARNING: ALWAYS wear suitable cut proof gloves when handling the table saw blade. Not doing so may result in
cuts, or harm to the operator

Module levelling screw installation
• With the Contractor Saw Module on a secure flat surface, install the Module Levelling Bobbin Screws (25), Module Levelling Screws (30) and the Module Rollers (13) as depicted in Fig.A

Installing and removing the module
WARNING: When carrying the Contractor Saw Module, use the Hand Slots (23).
Note: In order to insert/remove the Contractor Saw Module, the Saw Blade (2) needs to be in the 45° position. See `Blade adjustment’ for detailed instructions regarding alteration of the blade angle.

Module installation:
WARNING: Lower the Saw Blade (2) to a safe height position before installing or removing the Contractor Saw Module.
WARNING : Some modules are heavy, especially with power tools installed. ALWAYS grip the module using the Hand Slots (23), ensuring secure footing and upright positioning. Avoid awkward movements when removing and fitting modules.

IMPORTANT: Always lower modules carefully using both the provided Thumb Holes (22). Uncontrolled lowering can cause Workcentre, module and power tool damage as well as possible injury to the operator.
WARNING: Do not place fingers and/or body parts between the module and the Workcentre chassis. See Fig. B

• Slide the Module Rollers (13) into the Module Mounting Guides and carefully lower the module into place, see Fig. B
• Toggle both Module Locks into the locked position, Fig. C

Note: Ensure the Module Levelling Bobbin Screws (25), are correctly located in the bobbin locators. The Module Levelling Screws (30) need to be adjusted to remove play between the module and the Workcentre chassis.

Module removal:

• Toggle the Module Locks into the `unlocked’ position. Lift the module from the chassis using the Finger Holes, and slide the Module Rollers (13) from the Module Mounting Tracks, see Fig. B

Levelling table modules

• Level the module by adjusting the Module Levelling Bobbin Screws (25), and Module Levelling Screws (30) in the order depicted in Fig. D
• Check the module is level with the Table Surface using a straight edge, as depicted in diagram Fig. E. If the module is still uneven, repeat the above process

Assembling the Contractor Saw Module

• Use the Figures provided; A-O combined with the information below to assemble the Contractor Saw Module.

Riving knife installation

WARNING: Ensure the Riving Knife (5) is correctly locked into place before use.

1. With the Saw Blade (2) in the 0° position, raise the blade to its maximum height using the Blade Height Winder (15)
2. Loosen the hex screw located at the infeed end of the Kerf Plate (27), and use the Kerf Plate Access Hole (24) to release the plate, Fig. F
3. Slot the Riving Knife (5) into the fixing bracket, and fasten the Securing Knob (36) Fig. G
4. The Riving Knife in through-sawing position is seen depicted in Fig. H • The Riving Knife features a secondary position for performing slot cuts:
   • Lower the Riving Knife until it locates in the fixing bracket at its lowest point and fasten the Securing Knob (36), Fig. I

Kerf plate levelling
WARNING: Ensure the Kerf Plate (27) is installed and levelled correctly before use.

1. Level the Kerf Plate by adjusting the Kerf Plate Levelling Screws (26)
2. Check the Kerf Plate is level against the surrounding Table Surface using a straight edge. If the Kerf Plate is still uneven, repeat the above process

Blade adjustment

• To adjust the bevel angle of the Saw Blade (2):
  1. Unlock the Locking Lever (21)
  2. Rotate the Bevel Angle Adjuster (16) to alter the angle of the blade
  3. Use the Bevel Angle Gauge (19) to view the blade angle

• To adjust the Saw Blade height, turn the Blade Height Winder (15):

• Anticlockwise to raise the Saw Blade

• Clockwise to lower the Saw Blade

Blade calibration
Note: Refer to Fig. J, when calibrating the Saw Blade (2).

1. Raise the Saw Blade to its maximum height using the Blade Height Winder (15)
2. Using the Bevel Angle Adjuster (16) adjust the Saw Blade so it is perpendicular to the Table Surface
3. Place a set square (not provided) flat against the Table Surface and against the blade
4. Loosen the 0° Trimming Screw (18)
5. Adjust the Saw Blade angle so it is parallel with the set square
6. Loosen the Angle Calibration Screws (20) and align the red dial with `0′ on the Bevel Angle Gauge (19)
7. Lock the Saw Blade into position using the Locking Lever (21)
8. Tighten the 0° Trimming Screw
9. Loosen the 45° Trimming Screw (17)
10. Move the Saw Blade into the 45° position
11. Tighten the 45° Trimming Screw and check 45° is displayed on the Bevel Angle Gauge. If 45° is not displayed on

Riving knife alignment

1. With the Saw Blade (2) in the 0° position, raise the blade to its maximum height using the Blade Height Winder (15)
2. Loosen the hex screw located at the infeed end of the Kerf Plate (27), and use the Kerf Plate Access Hole (24)
3. Loosen the Riving Knife Adjustment Screw (37) and the Riving Knife Locking Screw (9)
4. Place two straight edges (not provided) against the sides of the Saw Blade and the Riving Knife
5. Remove the straight edges and tighten the Riving Knife Adjustment Screw, followed by the Riving Knife Locking Screw
6. Check the Riving Knife is aligned with the Saw Blade. If the Riving Knife is not aligned, repeat steps `3-5′ until aligned
7. Replace the Kerf Plate, the Riving Knife is now aligned

Blade guard and accessory installation
Note: Refer to Fig. K, when installing the Blade Guard (3) and Anti- Kickback Device (7).
Note: Ensure the removable Blade Guard is down over the Saw Blade (2) for through-sawing cuts.

Rip fence

• nfold the Rip Fence Arms (54) and slide into the Rip Fence Guides of the Workcentre chassis, Fig. L
• The Rip Fence Arms display a graduation scale. When used in combination with the Rip Fence Position Indicator, accurate width measurements can be determined

Protractor gauge

• Loosen the Bench Locking Knob (44) and slide the Bench Rail (51) into the T-Slot of the Workcentre chassis, Fig. M
• Tighten the Bench Locking Knob to secure the Protractor Gauge (43)
• Angle adjustment can be achieved by unlocking the Angle Adjustment Knob (52) and turning the Protractor Gauge to the desired angle
• The angle is displayed through the Angle Viewfinder (50)
• Adjust the Adjustable Front Fence (45) by loosening the 2 hex bolts, to accommodate different-sized workpieces
• Turn the Protractor Gauge around and set the angle to 0° to use the 45° Angle Fence (47) for a precise 45° cut

Dust extraction
WARNING: ALWAYS use a suitable vacuum cleaner or workshop dust extraction system.
WARNING: Some dust from natural wood, surface coatings and composite materials contain toxic substances.
ALWAYS dispose of harmful dust according to laws and regulations.

• While dust extraction can be achieved using any vacuum cleaner, domestic (bag-type) units can fill up very quickly. For a much larger capacity, consider fitting a Triton Dust Collector (DCA300) to your vacuum cleaner
• The combined electrical load of the Contractor Saw and vacuum cleaner may exceed the rated amperage of the domestic extension lead or power outlet. Always connect the vacuum cleaner and Contractor Saw to separate electrical outlets, and switch on both appliances separately

Electrical connections
Note : The Workcentre features a mains isolator switch with Trailing Socket, to allow easy connectivity to power tools, Fig. N
Connect the Workcentre to the mains via the Mains Plug
• Use the Trailing Plug to connect power tools to the power supply.
1. Power tools must be connected to the Workcentre switchbox
2. If necessary, suitable extension cords may be used to extend the Workcentre’s own power cable

WARNING: Use only extension cords that are in good condition, with a sufficient cross section to carry the current the power tool will draw. Undersized extensions will cause in-line voltage to drop, resulting in power loss, overheating and burning out of the power tool motor.

Operation

WARNING: ALWAYS wear eye protection, adequate respiratory and hearing protection, as well as suitable gloves, hen working with this tool.

IMPORTANT: The Contractor Saw Module is marked with the feed direction. This indicates the correct and safest direction for the workpiece when making the cut.

WARNING: Do not over-balance the Workcentre by using very large workpieces.
WARNING: Ensure the Kerf Plate (27) is installed and levelled correctly before use.
Note: Refer to your original TWX7 Workcentre instructions for full information and diagrams that refer to parts of the Workcentre.

Workcentre switchbox operation
IMPORTANT: The switchbox requires a live mains connection to switch ‘on’. It will reset to ‘off as soon as power is disconnected and require resetting to ‘on’ when power is restored to continue operation

Switching ON & OFF

1. The Workcentre ON/OFF Switch is located at the front of the Workcentre chassis, Fig. N
2. Connect the Workcentre Mains Plug to a wall socket and switch ‘on’
3. Switch the Workcentre ON/OFF Switch into the ‘O’ position by pushing on the ‘Knee-Off’ Stop Button
4. Connect the power tool’s mains plug to the Power Tool Connection Socket
5. Switch ‘on’ the power tool by pressing the ON/OFF Switch into the ‘I’ position
   • Press down on the Knee-Off Stop Button to switch ‘OFF’

Note: If the power supply is interrupted during use, the machine will not restart. The ON/OFF Switch will need to be activated again to resume operation.

User position and feed direction

• The main user position is defined by the location of the Knee-Off Stop Button
• ALWAYS remain positioned in close proximity to the ON/OFF Switch, so the machine can be instantly switched off in the case of emergency
• Feed workpieces in the direction indicated by the arrows on the Module Table Surface (31)

Using the table extensions (available as accessories)

• The (optional) Workcentre Outfeed Support (TWX7OS) and Workcentre Side Support (TWX7SS) bars can be adjusted to provide sturdy support to larger workpieces. Adjustability can be performed by loosening the Outfeed Support Knobs, and/or the Side Support Knobs and extending the corresponding support bar to the size of the workpiece

Adjusting the protractor gauge

Note: In order to increase the life span of the Protractor Gauge (43) it is recommended that a sacrificial piece of wood should be fixed to the fence.

1. With the Protractor Gauge located in the T-Slot, loosen the Bench Locking Knob (44) and the Angle Adjustment Knob (52)
2. Adjust the angle of the Protractor Gauge, the angle is displayed through the Angle Viewfinder (50)
3. Lock the Angle Adjustment Knob securely, whilst only securing the Bench Locking Knob until resistance is felt, to secure the Protractor Gauge in the T-Slot

• Alternatively if a 45° angle is required:

1. Remove the Protractor Gauge and reinstall so the Adjustable Front Fence (45) is trailing
2. Ensure ‘0°’ is displayed through the Angle Viewfinder and lock the Angle Adjustment Knob
3. Use the 45° Angle Fence (47) to secure the workpiece

Push-stick use
WARNING: Performing cuts on small workpieces can be dangerous and will require the use of push-sticks.

• A Push-Stick (40) is included with this product. However, it may be necessary to use more than one push-stick to safely cut your workpiece
• When ripping small diameter stock it will be necessary to use multiple Push-Sticks in order to secure the work piece that is in close proximity to the Saw Blade (2)

Cutting operations
WARNING: NEVER handle the part of the workpiece that is near the Saw Blade (2) whilst the blade is in motion or whilst the power is ON. Doing so may cause the workpiece to be ejected from the machine and could cause harm to the operator.

WARNING: Keep both hands away from the blade and the cutting path at all times.
WARNING: NEVER attempt to pull the workpiece back during the cutting process; switch the machine off and wait for the Saw Blade to stop rotating before removing the part-cut specimen.
WARNING: When cutting oversized workpieces that are larger than the width and/or length of the Workcentre Table Surface, it is necessary to adequately support the workpiece using the (optional) Workcentre Outfeed Support (TWX7OS) and/or Workcentre Side Support (TWX7SS) which are available from your Triton dealer.

WARNING: Ensure the Workcentre is set up on a stable, flat, and secure surface. Before using the Workcentre ALWAYS check for stable footing. Using the Workcentre on rough, unsecure terrain is dangerous and could cause serious harm to the operator.
Performing a cross cut

WARNING: To avoid the cut-off part of the workpiece being thrown, avoid restricting the workpiece using the Rip Fence (53). Use the Protractor Gauge (43) to support the workpiece during the cutting procedure.

• If the workpiece does not fit within the maximum workpiece dimensions specified within the `Specification’, adjust the support structures to accommodate the workpiece during the cutting procedure

1. Position the Rip Fence away from the path of the workpiece. Adjust the Protractor Gauge (43) to the desired angle, and lock into position
2. Position the Saw Blade so the highest point is approximately 3.2mm higher than the top of the workpiece
3. Hold the workpiece firmly against the Protractor Gauge using the hand closest to the blade, and position the other hand on the part of the workpiece furthest from the Saw Blade for support
4. Switch the Contractor Saw ‘on’ and allow the Saw Blade to reach the operating speed
5. Whilst using both hands to support the workpiece, as described in ‘step 3’, slowly feed the workpiece into the Saw Blade

Note: Before removing the cut-off part of the workpiece, turn the saw ‘off’ and wait for the blade to stop rotating

Performing a mitre cut
• If the workpiece does not fit within the maximum workpiece dimensions specified within the ‘Specification’, adjust the support structures to accommodate the workpiece during the cutting procedure

1. Adjust the Protractor Gauge (43) to the desired angle. For instructions on Protractor Gauge adjustment and calibration, see ‘Adjusting the protractor gauge’
2. See ‘Performing a cross cut’ for cutting procedure instructions

Performing a rip cut

WARNING: Ensure the Rip Fence (53) is used when performing rip cuts, performing free-hand cuts is dangerous.
ALWAYS check the fence is securely locked into position before performing cuts.
WARNING: When performing rip cuts and whenever possible, keep hands clear of the Saw Blade (2) and use the Push-Stick (40) to feed the workpiece if there is less than 6″ between the fence and the blade.
WARNING: NEVER attempt to pull the workpiece back during the cutting process. Turn the machine off and wait for the Saw Blade to stop rotating before removing the part-cut specimen.

• If the workpiece does not fit within the maximum workpiece dimensions specified within the ‘Specification’, adjust the support structures to accommodate the workpiece during the cutting procedure

1. Adjust and lock the Rip Fence by closing the Rip Fence Clamps
2. Remove the Protractor Gauge (43)
3. Position the blade so the highest point is approx. 3.2mm higher than the top of the workpiece
4. Hold the workpiece flat on the table and against the Rip Fence. Keep the workpiece at least 25mm away from the Saw Blade.
5. Switch the Contractor Saw ‘on’ and allow the Saw Blade to reach the operating speed
6. Whilst holding the workpiece against the fence and flat to the table, slowly feed the workpiece through the Saw Blade. Maintain an even pushing force until the entire workpiece has passed through the saw blade. Use the Push-Stick (40) to continue feeding the workpiece through the blade when the trailing edge is less than 6″ away

Performing a bevel rip cut

WARNING: When performing a bevel rip cut, always ensure the Rip Fence (53) is on the right hand side of the Saw Blade (2). The Saw Blade shall never be angled towards Rip Fence.
Note: This operation follows the same procedure as ‘Performing a rip cut’ except the Saw Blade angle is set to a value other than ‘0°’.

• If the workpiece does not fit within the maximum workpiece dimensions specified within the ‘Specification’, adjust the support structures to accommodate the workpiece during the cutting procedure

1. Unlock the Locking Lever (21) and the angle of the Saw Blade (2) using the Bevel Angle Adjuster (16)
2. When the desired angle is set, lock the Saw Blade into place using the Locking Lever
3. Follow the cutting procedure as instructed in ‘Performing a rip cut’

Performing a bevel cross cut

Note: This operation follows the same procedure as ‘Performing a cross cut’ except the angle is set to a value other than ‘0°’

• If the workpiece does not fit within the maximum workpiece dimensions specified within the ‘Specification’, adjust the support structures to accommodate the workpiece during the cutting procedure

1. Unlock the Locking Lever (21) and adjust the Saw Blade’s (2) angle using the Bevel Angle Adjuster (16)
2. When the desired angle is set, lock the adjustment into place using the Locking Lever
3. Follow the cutting procedure as instructed in ‘Performing a cross cut’

Performing a slot cut
WARNING: DO NOT stack dado blades with this machine. The contractor table saw does not support using multiple
blades on the Arbor (34).

1. Detach the Blade Guard (3) and the Anti-Kickback Device (8) by twisting the Guard Securing Clip (6) and the Anti-Kickback Securing Clip (7)
2. Lower the Riving Knife (5) into its slot cutting position, Fig. I
   Note: See ‘Riving knife installation’ for instructions regarding the changing of Riving Knife positioning.

Accessories

• A range of accessories, including Rugged Transit Kit (TWX7RTK), Side Support (TWX7SS) and Outfeed Support (TWX7OS), is available from your Triton dealer. Spare parts can be purchased from your Triton dealer or online at www.toolsparesonline.com

Maintenance

WARNING: ALWAYS disconnect the Workcentre from the power supply, before cleaning, changing accessories, making adjustments, or carrying out maintenance.
WARNING: ALWAYS wear protective equipment including eye protection and suitable cut-proof gloves when cleaning or carrying out maintenance.
WARNING: ALWAYS wear suitable cut-proof gloves when handling the Saw Blade (2). Not doing so may result in cuts, or harm to the operator.
Saw blade replacement

WARNING: The rated speed of the saw blade must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.

1. Detach the Blade Guard (3) from the Riving Knife (5) by removing the screw securing the guard to the Riving Knife

2. Loosen the hex screw located at the infeed end of the Kerf Plate (27), and use the Kerf Plate Access Hole to release the plate, Fig. F

3. With the Locking Lever (21) unlocked, raise the Arbor (34) to its maximum height by turning the Blade Height Winder (15) anticlockwise

4. Lock the Blade Height Winder into position using the Locking Lever

5. Remove the old Saw Blade (2) by securing the Arbor Holder (32) with Multi-Tool 1 (41), whilst simultaneously removing the Blade Securing Nut (33) with Multi-Tool 2 (42)

6. Install the two halves of the Blade Flange (35) on to the new Saw Blade, then install the blade assembly on to the Arbor, Fig. O
   Note: Ensure the Saw Blade is installed in the correct orientation. The blade direction arrow found on the Saw Blade should match the direction of the arrow on the Blade Guard.

7. Fasten the new Saw Blade into place by securing the Arbor Holder with the Multi-Tool 1 whilst tightening the Blade Securing Nut with Multi-Tool 2

8. Reinstall the Kerf Plate and the Blade Guard

Kerf plate replacement
WARNING: When the Contractor Saw is subject to constant use, the kerf plate may deteriorate. The kerf plate must remain in good condition at all times. Replace if necessary.

1. Detach the Blade Guard (3) from the Riving Knife (5) by removing the screw securing the guard to the Riving Knife
2. Loosen the hex screw located at the infeed end of the Kerf Plate (27), and use the Kerf Plate Access Hole (24) to release the plate, Fig. F
3. Install the new Kerf Plate and/or Sacrificial Plate (28)
4. Level the Kerf Plate, see `Kerf plate levelling’ for detailed instructions
5. Reinstall the Blade Guard

Cleaning

• Keep your machine clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the machine’s service life. Clean the body of your machine with a soft brush or dry cloth. If available, use clean, dry, compressed air to blow through the ventilation holes
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before use

Clearing debris blockages

1. With the tool switched `off’ and disconnected from the power supply. Detach the Blade Guard (3) from the Riving Knife (5) by removing the screw securing the Blade Guard to the Riving Knife
2. Loosen the hex screw located at the infeed end of the Kerf Plate (27), and use the Kerf Plate Access Hole to release the plate, Fig. F
3. Remove the Dust Chute Panel (14) and any vacuum connections connected to the Dust Extraction Port (11)
4. Locate and clear the debris blockage
5. Reinstall the Blade Guard, Kerf Plate, Dust Chute Panel and any vacuum connections once the blockage has been cleared

Lubrication

• Lubricate all moving parts with PTFE spray at regular intervals, especially after heavy use or cleaning
  WARNING: DO NOT lubricate with oil or silicone-based maintenance sprays. Lubricant residue will combine with wood and dust leading to dirt build-up, which may interfere with moving parts and mechanisms. ONLY dry lubricate, using PTFE spray.

Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: tritontools.com/en-US/Support
Address: Powerbox Boundary Way Lufton Trading Estate Yeovil, Somerset BA22 8HZ, United Kingdom

Storage

• Store this tool and its accessories after use in its case, in a dry, secure place out of the reach of children

Disposal

Always adhere to national regulations when disposing of power tools that are no longer functional and are not viable for repair.

• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct way to dispose of power tools

Troubleshooting

Guarantee
To register your guarantee visit our web site at www.tritontools.com* and enter your details. Your details will be included on our mailing list (unless indicated otherwise) for information on future releases. Details provided will not be made available to any third party.

Purchase Record
Date of Purchase: / / Model: TWX7CS001 Serial Number:____ (located on tool housing) Retain your receipt as proof of purchase.

WARNING
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated rubber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles

References

• ToolSparesOnline | Tool spares for Triton, GMC, Silverline, Vanvault, Defender and Rhino
• Triton Tools | Precision woodworking power tools for over 35 years | TritonTools.com
• Triton Tools | Precision woodworking power tools for over 35 years | TritonTools.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>