ZAMEL SBW-02 Wi-Fi 2-Channel Gate Controller User Manual
- June 10, 2024
- ZAMEL
Table of Contents
SBW-02 Wi-Fi 2-Channel Gate Controller
User Manual
BEFORE STARTING
PRODUCT DESCRIPTION:
The gate controller enables integration with any gate drive and walk gate and
enables remote control of a gate by means of the Supla mobile app. The device
can be mounted directly in the drive. Owing to universal 12÷24 V AC/DC power
supply it can be used in many applications. When the signals from the limit
switches are connected to the input of the controller we receive information
about opening and closing of the gate/walk gate.
FEATURES:
- Wireless control of the gate drive and walk gate using Wi-Fi technology,
- Universal inputs controlled by the supply potential,
- Two independent NO relay outputs,
- The state of the gate can be monitored by means of checking the state of limit switches,
- The controller can be controlled by the Supla mobile app from any place in the world,
- 12÷24 V AC / DC power supply for the controller.
WARNING!
The device must be connected to power supply in accordance with applicable
electrical and safety standards or regulations. See this User Manual for the
wiring instructions. Installation, wiring and setting of this product shall
only be done by qualified electrical engineers who have read and understood
this User Manual and the product features. Do not open or otherwise
disassemble the product enclosure; otherwise the product warranty will be void
and an electrocution hazard may occur. Prior to installing and wiring this
product, make sure that the wiring to be connected is not live. The conditions
and methods of transport, storage and operation of this product may affect its
performance. Do not install the product if any of its components is missing,
the product is damaged or deformed in any way. If any malfunctions are found,
consult the manufacturer.
ZAMEL Sp. z o.o. hereby declares that the radio-frequency (RF) device type
SBW-02 conforms to Directive 2014/53/EU. See the website below for the full EU
Declaration of Conformity: www.zamel.com
NOTICE
When installing this product, verify that this device is not directly exposed
to water or operation at high relative humidity. The temperature at the
installation site must be between -20°C and +55°C.
The SBW-02 RF receiver is intended for indoor installation.
If installed outdoors, place this device in an external water-tight enclosure
and secure against ingress of water, especially at the wiring terminals.
TECHNICAL SPECIFICATIONS
SBW-02
Rated supply voltage:| 12 ÷ 24 V AC / DC
Rated frequency:| 50 Hz
Rated power consumption:| 0,6 W
Transmission:| Wi-Fi 2.4 GHz b/g/n
Transmission range:| Wi-Fi range
Number of inputs:| 2
Number of output channels:| 2
Relay contact ratings:| 2 x NO 3 A / 250 V AC (normally open voltage-free
contact)
Number of terminals:| 8 (conductor cross-section up to 2,5 mm²)
Enclosure installation:| gate drive or installation box Ø 60 mm
Operating temperature range:| – 20 ÷ + 55°C
Enclosure protection rating:| IP20
Dimensions:| 47,5 x 47,5 x 20 mm
Weight:| 0,04 kg
Maximum output current-carrying capacity:| 3 A/250 V AC
GETTING STARTED IN 5 STEPS
LET’S BEGIN
Download, install and launch the supla mobile app
STEP 1
Install the app
5.1. INSTALL THE SUPLA MOBILE APP
STEP 2
create an account/log in
5.2. CREATING A SUPLA ACCOUNT
IF YOU DO NOT HAVE AN ACCOUNT
Create it by tapping “Create Account” in your app.
IF YOU ALREADY HAVE AN ACCOUNT
Enter the e-mail address which you have used to create the account.
CREATE AN ACCOUNT
On this page, enter the following data:
- e-mail address,
- password,
- password confirmation.
Confirm all information by tapping “Create an account”.
STEP 3
connect the power input wiring
5.3. WIRING CONNECTION DIAGRAM
Wire the SBW-02 to the power supply system as shown in the diagram.
STEP 4
Add the device
5.4. ADDING THE DEVICE AUTOMATICALLY
LAUNCH THE APP
Launch the app and tap “Add a device” in the menu.
LAUNCHING THE WIZARD
The “Add a device” wizard will be displayed. Tap „Next” to continue.
NETWORK PASSWORD
Choose a WiFi network to enable Internet connectivity for the device. Enter
the network password and tap “Next” to continue.
CONNECTING THE DEVICE
Wire the power supply to the device as shown in the diagram. Make sure that
the device STATUS LED responds as shown in the animation on screen.
If it does not, switch the device into the configuration mode by holding the
CONFIG button on the device. Next, press the START button.
NEW DEVICE REGISTRATION DISABLED
If the “New Device Registration Disabled” message is displayed, open this
website: https://cloud.supla.org/,
Log into your account, go to the “My SUPLA” tab and Enable Device Registration. Next, repeat the device adding process.
DEVICE ADDED SUCCESSFULLY
Adding a device is simple and should end without any problems. If the device
is added successfully, the following message is displayed: “Device
configuration successful”. Tap OK. Now, the supla app should display the
device which you have just added on the list. The SBW-02 STATUS LED in the
front goes on steadily when the connection with the server is active.
CAUTION!
If the connected device is not shown on the list immediately once the
configuration is complete, check the device STATUS LED. When added for the
first time, the STATUS LED of some devices may flash very fast and
irregularly. This happens when the device controller is updating its firmware.
A moment after the update, the STATUS LED should go on steadily which means
there is an active connection with the server.
ADDING THE DEVICE MANUALLY
Add the device manually when the automatic device adding mode of the supla app
fails somehow.
DEVICE CONFIGURATION MODE
To do this, switch the device into the configuration mode by pressing and
holding the CONFIG button until the STATUS LED starts to flash.
CONFIGURING THE DEVICE
Now, find the device in the available Wi-Fi network list on your mobile device
and connect to it. The Wi-Fi network name should begin with “ZAMEL-SBW-02”,
followed by the device serial number.
Open a web browser and type the following address in the address bar:
192.168.4.1 and open it.
The configuration page will be displayed. Here, you can easily change the
network settings.
When done, tap “SAVE” at the bottom of the screen. The message “Data saved!” should be displayed. To confirm the entered data, briefly press the CONFIG button on the device. If the device connects to the server successfully, the STATUS LED will go on steadily.
STEP 5
Control the gate
5.5. APPLICATIONS FUNCTIONS
SET UP OF SWITCH-ON TIME OF RELAY
After adding the device to control, the gate should be configuration. In this
case the switch-on time of the relay should be set.
Please go to https://cloud.supla.org/, log in to Your supla account, and go
to „My SUPLA”.
Then choose the device from the list.
A site with details of device will occur. Please choose „Type of relay” – here
You should choose the switch-on time: 0,5 sec, 1 sec, 2 sec…
Then push the button „save changes”.
RESETTING THE DEVICE
RESETTING THE DEVICE TO DEFAULT SETTINGS
-
Press and hold CONFIG
The STATUS LED should flash fast. -
Release the CONFIG button
The STATUS LED should flash fast. -
Press and hold CONFIG again
The STATUS LED should blink once. -
Release the button
The device has been reset to defaults and restarts now. The STATUS LED should flash fast.
MORE INFORMATION
Additional information and video material You can find by scanning QR code or by using the following link:
https://supla.zamel.com/en/product/sbw-02/
WARRANTY
-
ZAMEL Sp. z o.o. grants a 24-month warranty for the products it sells.
-
The warranty granted by ZAMEL Sp. z o.o. does not cover:
(a) defects caused by transport, handling or other factors;
(b) defects caused by improper installation or operation of the products manufactured ZAMEL Sp. z o.o.;
(c) defects caused by any modifications or alterations made by the BUYER or any third party to the sold products or to the equipment required for the proper operation of the sold products;
(d) defects caused by any force majeure event or another fortuitous event beyond any reasonable control of ZAMEL Sp. z o.o. -
The BUYER shall report all warranty claims in writing at the point of sale or to ZAMEL Sp. z o.o.
-
ZAMEL Sp. z o.o. will examine each warranty claim as regulated by the applicable provisions of the Polish law.
-
If found valid by examination, the warranty claim will be processed by replacement of the defective product, its repair or a refund of the price of purchase at the sole discretion of ZAMEL Sp. z o.o.
-
No rights of the BUYER arising from the statutory or regulatory laws concerning implied warranty for defects of sold goods are limited, prejudiced or excluded by this warranty.
CHECK ALSO OUR OTHER PRODUCT
Wi-fi roller blinds controller
Supla SRW-01
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>