HOLLYLAND HL-AROCAM USB High-Definition Live Camera User Manual

June 4, 2024
HOLLYLAND

HOLLYLAND HL-AROCAM USB High-Definition Live Camera

Note

  • During the installation and operation, all electrical safety regulations of the country and region of use must be strictly observed.
  • Please use the power adapter that comes standard with this product.
  • Do not connect multiple devices to the same power adapter (exceeding capacity of the adapter may generate excessive heat or cause fire).
  • Do not rotate the camera by hand, otherwise it may cause mechanical failure.
  • When installing this product on a wall or ceiling, make sure the device securely and there are no obstacles within the rotation range; Do not power on until all installations are completed.
  • To avoid heat build-up, please keep smooth ventilation around the device.
  • If the device smokes, smells, or makes noises, please turn off the power and unplug the power cord immediately, then contact the dealer in time.
  • This device is not waterproof, please keep the device dry.
  • This product has no user serviceable parts, damage caused by disassembly by the user is not covered by the warranty.

Specific frequencies of electromagnetic field may affect the image of the camera!

Packing List

Name Quantity
Camera 1
Power Adapter 1
USB Cable 1
Remote Control 1
User Manual 1

Quick Start

  1. Please check connections are correct before starting.
    USB High-Definition Live Camera

  2. Connect the power adapter to the power connector on the rear panel of the camera. The power indicator on the front panel of the camera turns on.

  3. After the camera is powered on, it starts to initialize, right up to the limit position, and then both horizontal and vertical go to the middle position. When the motor stops running, it means that the initialization is completed. (Note: If preset 0 is saved, PTZ will move to preset 0)

About Product

Features
  • Full Function USB Interface

Full function USB interface, compatible with USB 3.0 and USB 2.0, support video and encoding image output, support the UVC
V1.1 and UAC 1.0 protocol.

  • 080P Full HD

High-quality 1/2.8-inch HD CMOS sensor with 2.07 million effective pixels for high-quality images up to 1920×1080. The output frame rate is up to 60fps/s to present clear and realistic high-definition video and vividly showing the expressions and movements of the characters.

  • 72.5° Wide-angle Lens

Exclusively customized 72.5° high-quality ultra-wide-angle lens, support 12x optical zoom.

  • Low Illumination

The new CMOS image sensor with ultra-high SNR can effectively reduce the image noise under low illumination. The application of 2D and 3D noise reduction algorithm greatly reduces the image noise even under the condition of ultra- low illumination, it keeps the picture clean and clear, and the SNR of image is as high as 55dB.

  • Remote Control

Camera can be controlled remotely through the RS232 serial port.

  • Leading Auto Focus Technology

Using advanced focusing algorithm and TOF module assists focusing, the lens can focus quickly, accurately and stably.

  • Multiple Interfaces

Support audio and video output through HDMI, USB 3.0 and network interface.

  • Portrait

Support portrait output.

  • Two Power Supply Modes

Simultaneously support USB 5V and DC 12V power supply.

  • Easy to Use

No need to download the driver, USB output plug and play to take a convenient and simple user experience.

Specifications

Camera

Signal System| 1080P60, 1080P50, 1080P30,

1080P25, 720P60, 720P50

Sensor| 1/2.8 inch, CMOS,

Max Effective Pixel: 2.07M

Scanning Mode| Progressive
Lens| 12x, f = 3.5mm ~ 42.3mm, F1.8 ~ F2.8
Minimum Illumination| 0.5 Lux @ (F1.8, AGC ON)
Shutter| 1/30s ~ 1/10000s
White Balance| Auto, Indoor, Outdoor, One Push, Manual, VAR
Backlight

Compensation

| Support
Digital Noise Reduction| 2D&3D Digital Noise Reduction
Signal Noise Ratio| ≥55dB
Horizontal Angle

of View

| 72.5° ~ 6.9°
Vertical Angle of View| 44.8° ~ 3.9°
Horizontal Rotation Range| ±170°
Vertical Rotation

Range

| -30° ~ +90°
Pan Speed Range| 2.7° ~ 35.7°/s
Tilt Speed Range| 2.7° ~ 31.5°/s

USB High-Definition Live Camera

H & V Flip Support
Image Freeze Support
Number of Preset 255
Preset Accuracy 0.1°

USB Features


Operate System

| Windows 7, Windows 8, Windows 10, Mac OS X,

Linux, Android

Color System/ Compression| YUY2/MJPEG


Video Format

| l YUY2: 1080P@30fps (max.)

l MJPEG:        1080P@30fps (max.)

USB Audio| UAC1.0
USB Video Communication Protocol| ****

UVC 1.1

UVC PTZ| Support
Network Features
Video Compression| H.264/ MJPEG
Video Stream| First/Second Stream
First Stream Resolution| 1920×1080, 1280×720
Second Stream Resolution| 1280×720, 640×360
Bit Rate for First Stream| 32Kbps ~ 20480Kbps
Bit Rate for

Second Stream

| 32Kbps ~ 6144Kbps
Bit Rate Control| CBR, VBR
Frame Rate| 50Hz: 1fps ~ 50fps, 60Hz: 1fps ~ 60fps
Audio Compression| AAC
Audio Bit Rate| 96Kbps, 128Kbps, 256Kbps


Protocols

| TCP/IP, HTTP, RTSP, RTMP(S), ONVIF, DHCP,

Multicast, etc.

Input/Output Interface

Input/Output Interface

LINE IN

Interface

| 1 x LINE IN: 3.5mm

Line In Interface


Communication Interface

| 1 x RS232 IN: 8pin Min DIN, Max Distance: 30m, Protocol: VISCA/Pelco-D

/Pelco-P

Network Interface| 1 x NET: 10M/100M

Adaptive Ethernet Port

USB Interface| 1 x USB 3.0: Type C
HDMI Interface| 1 x HDMI: Version 1.4b
Power Jack| JEITA type (DC IN 12V)/ USB Type-C (DC IN 5V)
Physical Parameter
Input Voltage| DC 12V/USB 5V
Input Current| 12V 1.0A (max.)/

5V 1.5A (max.)

Operating Temperature| -10°C ~ 40°C
Storage

Temperature

| -40°C ~ 60°C
Power Consumption| 12W (max.)
Dimension (mm)| 142.2 x 151.9 x 175.8
Net Weight| 1.5Kg

Interfaces and Keys
Item Name
1 RS232 Interface
2 Network Interface
3 HDMI Interface
4 USB 3.0 Interface
5 LINE IN Interface
6 DC 12V Interface
Dimension
 Installation

Note

The installation diagram is for reference only. The brackets and screws are not standard. For packing accessories, please refer to the actual product.

Key Description
  • (Standby) Key
    Press to enter standby mode. Press again to resume to normal mode.
    Note: The power consumption in standby mode is approximately half of that in normal mode.

  • Number Key
    To set preset or call preset

  • Key
    Use with other keys.

  • PRESET Key
    Set preset: Store a preset position. [PRESET] + Number key (0-9): Set a corresponding preset position.

  • HOME Key
    Confirm selection or press to turn PTZ back to the middle position.

  • Return key
    Press to return to the previous menu .

  • ZOOM Key
    SLOW: Zoom In [+] or Zoom Out [-] FAST: Zoom In [+] or Zoom Out [-] Simultaneously press L/R SET + 1 [STD]: Set

  • L/R SET Key
    Press with 1 or 2 key to set the direction of the Pan-Tilt.
    Simultaneously press L/R SET + 1 [STD]: Set  the Pan-Tilt turn the same direction as the PTZ control key.
    Simultaneously press L/R SET + 2 [REV]: Set the Pan-Tilt turn the opposite direction as the PTZ control key.

  • Focus adjustmen t : Press [AUTO] to adjust the focus automatically.
    Press [MANUAL] to adjust the focus manually.
    When in manual focus mode, press [FAR] to focus on far object or [NEAR] to focus on near object.

  • Control slect key
    Camera selection:
    Press to select and control the camera.

  • Keys
    Use with other keys.

  • IR Remote Control Key
    [] + [#] + [F1]: Address 1
    [
    ] + [#] + [F2]: Address 2
    [] + [#] + [F3]: Address 3
    [
    ] + [#] + [F4]: Address 4Clear the preset position:

  • [RESET] + Number key (0-9).
    Press arrow button to perform panning and tilting. Press [HOME] button to face the camera back to front.
    Or: [*] + [#] + [CLEAR PRESET]: Erase all the preset individually.

  • PTZ Control Ke
    Press arrow button to perform panning and tilting. Press [HOME] button to face the camera back to front

  • MENU Key
    Enter or Exist OSD MENU

  • . BACKLIGHT Key
    Backlight ON/OFF: Press repeatedly to enable or disable the backlight compensation. NOTE:

    • Effective only in auto exposure
    • If there is a light behind the subject, the subject will become dark, press the backlight key to enable the backlight compensation.

Press again to disable this function.

  • . P/T RST (PTZ Reset) Key __Press to preset Pan/Tilt self-test.

Image Freezing Function

  • Manual freeze: Press the [F4] key to open the freezing function, “Freeze” will be displayed on the left upper corner. To cancel the freeze function, press [F4] key again, “Unfreeze” shows on the left upper corner and it will be disappeared automatically five seconds later.
  • Image freeze when recalling the preset: After enable the “Image Freeze” function by the OSD menu setting, the screen will remain the previous image when recalling the The screen will switch to the preset image after the camera turn to the preset position.
    Shortcut Key

[] + [#] + [1]: OSD menu default English
[
] + [#] + [3]: OSD menu default Chinese
[] + [#] + [4]: Display current IP address
[
] + [#] + [6]: Quickly recover the default
[] + [#] + [8]: Check the camera version
[
] + [#] + [9]: Quickly set up inversion
[*] + [#] + [MANUAL]: Restore to default IP

GUC SETTING

Press [MENU] key to display the main menu. Use the arrow key to move the cursor to desired item and press the [HOME] key to confirm to enter the corresponding sub-menu

MENU

Exposure
Color
Image
P/T/Z
Noise Reduction
Setup
Communication Setup
Restore Default
[Home] Enter
[Menu] Exit

EXPOSURE

When in main menu page, move the cursor to [Exposure] and press [HOME] key to confirm to enter the exposure page as below.

EXPOSURE

Mode Auto
Exp Comp Mode Off
Backlight Off
Gain Limit 1
Anti-Flicker 50Hz
Meter  Average

  • DRC  3
  • Select Item Change Value
  • [Menu] Back

Mode: Auto, Manual, SAE, AAE, Bright.
Exp Comp Mode : On, Off (Effective only in Auto mode).
ExpComp: -7 ~ +7 (Effective only in
ExpCompMode item to On).
Backlight: On, Off (Effective only in Auto
mode).
Bright: 0 ~ 17 (Effective only in Bright mode).

Gain Limit: 0 ~ 15 (Effective only in Auto, SAE, AAE, Bright mode).
Anti-Flicker : Off, 50Hz, 60Hz (Effective only in Auto, AAE, Bright mode).
Meter: Average, Center, Smart, Top (Effective only in Auto, SAE, AAE, Bright mode).
Iris: F1.8, F2.0, F2.4, F2.8, F3.4, F4.0, F4.8, F5.6, F6.8, F8.0, F9.6, F11.0, Close (Effective only in Manual, AAE mode).
Shutter: 1/30, 1/40, 1/50, 1/60, 1/70, 1/80, 1/90, 1/100, 1/110, 1/120, 1/130, 1/140, 1/150, 1/160, 1/170, 1/180, 1/190 (Effective only in Manual, SAE mode).
Gain: 0 ~ 7 (Effective only in Manual mode). DRC: 0 ~ 8.

COLOR

When in main menu page, move the cursor to
[Color] and press [HOME] key to confirm to enter the color page as below.

COLOR
WB Mode Auto
RG Tuning 0
BG Tuning +1
Saturation 100%
Hue 7
AWB Sens High

  • Select Item
  • Change Value
  • [Menu] Back
IMAGE

When in main menu page, move the cursor to
[Image] and press [HOME] key to confirm to enter the image page as below.

IMAGE
Luminance 7
Contrast 7
Sharpness 5
Flip-H Off
Flip-V Off
B&W-Mode Off
Gamma EXT
Style Default

  • Select Item
  • Change Value
  • [Menu] Back

Luminance: 0 ~ 14.
Contrast: 0 ~ 14.
Sharpness: Auto, 0 ~ 15.
Flip-H: On, Off.
Flip-V: On, Off.
B: On, Off.
Gamma: EXT, Default, 0.45, 0.5, 0.56, 0.63. Style: Default, Beauty, Jewelry.

P/T/Z

When in main menu page, move the cursor to
[P/T/Z] and press [HOME] key to confirm to enter the P/T/Z page as below.

P/T/Z
SpeedByZoom On
AF-Zone Front
AF-Sense High
Display Info On
Image Freeze Off
Call Preset Speed 22
Pre Zoom Speed 5

  • Select Item
  • Change Value
  • [Menu] Back

SpeedByZoom: On, Off.
AF-Zone: Front, Top, Center, Bottom.
AF-Sense: Low, Normal, High.

Display Info: On, Off.
Image Freeze: On, Off.
Call Preset Speed: 1 ~ 24.
Pre Zoom Speed: 0 ~ 7.

NOISE REDUCTION

When in main menu page, move the cursor to [Noise Reduction] and press [HOME] key to confirm to enter the noise reduction page as below.

NOISE REDUCTION
NR2D-Level Auto
NR3D-Level Auto

  • Select Item
  • Change Value
  • [Menu] Back

NR2D Level (2D Noise Reduction): Auto, Off,
1 ~ 5.
B(3D Noise Reduction): Auto, Off, 1 ~ 8.

 SETUP

When in main menu page, move the cursor to
[Setup] and press [HOME] key to confirm to enter the setup page as below.

SETUP
Language EN
Video Format 1080P30
USB Mode BULK
USB Audio ON
Aux Focus ON

  • Select Item
  • Change Value
  • [Menu] Back

Language: EN, Chinese.
Video Format: 1080P30.
USB Mode: BULK, ISOC.
USB Audio: On, Off.
Aux Focus: On, Off

COMMUNICATION SETUP

When in main menu page, move the cursor to [Communication Setup] and press [HOME] key to confirm to enter the communication setup page as below.

COMMUNICATION SETUP
Protocol VISCA
V_Address 1
V_AddrFix Off
Net Mode Serial
Baudrate 9600

  • Select Item
  • Change Value
  • [Menu] Back

Protocol: Auto, VISCA, PELCO-D, PELCO-P.
V_Address: 1 ~ 7 (Effective only in Auto, VISCA protocol).
V_AddrFix: On, Off (When set to On, useless in 88 30 01 FF Command. Effective only in Auto, VISCA protocol).
P_D_Address: 0 ~ 254 (Effective only in Auto, PELCO-D protocol).
P_P_Address: 0 ~ 31 (Effective only in Auto, PELCO-P protocol).
Net Mode: Serial, Paral (Effective only in Auto, VISCA protocol).
Baudrate: 2400, 4800, 9600, 38400.

RESTORE DEFAULT

When in main menu page, move the cursor to
[Restore Default] and press [HOME] key to confirm to enter the restore default page as shown in below figure.

RESTORE DEFAULT
Restore? No
Change Value
[Home] OK
[Menu] Back

WEB Settings

Visit Camera

Visit http://192.168.100.88 to pop up the login window, then input username (default: admin) and password (default: admin). After login, it will show as below:

Control Camera

All pages include two menu bars:
Real Time Monitoring: Video image displaying with function buttons.
Parameter Setup: Parameter configurating.

  • Video Viewing Window
    The video viewing window is same as video resolution, the bigger the resolution, the bigger the playing area. Double click the viewing window to show full screen, double click again, to return to initialized size.
    Status bar in viewing window shown as below:
  1. Video Pause: Click to pause the real-time video, click again to resume.

  2. Audio Control: Click to adjust the volume or mute.

  3. Full screen switch button.

  4. Pan and Tilt Control
    The direction arrows and home button allow you to manually drive the camera to desired position.

  5. Zoom
    Zoom In and Zoom Out buttons allow for wide or narrow view of the space.

  6. Focus
    Focus In and Focus Out button allow for fine manual focus adjustment if the camera has any auto focusing problems on difficult object.

  7. PTZ Speeds
    Pan speed rate can be set to 1 ~ 24, Tilt speed rate can be set to 1 ~ 20. Zoom and Focus speed rate can be set to 0 ~ 7.

  8. PTZ Presets
    When the PTZ turns to the position that you would like to return to later, you can set presets for quick recall.
    Type a number (0 ~ 254) into the preset box and click “Set” button to save.

When the PTZ turn to other position, input the preset number and click “Call” button to turn the PTZ back to the preset position.

PTZ/OSD Dropdown

Move the cursor to dropdown menu, select and click “OSD” to open the on-screen menu and do menu settings on the interface.
Language Selection

Click to select “Chinese” or “English” to change the language of the webpage.

Video Settings
  1. Video Format
    Support 50Hz (PAL) and 60Hz (NTSC) formats

  2. Encode Level
    Support baseline, mainprofile and highprofile.

  3. Encode Codec
    Support H264 and MJPEG.

  4. Resolution
    First stream support 1920×1080, 1280×720. Second stream support 1280×720; 640×360. The bigger the resolution, the clearer the image, and the larger the code stream, the more network bandwidth will be taken.

  5. Bit Rate.
    You can specify the bit rate, the larger the bit rate, the clearer the image. The configuration of the bit rate needs to be combined with the network bandwidth. When the network bandwidth is narrow and the bit rate is configured larger, the video stream cannot be transmitted normally, and the visual effect will be worse.

  6. Frame Rate
    You can specify the size of the frame rate, the greater the frame rate, the smoother the image; the smaller the frame, the more beating the image.

  7. I Key Frame Interval
    Set the interval between two I frames, the bigger the interval, the slower the response when opening the image for the first time.

  8. Bit Rate Control
    Two modes for bit rate control:
    CBR (Constant Bit Rate): Video coder will be coding according to the preset speed.
    VBR (Variable Bit Rate): Video coder will adjust the speed based on preset speed to gain the best image quality.

  9. Slice Split Enable
    Enable or disable the Slice Split function.

  10. Split Mode
    Split Mode Fixed bytes.

  11. Slice Size
    Size for slice.

  12. Luminance
    Image Bright: 0~14 (Default is 7).

  13. Contrast
    Image Contrast: 0~14 (Default is 7).

  14. Sharpness
    Image sharpness: Auto, 0 ~ 15 (Default is 5).

  15. Gamma
    Options: EXT, Default, 0.45, 0.5, 0.56, 0.63 (Default is EXT).

  16. Black & White
    Options: Colorful, Black & White (Default is Colorful).

  17. Flip-H
    Turn on/off the Flip-H function.

  18. Flip-V
    Turn on/off the Flip-V function.

Audio Settings
  1. Audio Switch
    Enable or disable audio switch.

  2. Audio Type
    Audio type AAC.

  3. Sample Rate
    Sample rate 32K.

  4. Bit Rate
    Bit rate 96K, 128K, 256K selectable.

  1. Input Type
    Input type LINE IN.
  1. ADTS Options
    Options: On, Off.
 System Settings
  1. Reboot
    Click “Reboot” to restart system.

  2. Username and Password
    Modify the password of username and guest (use letters and Numbers only).

Network Settings
  1. Lan Settings
    The default the IP address is 192.168.100.88, the MAC address cannot be modified.

  2. Port Settings

    • HTTP Port
      The IP address identifies a network device and multiple network programs can run on the device, each network program uses the network port for data transmission. The port setting on this page is to set up which port the WEB SERVER program uses to transmit. During port mapping, it needs to be consistent with the port number (default is 80).

    • B. RTSP Port
      Set up the RTSP port, default is 554.

    • TCP Port
      Set up the TCP port, default is 5678.

    • UDP Port
      Set up the UDP port, default is 1259.

    • Sony Visca
      Sony Visca 52381.

  3. RTMP(S) Settings
    Set the MRL of RTMP(S) and select “on”, “off”,
    “video” and “audio” functions to enable or disable video and audio in the two streams.

  4. SRT Settings
    Turn On/Off SRT and set up the SRT Port, Encryption and Password.

  5. RTSP Settings
    Turn On/Off the RTSP Auth.

  6. ONVIF Settings
    Turn On/Off the ONVIF and ONVIF Auth.

  7.   Multicast Settings
    Turn On/Off Multicast, set up the Multicast Address (default is 224.1.2.3) and Port (default is 6688; 6688 is the multicast port of the first stream and 6690 is the multicast port of the second stream).

  8. NTP Settings
    Turn On/Off NTP time sync, Main time show and Sub time show; select the Time Zone; set up the Server address, Time interval and the Time Show Position of the two streams.

Device Information

The above information is for reference only, please refer to the real product for the actual specification.

Download the Upgrade Program

If you need the camera upgrade program, please contact the manufacturer.
WEB interface and parameters are subject to change without notice.

Troubleshooting

Image

  1. Check that the camera power supply is connected, the voltage is normal, and the power indicator is always on.
  2. Turn off the power switch to check whether the camera is self-testing.
  3. Check the cable of video platform and TV whether in correct connection.

Image jitters after the camera is properly connected

  1. Check whether the camera installation is stable
  2. Check whether any vibrating machinery or object near the camera.
  • There is no video image in Browser

IE browser does not support H5, you need to use VLC plug-in to view videos. Please visit VLC website (http://www.videolan.org/vlc)
to download and install the 32-bit VLC media player, after installation, the video image will be displayed normally when visit the camera. Other mainstream browsers already support H5 and do not need to install the VLC plug-in.

  • Unable to access camera through Browser
  1.  Using PC to access the network to test that the network access can work properly to eliminate the network fault caused by cable and PC virus until the PC and camera can ping each other.
  2. Disconnect the network, connect camera with PC separately and reset the IP address of PC if necessary.
  3. Check that the IP address, subnet mask and gateway settings for camera is correct.
  4. Check that the MAC address is conflicts.
  5. Check that the web port is modified, the default setting is 80.
  • Forget the IP address or login password Forget the IP address or login password

The default IP address is: 192.168.100.88; the default username and password are both: admin. Control

  • Remote control does not work
  1. Check and replace with new batteries.
  2.  Check whether the camera is in normal working mode.
  3. Check whether the address key of remote control can match the camera.
  • Serial port cannot control
  1. Check whether the protocol, address and baud rate of camera are consistent.
  2. Check whether the control line is properly connected.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals