Software s BLE LED Tag Supporting Software Owner’s Manual
- June 10, 2024
- Software s
Table of Contents
Software s BLE LED Tag Supporting Software Owner’s Manual
The software supporting the Bluetooth object-finding tag has three mainfunctions:
Bind the tag; Click/sweep at close range; Long-distance object
finding.Function 1, label binding action, this step is specially formulated
inordertoestablish a corresponding relationship between physical objects
(orders) andlabels.Function 2, close-range object-finding, is intended to be
used when the searchareais small (within 10 meters of visual range). This
function provides QR codescanningorafter selecting a certain label in the full
list, it will actively connect to thespecifieditem label and send an audible
and visual reminder. This function is a singleremindersearch (the length of
the reminder time can be set, 3-20 seconds).
Function 3, long-distance object finding, is intended to be used when
thesearchareais large (above 100 square meters). On the APP side of the smart
tablet,enterthe”Long distance Finding” menu, select a certain tag, and make a
prompt accordingtotheRSSI value of the tag; until the RSSI is greater than
-70db (about 3-8 meters away),connectthe tag device and The sound and light
prompts are sent in a loop until theAPPclicksto end the search and the object
is found.
Software main interface
Bind tag
First of all, you need to correspond to the label corresponding to the bound
item. After thelabel isattached to a certain item, the mobile phone is close
to the label and click the “Select Label”menu.After waiting for 5 seconds,
select the label with the largest RSSI value in the list (the label
namedefaults to RemindTag), the selected tag will keep flashing to confirm the
selection, thenenter theitem name, and the customized item number (to
facilitate subsequent scanning and selection), andclick “Complete Binding”.
See an example of a bound label:
Click to find objects
After entering the long-distance search or short-distance search menu, you can
choose to findobjectsbyclicking or scanning.
Scan barcode QR code to find objects
After clicking the small scan code icon, scan the specified barcode or QR code
correspondingtotheitem(“item number” in the binding step)
Find objects in close range
After selecting an item, enter the following interface. The small circle icon
in the upper right cornerindicates the status of the item being searched (red
if successful, gray if not found). Click the”One-timeFind” menu successfully,
and the label on the item will be displayed. The
correspondingflashingindicator light (the duration of the prompt can be
changed from 3 to 20 seconds).
Find objects in far range
After selecting an item, enter the following interface, click the “Start
Finding” menu, and thecurrentsignal value will be continuously updated as
shown in the figure on the right. When facingthedirectionof the item, the
signal value is relatively large, and the opposite signal value is smaller.
Whenit isabout3-8 meters away from the item, the signal value will be greater
than -70dBm, and the small Bluetoothicon in the upper right corner will be
displayed in red. At this time, the label on the itemwill keepflashing the
indicator light (the prompt will end after 3 seconds)
Label development and testing
This function is a test function specially developed for customers to develop
by themselves, which is convenient for customers to develop auxiliary tests by
the mselves.
FCC Caution
15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for
compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between theequipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
*RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>