FLOTIDE S700R V Series Top Mount Sand Filter User Manual

FLOTIDE S700R V Series Top Mount Sand Filter

FUNCTION

The filter uses special filter sand to remove dirt particles from pool water. The filter sand is loaded into the filter tank and functions as a permanent dirt removing media. When the control valve is in the FILTER position, the pool water which contains suspended dirt particles, is pumped through your piping system and is automatically directed by the patented filter control valve to the top of the filter tank. As the pool water is pumped through the filter, dirt particles are trapped by the sand bed, and filtered out. The cleaned pool water is returned from the bottom of the filter tank, through the control valve and back to the pool through the piping system. This entire sequence is continuous and automatic. It provides for total recirculation of pool water through your filter and piping system.

After a period of time, the accumulated dirt in the filter causes a resistance to flow, and the flow diminishes. This means it is time to clean your filter. With the control valve in the BACKWASH position, the water flow is automatically reversed through the filter so that it is directed to the bottom of the tank, up through the sand, flushing the previously trapped dirt and debris out the waste line. Once the filter is back-washed of dirt, set control valve to RINSE position and run pump for about 1/2 to 1 minute, and then set the control valve in the FILTER position, to resume normal filtering.

NOTE: Turn pump off before changing valve position.

MAIN DIMENSION

DIMENSION TABLE

INSTALL/START-UP OF FILTER

1. Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure.
2. Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always depress handle before turning.)
3. Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial back-washing of the filter is recommended to remove any impurities or fine sand particles in the sand media.
4. Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2 to 1 minute. Turn pump off and set valve to FILTER position and restart pump. The filter is now operating in the normal filter mode, filtering dirt particles from the pool water.
5. Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten connections, bolts, nuts, as required.
6. Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the pump and general piping system.) As the filter removes dirt and impurities from the pool water, the accumulation in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is 1.5 bar, higher than the initial “clean” pressure you noted, it is time to backwash the filter (see BACKWASH under filter and control valve functions).

NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually heavy initial dirt load in the water.

REPLACEMENT PARTS OF FILTER

REPLACEMENT PARTS OF MULTIPORT VALVE

800 8

| Pin for Handle| 1
3| 0111 81027| Washer for Handle| 1
4| 01051 025| 2.0″ Side Mount Valve Squareness Lid (White)| 1
5| 89280301| M6*32 Screw with Nut| 10
6| 0 11110 48| Connect tor for Pressure Gauge /St op p er| 1
7| 89021703| ! Drain Plug with ORing| 1
8| 06 0111

029

| Oiil Pressure Gauge With O-Ring (40 Psi)| 1
9| 0201 11

007

| O-Ring for 2.0 “Un io n| 8
10| 01051 03 3| 2.0″Connect or(White)| 3
11| 01171 154| I 2.0”Un ion (A/ E)| 3
12| 0105103 2| 2.0″Union Nu t{W hit e)| 3
13| 0201 11 009| O-Ring for 2.0″ Valve Lid| 1
14| 0111 811 002| ! washer for spring| 1
15| 02011022| O-Ring for 2.0″ Valve Rotor| 2
16| 03011 4014| Spring| 1
17| 01021 00 2| 2.0″ Valve Rotor| 1
18| 0231 11 003| !Spider Gasket| 1
19| 01051 027| 2.0″ Side Mount Valve Bottom Body {While)| 1
20| 892801 04| Sight Glass Wit h O- Ri ng| 1
21| 02011011| O-Ring for Union Tale| 1
22| 0105103 5| 2.0” Union Tale (While)| 1

FUNCTIONS OF VALVE POSITIONS

FILTER

WASTE

CLOSED

BACKWASH

RINSE

RECIRCULATE

GENERAL

1. Pipe tap boss provided for optional influent pressure gauge.
2. SERVICING VALVE( Stop pump, close gate valve in suction & discharge before proceeding):
   a. Set handle in filter position. b. Remove cover screws. c. Lift cover and key assembly out.

TO ASSEMBLE:

1. Place valve key so that wedge opening is at TOP port (handle in Filter psn.). Flat edge of cover screw lug should align with flat edge of body screw lug.
2. Position cover Oaring.
3. Secure assembly to body with cover screws. Tighten cover screws evenly and alternately. Do not over-tighten.

WARNING

THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING SYSTEM (e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE SYSTEM AND BECOME PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO

BE BLOWN OFF WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE

TURN PUMP OFF BEFORE CHANGING VALVE POSITION.

TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM, CLEAN PUMP STRAINER AND SKIMMER BASKETS REGULARLY.

DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>