KERBL 345580 LED Moisture-Proof Lamp Instructions
- June 10, 2024
- KERBL
Table of Contents
KERBL 345580 LED Moisture-Proof Lamp
Product Information
- Product Name: LED Moisture-proof Lamp Farm LINE
- Item Numbers: 345580 / 345581
- Manufacturer: Albert KERBL GmbH
- Country of Origin: Germany
- Application: Stationary installation for lighting in moist environments
- Technical Specifications:
- Performance/Luminous Flux: Not specified
- Input Voltage: Not specified
- Colour Temperature: Not specified
- Colour Rendering (CRI): Not specified
- Light Angle: Not specified
- Beam Angle: Not specified
- Service Life: Not specified
- Switch Cycles: Not specified
- Dimensions: Not specified
- Safety Class: Not specified
- Protection Class: Not specified
- Cos (Power Factor): Not specified
- Compliance: CE-/UKCA-mark confirming compliance with the Directives of the European Union or relevant UK legislation.
- Manufacturer Contact Information:
- Albert Kerbl GmbH Felizenzell 9, 84428 Buchbach, Germany
- Tel. +49 8086 933 – 100, Fax +49 8086 933 – 500
- Website: www.kerbl.de
Product Usage Instructions
- Read the operating instructions carefully before installing and using the LED Moisture-proof Lamp Farm LINE.
- The lamp is designed for stationary installation on sufficiently load-bearing ceiling or wall structures outside of arm’s reach.
- The lamp should ensure the required level of lighting and is not intended for use in places with deposition of conductive dust.
- Open the housing clips and remove the cover to access the internal components of the lamp.
- Unscrew the cable feed lock nuts and remove the seal. Guide the mains supply line through the lock nuts and cable feed and connect to the light strip connecting terminal.
- Use a mains supply line with a suitable diameter to ensure sufficient sealing and strain relief.
- Replace the cover and close the housing clips.
- Mount the light to the ceiling or wall using the supplied mounting plates and fixing materials suitable for the base.
- Do not tamper with the lamp or use it for any purpose other than its intended use. Improper use may result in physical injury or material damage and void warranty and liability claims.
Remember to keep these operating instructions in a safe place for later use.
Operating instructions
LED Moisture-proof Lamp Farm LINE (item no. 345580 / 345581)
General
These operating instructions comprise instructions for use and safety
information. Please read the instructions carefully and note the regulations
and relevant information before putting the lamp into operation. Please keep
these operating instructions in a safe place for later use!
Correct use
The lamp is used for stationary installation on sufficiently load bearing
ceiling or wall structures. Installation is done outside of arm‘s reach. The
lamp should ensure the required level of lighting. Not intended for use in
places with deposition of conductive dust. Any other use shall be deemed
incorrect. Improper use and tampering with the lamp will void warranty and
liability claims.
Safety instructions
CAUTION!
Risk of physical injury and material damage if used incorrectly!
- Installation should be carried out by a qualified electrical technician.
- Ensure the light is disconnected from the mains voltage before commencing work.
- Install and store the light out of the reach of children.
- Do not open the light, especially in case of defect. If required, contact the manufacturer.
- Only use original spare parts.
- Do not look directly into the light beam.
- Do not use chemicals for cleaning.
- This light is not suitable for accent lighting.
- This light cannot be dimmed.
- Do not operate the lamp in environments where flammable gases, vapours or dust may be present.
- Before each use, check that the lamp is in good condition. Do not operate the lamp if a component is defective.
- National and international safety, health and occupational safety regulations must be observed and complied with.
- When installing the mains supply, the appropriate standards, guidelines and requirements must be met.
- The consistency of the protective conductor up to the main ground of the building must be measured using appropriate means and in line with the applicable installation regulations on every lamp.
- Use sufficiently viable screws for fastening to the ceiling structure.
- Ensure the cover is properly closed so as not to impair the degree of protection against water ingress.
Installation
- Open the housing clips and remove the cover.
- Unscrew the cable feed lock nuts and remove the seal. Guide the mains supply line through the lock nuts and cable feed and connect to the light strip connecting terminal.
Caution! Use a mains supply line with a suitable diameter to ensure sufficient sealing and strain relief. - Replace the cover and close the housing clips. Mount the light to the ceiling or wall using the supplied mounting plates and fixing materials suitable for the base.
CE-/UKCA-conformity declaration
Albert KERBL GmbH hereby declares that the product / device described in these instructions complies with the fundamental requirements and other relevant stipulations and regulations. The CE-/UKCA-mark confirms compliance with the Directives of the European Union or the relevant UK legislation.
Electronic scrap
Disposing of this device after its service life is the responsibility of the
operator. Please consult the valid national regulations. The device must not
be disposed of in household waste. In accordance with the stipulations of the
EU Directive on the Disposal of Electrical and Electronic Devices, the device
can be disposed of free of charge at the local waste collection or recycling
centre. Alternatively, it can be returned to retailers who offer a collection
service. The proper disposal helps to ensure environmental protection and
prevents any adverse effects on human health and the environment.
Albert Kerbl GmbH
Felizenzell 9
84428 Buchbach, Germany
Tel. +49 8086 933 – 100
Fax +49 8086 933 – 500
www.kerbl.de
Kerbl Austria Handels GmbH
Wirtschaftspark 1
9130 Poggersdorf
Tel. +43 4224 81555
Fax. +43 4224 81555-62
www.kerbl-austria.at
Kerbl France Sarl
3 rue Henri Rouby, B.P 46 Soultz
68501 Guebwiller Cedex, France
Tel. : +33 3 89 62 15 00
Fax : +33 3 89 83 04 46
www.kerbl-france.com
References
- Everything around animal breeding, husbandry and agricultural supplies - Albert Kerbl GmbH
- Page d'accueil - Kerbl France
- Everything around animal breeding, husbandry and agricultural supplies - Albert Kerbl GmbH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>