FLOTIDE SS Pool and Spa Pump User Manual
- June 9, 2024
- FLOTIDE
Table of Contents
FLOTIDE SS Pool and Spa Pump User Manual
INSTALLATION
Only qualified, licensed electrician or contractors should install pump and wiring.
IMPORTANT ELECTRICAL
Electrical Contractors Please.
Note: FLOTIDE pumps must be wired to the supply through an approved and
correctly rated contactor.
Pump Mount Must:
- Be solid, level, rigid and free from vibration.
- Allow use of short, direct suction pipe. (To reduce friction losses & do not install the pump at more than 3M geometrical height from water level)
- Flowrates should be used in suction and discharge piping.
- Have adequate floor drainage to prevent flooding.
- Be protected from excess moisture.
- All adequate access for pump and piping servicing
NOTICE:
Pump suction and discharge connections have molded in thread stops, DO NOT try to screw pipe in beyond these st
OPERATION
CAUATION
Hazardous suction. Can trap hair or body part, causing severe injury or death.
Do not block suction.
NEVER run pump dry! Running pump dry may damage seals, causing leakage
and flooding! Fill pump with water before starting motor.
Before removing lid: STOP PUMP before proceeding. CLOSE GATE VALVES in
suction and discharge pipes. RELEASE ALL PRESSURE from pump and piping system.
NEVER tighten or loosen screws while pump is operation.
Do not block pump suction! To do so with body may cause severe or fatal
injury. Children using pool must ALWAYS have close adult Supervision!
Priming Pump:
- Release all air from filter and piping system: see filter owner manual.
- In a flooded suction system (water source higher than pump), pump will prime itself when suction and discharge valves are opened.
- If pump is not in a flooded suction system, unscrew and remove trap cover; fill trap and pump with water.
- Clean and inspect Ring; re-install on trap cover.
- Replace trap cover on trap; turn clockwise to tighten cover.
NOTICE: Tighten trap cover by hand only. Pump should prime now. Priming time will depend on vertical length of suction lift and horizontal length of suction piping.
Routine Maintenance
The only routine maintenance needed is inspection/cleaning of trap basket. Debris or trash that collects in basket, will choke off water flow through the pump. Follow instructions below to clean trap:
- Stop pump, close gate valve in suction and discharge, and release all pressure from system before proceeding.
- Unscrew trap lid (turn counterclockwise).
- Remove strainer basket and clean. Be sure all holes in basket are clear,flush basket with water and replace in trap with large opening at pipe connection port (between ribs provided). If basket is replaced backwards cover will not fit on trap body.
- Clean and inspect lid Ring; reinstall on trap cover.
- Clean Ring groove on trap body and Replace lid. To help keep lid from sticking, tighten hand tight only.
- Prime pump (see priming instructions above
SERVICE & REPAIR PARTS
Refer all service to your local agent or dealer as his knowledge of your equipment makes him the vest qualified source of information. Order all repair parts through your dealer. Give the following information when ordering repair parts:
- Unit nameplate data or serial number on label.
- Description of part.
TROUBLE SHOOTING
MOTOR DOES NOT START
- Disconnect switch or circuit breaker in off position
- Fuses blown or thermal overload open
- Locked motor shaft
- Motor windings burned out
- Defective starting switch inside singl phase motor
- Disconnected or defective wiring
- Low voltage
PUMP DOES NOT REACH FULL SPEED
- Low voltage.
- Pump connected for wrong voltage.
MOTOR OVERHEATS (protector trips)
- Low voltage.
- Motor windings connected for wrong voltage on dual voltage model.
- Inadequate ventilation.
PUMP DELIVERS NO WATER
- Pump is not primed.
- Closed valve in suction or discharge line.
- Leakage or air into suction system.
- Impeller clogged.
LEAKAGE OF WATER AT SHAFT
- Shaft seal requires replacement.
LOW PUMP CAPACITY
- Valve in suction or discharge line partly closed
- Suction or discharge line partly plugged
- Suction or discharge line too small
- Plugged basket in skimmer or hair and lint strainer
- Dirty filter
- Impeller clogged
HIGH PUMP PRESSURE
- Discharge valve or inlet fittings closed too much
- Return lines too small
- Dirty filters
NOISY PUMP AND MOTOR
- Plugged basket in skimmer or hair in lint strainer
- Worn motor bearings
- Valve in suction line partly closed
- Suction line partly plugged
- Vacuum hose plugged or too small
- Pump not supported properly
AIR BUBBLES AT INLET FITTINGS
- Leakage of air into suction line at connections or valve stem
- Cover gasket of hair and lint strainer needs cleaning
- Low water level in pool
NOTE: If the recommendations in the trouble shooting portion of this manual do not solve your particular problem (s), please contact your local dealer for service.
PUMP PARTS FOR SS
Key No.| Part No.| Product Description| Qty| Key
No.| Part No.| Product Description| Qty
---|---|---|---|---|---|---|---
1| 01201031| Transparent Lid| 1|
17
| 89022110| Motor SS033( 220V/ 50HZ)| 1
2| 02011074| O- Ring for lid| 1| 89022105| Motor SS050( 220V/ 50HZ)| 1
3| 01112051| Basket| 1| 89022106| Motor SS075( 220V/ 50HZ)| 1
4| 01021064| SS Pump Pre- filter| 1| 89022107| Motor SS100( 220V/ 50HZ)| 1
5| 89280105| 1. 5″ union| 2| 89022108| Motor SS120( 220V/ 50HZ)| 1
6| 89022402| Drain Plug With O’ ring| 1| 89022201| Motor SS020( 220V/ 60HZ)|
1
7| 02011004| O- Ring for diffuser| 1| 89022202| Motor SS033( 220V/ 60HZ)| 1
8| 01111014| Diffuser| 1| 89022203| Motor SS050( 220V/ 60HZ)| 1
9
| 01311015| Impeller SS020( 220V/ 50HZ)| 1| 89022204| Motor SS075( 220V/
60HZ)| 1
01311016| Impeller SS033( 220V/ 50HZ)| 1| 89022205| Motor SS100( 220V/
60HZ)| 1
01311017| Impeller SS050( 220V/ 50HZ)| 1| 89022206| Motor SS120( 220V/
60HZ)| 1
01311018| Impeller SS075( 220V/ 50HZ)| 1| 89022305| Motor SS020( 110V/
60HZ)| 1
01311019| Impeller SS100( 220V/ 50HZ)| 1| 89022306| Motor SS033( 110V/
60HZ)| 1
01311014| Impeller SS120( 220V/ 50HZ)| 1| 89022301| Motor SS050( 110V/
60HZ)| 1
01311023| Impeller SS020( 220V/ 60HZ)| 1| 89022302| Motor SS075( 110V/
60HZ)| 1
01311024| Impeller SS033( 220V/ 60HZ)| 1| 89022303| Motor SS100( 110V/
60HZ)| 1
01311015| Impeller SS050( 220V/ 60HZ)| 1| 89022304| Motor SS120( 110V/
60HZ)| 1
01311016| Impeller SS075( 220V/ 60HZ)| 1|
18
| 04016028| Capacitor for SS050 Pump| 1
01311017| Impeller SS100( 220V/ 60HZ)| 1| 04016019| Capacitor for SS075
Pump| 1
01311018| Impeller SS120( 220V/ 60HZ)| 1| 04016021| Capacitor for SS100
Pump| 1
01311023| Impeller SS020( 110V/ 60HZ)| 1| 04016009| Capacitor for SS050
Pump| 1
01311024| Impeller SS033( 110V/ 60HZ)| 1| 04016010| Capacitor for SS075
Pump| 1
01311015| Impeller SS050( 110V/ 60HZ)| 1| 04016012| Capacitor for SS100
Pump| 1
01311016| Impeller SS075( 110V/ 60HZ)| 1| 04016032| Capacitor for SS020
Pump| 1
01311017| Impeller SS100( 110V/ 60HZ)| 1| 04016033| Capacitor for SS033
Pump| 1
01311018| Impeller SS120( 110V/ 60HZ)| 1| 04016030| Capacitor for SS020
Pump| 1
10| 89022403| M8 16 Screw with washer| 4| 04016031| Capacitor for SS033 Pump|
1
11| 04015033| 1/ 2″ Mechanical seal| 1| 19| 89022112| Cable Box for SS050-
SS120 Pump| 1
12| 02011090| O- Ring for Flange| 1| 20| 89022111| Cable Box for SS020- SS033
Pump| 1
13| 01021065| SS Pump Flange| 1| 21| 89021505| Cable Box for SS050- SS075
Pump| 1
14| 03011035| M6 30 Screw| 8| 22| 01031027| Cooling fan for SS050- SS120
Pump| 1
15| 02011156| Motor Slinger for SS020;SS033| 1| 01031026| Cooling fan
for SS020- SS033 Pump| 1
15| 02011153| Motor Slinger for SS050- SS120| 1| 23| 01031011| Fan Cover
for SS020- SS033 Pump| 1
16| 89022404| Motor support| 1| 01031010| Fan Cover for SS050- SS120 Pump| 1
17| 89022109| Motor SS020( 220V/ 50HZ)| 1| 24| 02011104| O- Ring| 2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>