HABYS Herbal Stamp and Towel Warmer Instruction Manual

HABYS Herbal Stamp and Towel Warmer

APPLICATION

A professional heater for stamps and towels by HABYS is a perfect piece of equipment for a massage room or a beauty salon. With its help, you will not only warm stamps and towels, but also disinfect them from all microorganisms.
Effectively selected power of the device is responsible for quickly reaching the temperature of 75°C, which is then maintained by means of a built-in thermostat. The integrated UV radiation source placed inside the heater effectively destroys microorganisms. Thanks to this, you can be sure that the towels are completely sterile

CONSTRUCTION

OPERATION

1. Make sure the product is on a level surface before opening the door or turning on the appliance.
2. Insert the plug into the electrical outlet.
3. Only clean stamps and clean and neatly rolled towels may be placed inside the heater on the prepared metal shelf.
4. After properly packing, close the door and turn on the heater.
5. Press the UV switch to perform disinfection, the correct functioning will be indicated by the blue backlight of the switch.
6. The door is equipped with a safety device that turns off the UV lamp in case the door is opened during sterilization, the UV lamp will not start working again until the door is closed thoroughly.
7. Press the power switch when the red indicator is on, which means the cabinet is in auto continuous heating mode at 75°C temperature setting.
8. The time required to reach the desired temperature of the towel may vary (due to the different starting temperature of the towel).
9. When the heater is not in use, remove the plug from the socket.
10. Store in a dry ventilated place.

EXPLOITATION REMARKS

1. The electrical socket used should meet the safety requirements for electricity and be in accordance with the operational requirements given on the rating plate.
2. Unauthorized persons are prohibited from disassembling the heater and elements for sterilization with ultraviolet rays.
3. The sequence of activation of the heater function: turn on the UV sterilizer first, then the heater. Do not open the cabinet door during disinfection or heating as this may adversely affect the disinfection and heating performance. Use the pliers to pick up items from inside the heated warmer. As far as possible, do not pick up products from inside using your hands, as this may cause secondary contamination and burns.
4. Regularly check the water collector to remove accumulated water. Remember to remove the plug from the socket before cleaning.
5. If the power cord is damaged, stop using the device and report the failure to a qualified service.
6. Any problems with the product should be dealt with by a professional electrician or serviceman.
7. It is forbidden to use the heater outdoors, in high temperature or with poor ventilation.
8. It is forbidden to use in rain or damp place.

TECHNICAL DATA

• Power supply: 220-240V
• Frequency: 50/60Hz
• Rated power: 8l – 130W (20l – 200W)
• Maximum temperature: 75 degrees Celsius
• UV source power: 3W
• UV radiation wavelength: λ=253.7nm
• UV intensity at 1m: 0.2W/m2
• Durability of the UV source: 8 000h
• Sterilization level of microorganisms: 99%
• Heater dimensions: 8l – 320mm x 270mm x 270mm (20l – 450mm x 333mm x 335mm)
• Heater capacity: 8l (20l)
• Heater weight: 8l – 4.5kg (20l – 8kg)
• Heater material: ABS plastic

WARRANTY CONDITIONS

1. For the purposes of the guarantee:
   • a) “Manufacturer” refers to HABYS Spółka z ograniczoną odpowiedzialnością (Limited Liability Company) with its registered seat in Jasło, ul. Produkcyjna 16, 38-200 Jasło, entered into the Register of Entrepreneurs kept by the District Court in Rzeszów, XII Commercial Division of the National Court Register, with the assigned KRS number: 0000513317, with the share capital in the amount of PLN 10.750.000 (ten million seven hundred fifty thousand zlotys), the capital has been fully paid up, NIP: 6852208438, REGON: 180186290.
   • b) “Buyer” refers to the final Buyer of the equipment, manufactured by the Manufacturer, including both the consumer and the entrepreneur.
   • c) “Distributor” refers to an entity that, under an agreement with the Manufacturer, sells the Equipment in a designated area.
   • d) “Authorized Service Centre” refers only to a service held by the Manufacturer or a service indicated by the Manufacturer and held by its Distributor,
   • e) “Equipment” refers to a movable item, manufactured by the Manufacturer, being the subject of the sales and to which the said warranty applies.
2. The manufacturer ensures good quality and efficient operation of the equipment for which the warranty card has been issued, for the period of: 2 years.
3. The guarantee repair does not include the activities provided for in the manual, which the Buyer is obliged to perform on his own (installation of the Equipment, maintenance of the Equipment, etc.).
4. Liability under the guarantee covers only defects resulting from causes inherent in the Equipment., In particular, the guarantee does not cover any damage resulting from improper or inconsistent use, storage, maintenance or transport of the Equipment, as well as colour differences between the parts exposed and not exposed to solar radiation, the influence of chemical or abrasive agents, atmospheric pollution or accidental punctures and abrasions, the presence of stains or rings from greasy or dying substances (fats, creams, lotions or oils), permanent staining with dyes such as inks, permanent markers or other non-permanent dyes used in the production of clothing (e.g. dyes used to make blue jeans).
5. The guarantee does not cover any mechanical damage to the Equipment.
6. The buyer loses the guarantee rights in the event of:
   • a) the Manufacturer states that the Equipment was repaired by entity other than the Authorized Service,
   • b) making any design modifications to the Equipment without the prior written consent of the Manufacturer,
   • c) using the Equipment contrary to its intended use,
   • d) using the Equipment after revealing any defect in it.
7. Regardless of the loss of the guarantee rights, described above, in point 6, the Manufacturer shall not be liable for any damage to property or caused to third parties, which may be caused by the use of the Equipment covered by the guarantee.
8. The guarantee does not exclude or limit the rights resulting from the warranty for defects. Exercising the rights under the guarantee does not affect the seller’s liability under the warranty for defects. If the Buyer exercises the rights under the guarantee, the time limit for the exercise of the rights under the warranty for defects is suspended on the date the Manufacturer is notified of the defect. The period runs further from the date of the Manufacturer’s refusal to perform the obligations arising from the guarantee or the ineffective expiry of the time for their performance.
9. The scope of the guarantee coverage is limited to the territory of the country in which the Equipment was sold.
10. The Manufacturer shall perform its obligations under the guarantee (removal of defects or damage to the structure of the Equipment arising from reasons inherent in the Equipment, and disclosed during the guarantee period) free of charge within 14 days from the date of delivery of the Equipment to the Manufacturer or the Authorized Service Centre. If the repair of the Equipment cannot be performed within the above-mentioned period, the Manufacturer shall inform the Buyer of the above, and also indicate the reasons for the delay and the expected date of fulfilment of the recognized guarantee request.
11. The use of the guarantee rights requires the total (cumulative) fulfilment of four conditions:
    • a) presenting a VAT invoice, receipt or other proof of purchase of the equipment to the Manufacturer, photographic documentation of the defective Equipment, together with a brief description of the reasons for submitting a guarantee claim,
    • b) reporting the defect within 14 (fourteen) days of its detection,
    • c) delivering the Equipment in original packaging at the expense of the Manufacturer, to the address indicated above in the guarantee card or to the address of the Authorized Service Centre,
    • d) designation of the place where the Manufacturer delivers the equipment after repairing it (limited to the country in which the Equipment was purchased).
12. The guarantee period is extended for the duration of the repair, starting from the date of delivery of the Equipment to the Manufacturer or to the Authorized Service Centre, to the date on which the Equipment was returned to the Buyer.
13. The responsibility of the Manufacturer or the Authorized Service Centre is to define the scope and the method of repairing the Equipment.
14. The guarantee is limited to the repair of the Equipment. The Manufacturer reserves the right to replace the Equipment with a non-defective one, if the repair exceeds the price of the Equipment indicated in the proof of purchase. Under the guarantee, the Buyer shall not be entitled to demand that the Equipment be replaced with a new one. The guarantee, in particular, does not cover liability for losses or damages incurred by the Buyer in connection with the fact that one is not able to use the Equipment.
15. The Manufacturer shall not be liable for any damage to the Equipment caused during the performance of the transport service by the delivery company until it is collected by the Manufacturer from the delivery company.
16. If the shipment of the Equipment was ordered by the Manufacturer, the Buyer is obliged to check the technical condition of the Equipment upon its receipt. If the Buyer finds that the Equipment has been damaged during the transport, the Buyer is obliged to:
    • a) immediately, not later than within 3 days from the date of receipt of the shipment, notify the Manufacturer of any damage to the Equipment that occurred during transport, in order to enable the Manufacturer to submit a complaint to the delivery company and pursue related claims,
    • b) provide the Producer with a complaint report drawn up between the Buyer and the delivery company.
17. The guarantee regulations contained in this document are the sole and exclusive guarantee rules for HABYS limited liability products.

Inne wersje językowe dostępne pod adresem: Other language versions available here:

www.habys.com/warrantymanuals

Manufacturer
Foshan Tonghai Sanitary Fittings Co., Ltd. No. 86, Xinma Road, Lecong Town, Foshan, Guangdong, China
Made in China

Authorized Representative
HABYS Sp. z o.o.
address: ul. Produkcyjna 16, 38-200 Jasło tel.: +48 887 766 115, info@habys.pl
www.habys.pl

References

• Stoły do masażu, stoły rehabilitacyjne, łóżka do masażu i rehabilitacji - Habys

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>