RAB ENTRA 12 Wall Mount LED Doorway Light Instructions
- June 10, 2024
- RAB
Table of Contents
INSTRUCTIONS
ENTRA® 12 INSTALLATION
Light Instructions
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and
all applicable local codes. Proper grounding is required for safety. THIS
PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining
fixture. No user serviceable parts inside.
CAUTION: For proper weatherproof function all gaskets must be seated
properly and all screws inserted and tightened firmly. Apply weatherproof
silicone sealant around the edge of the wall mounting box and/or junction box.
This is especially important with an uneven wall surface. Silicone all plugs
and unused conduit entries.
MOUNTING TO THE JUNCTION BOX
- Loosen Door Screws (2) and open the Door. Screws will remain in place with Silicone Washers (2).
- Loosen Reflector Screws (2) and slide the Reflector down from the Housing.
- Knock out appropriate Slots when mounting to Junction Box (not supplied) and secure to Junction Box.
- Feed supply wires through Junction Box. Check the Gasket is fully sealed.
- Make sure all gaskets are properly seated. Place the Reflector on Housing and tighten the Reflector Screws (2). Close and tighten the Door Screws (2). Silicone all Plugs and unused conduit entries.
MOUNTING TO WALL
- Loosen Door Screws (2) and open the Door. Screws will remain in place with Silicone Washers (2).
- Loosen Reflector Screws (2) and slide the Reflector down from the Housing.
- Knock out appropriate Slots when mounting to the wall surface.
- Secure Housing to a sturdy wall. Use appropriate mounting hardware such as lag bolts and anchors with washers suitable for the mounting surface. Check the Gasket is fully sealed.
- Make sure all gaskets are properly seated. Place the Reflector on Housing and tighten the Reflector Screws (2). Close and tighten the Door Screws (2). Silicone all Plugs and unused conduit entries.
- If outdoor surface is irregular, use caulk to seal any gaps around the Housing.
ON/OFF WIRING
Universal voltage driver permits operation at 120V to 277VAC, 50 or 60 Hz
except fixtures factory ordered with a (PC) 120V photocell or (/PC2) 277V
photocell.
- Connect the black fixture lead to the (+) LINE supply lead.
- Connect the white fixture lead to the (-) COMMON supply lead.
- Connect the GROUND wire from fixture to supply ground.
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.
- Clean lens and fixture with non-abrasive glass cleaning solution.
- Do not open the fixture to clean the LED. Do not touch the LED.
TROUBLESHOOTING
- Check that the line voltage at the fixture is correct. Refer to wiring directions.
- Is the fixture grounded properly?
RAB Lighting is committed to creating high-quality, affordable, well-designed
and energy-efficient LED lighting and controls that make it easy for
electricians to install
and end users to save energy. We’d love to hear your comments. Please call the
Marketing Department at 888-RAB-1000 or email:
marketing@rablighting.com
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
© 2021 RAB LIGHTING Inc.
ENTRA 12 – IN – 1121
73288-RAB
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail Answered promptly –
sales@rablighting.com
Free Lighting Layouts Answered online or by request
RAB WARRANTY : RAB’s warranty is subject to all terms and conditions
found at rablighting.com/warranty.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>