ZAMEL mROW-02 Flush Mounted 2-Channel Wi-Fi Receiver Instruction Manual

: June 9, 2024
: ZAMEL

ZAMEL mROW-02 Flush Mounted 2-Channel Wi-Fi Receiver

ZAMEL mROW-02 Flush Mounted 2-Channel Wi-Fi Receiver
product

BEFORE GETTING STARTED

RECEIVER FEATURES:

Two-channel energy measurement,
Wi-Fi 2,4 GHz radio communication,
Works with ordinary switches and push-buttons,
Independent 2-channel control option,
Control possible locally with a switch or remotely via a smartphone
Ideal for installation under a 2-key switch which allows to add the smartphone control functionality,
the device has overcurrent protection.

WHAT’S INSIDE THE BOX

mROW-02 device
user’s manual

WHAT YOU NEED TO GET STARTED:

screwdriver / pliers,
max. 2.5 mm2 cable for connecting the power supply,
qualification certificate for voltages up to 1 kV is recommended.

WARNING

The device must be connected to power supply in accordance with applicable electrical and safety standards or regulations. See this User Manual for the wiring instructions. Installation, wiring and setting of this CAUTION product shall only be done by qualified
electrical engineers who have read and understood this User Manual and the product features. Do not open or otherwise disassemble the product enclosure; otherwise the product warranty will be void and an electrocution hazard may occur. Prior to installing and wiring this product, make sure that the wiring to be connected is not live. The conditions and methods of transport, storage and operation of this product may affect its performance. Do not install the product if any of its components is missing, the product is damaged or deformed in any way. If any malfunctions are found, consult the manufacturer.

INFORMATION

During installation, make sure that the receiver is not exposed to direct contact with water and that it does not operate in a humid environment. The installation place temperature should be within the range of -10 and +55°C.
The mROW-02 receiver is designed for indoor installation. When installed outdoors, the device should be placed in an additional enclosure of hermetic type and protected against water penetration – in particular where connection terminals are located.
ZAMEL Sp. z o.o. hereby declares that the type of mROW-02 radio device complies with Directive 2014/53/EU. The entire EU declaration of conformity is available at: www.zamel.com
Do not dispose of this device with other waste! In order to avoid harmful effects on the environment and human health, the used device should be stored in designated areas. For this purpose, you can dispose of household waste free of charge and in any quantity to a collection point set up, as well as to the shop when you buy new equipment.

TECHNICAL DATA

mROW-02

Rated supply voltage:| 230 V~, 50/60 Hz
Rated power consumption:| 1.2 W
Transmission:| Wi-Fi 2.4 GHz 802.11 b/g/n
Maximum transmit power:| ERP < 20 mW
Number of inputs:| 2
Compatible connectors:| monostable (bell buttons), bistable (standard light switches without backlight function)
Number of output channels:| 2
Relay contact parameters (normally open voltage-free contact):| 2 x NO 5 A / 250 VAC
Number of terminals:| 7 (conductor cross-section up to 1.5 mm2)
Enclosure installation:| gate drive or installation box Ø 60 mm
Operating temperature range:| -10 ÷ +55°C
Enclosure protection rating:| IP20
Dimensions:| 40 x 37.5 x 17 mm
Weight:| 0.031 kg
Maximum output current-carrying capacity:| 2 x 5 A / 250 V AC: incandescent and halogen light bulbs
– 750 W; LED lamps
– 60 W;
compact fluorescent lamps (CFL) – 250 W

GETTING STARTED IN 5 STEPS

LET’S GET STARTED
download, install and launch the supla mobile app

INSTALL THE SUPLA MOBILE APP

CREATING A SUPLA ACCOUNT

IF YOU DO NOT HAVE AN ACCOUNT
Create it by tapping “Create Account” in your app.

IF YOU ALREADY HAVE AN ACCOUNT
Enter the e-mail address which you have used to create the account.
CREATE AN ACCOUNT
On this page, enter the following data:
- e-mail address,
- password,
- password confirmation.
  Confirm all information by tapping “Create an account”.

WIRING DIAGRAM

Connect the mROW-02 device to the installation according to the following diagram. ZAMEL mROW-02 Flush Mounted 2-Channel Wi-Fi Receiver
5

ADDING THE DEVICE AUTOMATICALLY

OPEN THE APP
Then select “Add device” from the menu.
STARTING THE WIZARD
The Add Device Wizard will appear. To continue, press the “Next” button.
NETWORK PASSWORD
Choose a Wi-Fi network to enable Internet connectivity for the device. Enter the network password and tap “Next” to continue.
CONNECTING THE DEVICE
Wire the power supply to the device as shown in the diagram. Make sure that the device STATUS LED responds as shown in the animation on screen. If it does not, switch the device into the configuration mode by holding the CONFIG button on the device. Next, press the START button.
NEW DEVICE REGISTRATION DISABLED
If the “New Device Registration Disabled” message is displayed, open this website: https://cloud.supla.org/,
Log into your account, go to the “My SUPLA” tab and Enable Device Registration. Next, repeat the device adding process.
DEVICE ADDED SUCCESSFULLY
Adding a device is simple and should end without any problems. If the device is added successfully, the following message is displayed: “Device configuration successful”. Tap OK. Now, the supla app should display the device which you have just added on the list. The mROW-02 STATUS LED in the front goes on steadily when the connection with the server is active. CAUTION!
**** If the connected device is not shown on the list immediately once the configuration is complete, check the device STATUS LED. When added for the first time, the STATUS LED of some devices may flash very fast and irregularly. This happens when the device controller is updating its firm- ware. A moment after the update, the STATUS LED should go on steadily which means there is an active connection with the server.

ADDING THE DEVICE MANUALLY
Add the device manually when the automatic device adding mode of the supla app fails somehow.

DEVICE CONFIGURATION MODE
To do this, switch the device into the configuration mode by pressing and holding the CONFIG button until the STATUS LED starts to flash.
CONFIGURING THE DEVICE
Now, find the device in the available Wi-Fi network list on your mobile device and connect to it. The Wi-Fi network name should begin with “ZAMEL-mROW-02”, followed by the device serial number.
Open a web browser and type the following address in the address bar: 192.168.4.1 and open it.
The configuration page will be displayed. Here, you can easily change the network settings.
When done, tap “SAVE” at the bottom of the screen. The message “Data saved!” should be displayed. To confirm the entered data, briefly press the CONFIG button on the device. If the device connects to the server successfully, the STATUS LED will go on steadily.

APP FUNCTIONS

ZAMEL mROW-02 Flush Mounted 2-Channel Wi-Fi Receiver
16

ENERGY MEASUREMENT

ZAMEL mROW-02 Flush Mounted 2-Channel Wi-Fi Receiver
18

OVERLOAD PROTECTION

Put the device into configuration mode 11.
Connect to the Wi-Fi network 12.
Enter 192.168.4.1 in your browser 13.

RESETTING THE DEVICE

RESETTING THE DEVICE TO DEFAULT SETTINGS

Press and hold CONFIG
The STATUS LED should flash fast.
Release the CONFIG button
The STATUS LED will continue to flash.
Press and hold CONFIG again
The STATUS LED should blink once.
Release the CONFIG button
The device has been reset to defaults and restarts now.
The STATUS LED should flash fast.

MORE INFORMATION

Additional information and video material You can find by scanning QR code or by using the following link: https://supla.zamel.com/en/product/mrow-02/

WARRANTY

ZAMEL Sp. z o.o. grants a 24-month warranty for the products it sells.
The warranty granted by ZAMEL Sp. z o.o. does not cover:
- defects caused by transport, handling or other factors;
- defects caused by improper installation or operation of the products manufactured ZAMEL Sp. z o.o.;
- defects caused by any modifications or alterations made by the BUYER or any third party to the sold products or to the equipment required for the proper operation of the sold products;
- defects caused by any force majeure event or another fortuitous event beyond any reasonable control of ZAMEL Sp. z o.o.
The BUYER shall report all warranty claims in writing at the point of sale or to ZAMEL Sp. z o.o.
ZAMEL Sp. z o.o. will examine each warranty claim as regulated by the applicable provisions of the Polish law. If found valid by examination, the warranty claim will be processed by replacement of the defective product, its repair or a refund of the price of purchase at the sole discretion of ZAMEL Sp. z o.o.
No rights of the BUYER arising from the statutory or regulatory laws concerning implied warranty for defects of sold goods are limited, prejudiced or excluded by this warranty.