DETECTO 8500 Portable Stretcher Scales Instruction Manual

8500 Portable
Stretcher Scale
Operating Instructions

CAUTION! This scale weighs approximately 115 pounds (52 kilograms).
If you think it is too heavy for you to lift or lower, ask someone to help you.
Damage to the load cells can occur if the scale is dropped or allowed to fall from the transport position. If damage to the scale is determined to have been caused by falling or dropping the scale, the warranty will be voided.

Lifting Scale from Floor to Transport Position

1. Note that the indicator can be attached to the scale platform when in Transport/Storage position.

2. Stand close to the scale with your feet 8 to 12 inches apart.
   IMPORTANT! For maximum protection against damage, store scale flat on the floor, preferably near a wall.

3. Keeping your back straight, bend your knees until you’re in a squatting position. Always keep your back straight, and bend at the knees, until in a squatting position!

4. Firmly grasp handles on the scale and lifts straight up.
   Don’t twist to either side. Keep the scale close to you, not at arm’s length.

5. Use your leg muscles as you lift. Keep your back upright and in its natural posture. Lift steadily and smoothly without jerking.

Lowering Scale from Transport Position to Floor

1. From the transport position, stand close to the scale with your feet 8 to 12 inches apart.
2. Firmly grasp handles on the scale.
3. While stepping back, lower scale to the floor, keeping your back straight and bending your knees until you’re in a squatting position. Always keep your back straight, and bend at the knees, until in a squatting position!
4. Once the scale is in position on the floor, remove the indicator from the scale platform, and place it in the desired location to use.

IMPORTANT! Lift straight up. Don’t twist to either side. Keep the scale close to you, not at arm’s length.

|
---|---

Scale Preparation

1. Install six (6) “C” size batteries, or if ordered with scale, plug the small connector end of the AC power adapter cord into the power jack located on the back of the MV1 indicator and then plug the AC power adapter into the proper electrical outlet. IMPORTANT! DO NOT connect an AC power adapter to the indicator if alkaline batteries are installed.
2. Install the indicator on the scale bracket and then connect the load cell cable.
3. Place the scale on any hard, level, flat surface or low-cut carpet.
4. The scale is now ready for operation.

NOTE: For more information on installing the batteries (or the AC power adapter), mounting the indicator on the scale bracket, connecting the load cell cable, and setup and operation, refer to the MedVue Model MV1 Medical Weight Analyzer Owner’s Manual, 8555-M512-O1.

Basic Operation

WARNING! Only the attendant may move the stretcher or wheelchair on and off the scale platform. The attendant must assist the patient onto and off the scale platform. NEVER leave a patient unattended while they are on the scale platform. Failure to maintain control of the patient at all times can result in serious injury to you and/or the patient.

Stretcher Scale Operation

1. To weigh the patient, press the ON/OFF key, and then press the ZERO key to zero weight display.
2. Position the patient on the scale by pushing the stretcher onto the scale. Lock the stretcher wheels while weighing the patient.
3. When weight reading is steady, read the patient’s weight.
4. Remove the patient/stretcher from the scale by pushing down the opposite ramp.

Wheelchair Operation

1. To weigh the patient, press the ON/OFF key, and then press the ZERO key to zero weight display.
2. Position the patient on the scale by pulling the wheelchair onto the scale. NEVER PUSH a patient in a wheelchair on or off the scale. Lock the wheelchair wheels while weighing the patient.
3. When weight reading is steady, read the patient’s weight.
4. Remove the patient/wheelchair from the scale by backing down the ramp.

Zero Weight Display

1. If the indicator is not showing zero weight on the display, press the ZERO key.
2. The weight display will return to zero. The ZERO and STABLE annunciators will turn on to show a stable, center-of-zero gross weight condition.

Zero Weight Display with Stretcher/Wheelchair on Scale (Push Button Tare)

1. Place the stretcher/wheelchair on the scale, and then press the TARE key.
2. The display will change to show ENTER TARE WT and the weight of the stretcher/wheelchair scale.
3. Press the PRINT/ENTER key.
4. The display will return to zero with the NET annunciator turned on, to show that net weight is being displayed. The stretcher/wheelchair’s weight has been entered as “tare weight”.
5. Proceed with the weighing operation.

Metric Conversion
Press the UNITS key to toggle between pounds and kilograms. The lb or kg annunciator will turn on to show the weighing unit selected.

Printed in the USA
0065-0831-1M Rev B 12/19

Documents / Resources

| DETECTO 8500 Portable Stretcher Scales [pdf] Instruction Manual
8500, 8550, Portable Stretcher Scales, Stretcher Scales, Portable Scales, 8500, Scales
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>