LITHONIA LIGHTING OLW 23 Watts LED Wall Pack Instruction Manual

LITHONIA LIGHTING OLW 23 Watts LED Wall Pack Instruction Manual

INSTALLATION INSTRUCTIONS

LED Dusk to Dawn Security Area/Wall light

Model Number

OLW 23 & OLW 31

Five year limited warranty. Full warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx

Protect yourself. Before installing, read these instructions carefully and save them for future reference.

Date Installed: ___

Failure to follow any of these instructions could void product warranties. For a complete list of product Terms and Conditions, visit www.acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.

Important Safety Instructions

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.
• For Residental installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
• DO NOT INSTALL DAMAGED PRODUCT!
• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
• Fixture can NOT be used with a dimmer switch, motion or occupancy sensors and other electronic switching devices unless otherwise designated.
• This fixture should not be used in areas with limited ventilation or high ambient temperatures.
• This fixture is intended to be connected to a properly installed and grounded UL listed junction box.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purpose, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING: RISK OF ELECTRICAL SHOCK

• Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code and any applicable local code requrirements.
• All wiring connections should be capped with UL approved wire connectors.

CAUTION: RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small pars and destroy packing material, as these may be hazardous to children.

WARNING: RISK OF BURN

• Allow fixture to cool before handling. Do not touch enclosure or light source.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all lamp manufacturer’s warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods, replacement, and recycling.
• Use only lamps that comply with ANSI standards.

CAUTION: RISK OF FIRE

• Keep combustible and other materials that can burn away from luminaire and lamp/lens.
• Minimum 90° C supply conductors.

CAUTION: RISK OF PRODUCT DAMAGE

• Never connect components under load.
• Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
• Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer packs, occupancy sensors, timing devices, or other related control devices. LED fixtures must be powerd directly off a switch circuit.
• Unless individal product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspce around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling.
• Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient temperature.
• Only use fixture in its intended location.
• LED products are Polarity Sensitive. Ensure proper Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit.
• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
• Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when used in a commercial environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instruction manual, this equipment may cause harmful interference to radio communications. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Failure to follow any of these instructions could void product warranties. For a complete list of product Terms and Conditions, visit www.acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.

Mounting Hardware Included
Silicone Sealant required

1. Remove fixture components and parts pack. Check that all parts are included.

2. Turn OFF Power at circuit breaker box.

CAUTION: Do not rely on wall switch alone to turn off power.

Note: NOT suitable for use with dimmers, motion sensors or other remote devices.

Note: This Fixture is intended for Wall mount above 6ft (1,8m) only.

This fixture is designed for multiple installation options:

3A. Installation to round or rectangular recessed and round surface mount j-box: see FigA1 & A2

Remove Mounting Plate [8] (shown in Fig C) and attach Backplate [5] (see Fig A1).
Install Crossbar [2] with Threaded Pipe [3] to standard recessed outdoor wet location junction box using two 1/2” screws [4] (see Fig A2).
Use wire nuts [9] to make wiring connections as outlined in step 4.
Push wire connections into j-box and align Backplate with the Threaded Pipe. Push Backplate close up to wall and secure with Decorative Nut [10] Note: make sure not to pinch any wires.

3B. Installation to extension arm (sold separately): see Fig B

Remove Mounting Plate [8] (shown in Fig C) and attach Backplate with Gasket [16] (see Fig B). Loosen Set Screws [11] on bottom of fixture neck. Remove access panel [14] (see Fig C) of LED Light Fixture to access wiring compartment. Note: a safety tether will temporarily hold the panel while wiring fixture.

Align hole in neck of LED Light Fixture with extension arm, thread house supply wires extending from arm through neck into fixture wiring compartment and slide LED Light Fixture onto arm being careful not to pinch any wires. Make sure fixture is level and tighten Set Screws to secure. Follow fixture wiring instructions contained in this Inst Sheet in step 4.

3C.Surface and conduit mounting: see FigC

Use Mounting plate [8] as template to mark mounting hole locations and drill 3/16” diameter pilot holes. Partially install Mounting screws (Hardware included for mounting to wood surfaces only) Note: Assure that fixture is mounted onto structurally sound surface that will support the weight of the fixture.

Remove access panel [14] Note: a safety tether will temporarily hold the panel. Thread house supply wires through Mounting plate and fixture neck or, if conduit is used, through Conduit excess hole (13) into fixture wiring compartment inside of fixture housing.

Align keyhole and slots on Mounting Plate with the three partially installed Mounting Screws and tighten the Mount ing Screws to secure fixture.

Use wire nuts to make wiring connections inside wiring compartment as outlined in instructions in step 4.

Push wire connections into fixture wiring compartment next to driver, making sure not to pinch wires between driver and access panel and re-install access panel [14].

4. CAUTION: WIRING AND FIXTURE OPERATION Note: Make sure power is turned off!

Use Wire Nut to connect the house supply ground wire ( copper ) & the fixture ground ( copper ) wire.

Note: If house wiring does not include a ground wire, consult your local electrical code for approved grounding methods.

Use Wire Nuts to connect the black fixture wire to the black power supply wire and the white fixture wire to the white ( neutral ) house supply wire.

For proper connection, place wire nut over wires and twist clockwise until tight.

5. Turn on electricity at fuse or circuit breaker box and verify success of installation.
Note: Adjust photocontol so that the window is fully open

6. Apply silicone caulking (not included) around the perimeter of the back of the fixture where it contacts the mounting surface for moisture seal.

Installation Figures

REQUIRED TOOLS

Trouble Shooting Guide

If this fixture fails to operate properly, use the guide below to diagnose and correct the problem.

If light does not come on:

• Verify that power is turned on at switch and breaker
• Verify that fixture is wired properly
• Verify that line voltage is correct.
• Test if Photocontrol works properly

The photocontrol in this fixture is designed to turn on fixture light at low light levels. During daylight installation light should come on and then go off.

If light does not come on or stays on:

Test if Photocontrol works properly:

• Cover Photocontrol – Light should come on.
• Shine a flashlight into Photocontrol – Light should go off.

If fixture cylcles on and off:

Light reflecting back off any surrounding surfaces enter the photocontol. To correct problem, adjust Photocontrol cover. If Photocontrol cover is in closed position, it will allow operation of fixture during daylight.

If further assistance is required, contact:

Technical Support at:800-279-8041

This LED light provides low maintenance service with no bulbs to change. Clean surfaces with mild soap and water. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

WARNING: There are no user serviceable parts inside fixture.

Consumer Products Group/Acuity Brands Lighting, Inc.
One Lithonia Way, Conyers, GA 30012
www.lightahome.com

References

• Acuity Brands | Lighting, Controls, and Building Management Solutions
• U.S. Environmental Protection Agency | US EPA
• Residential Lighting Resources | Industries | Acuity Brands

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>