AMPROBE TPP1-C1 Flat Surface Probe User Manual

TPP1-F1, TPP1-C1,
TPP2-F1, TPP2-C1
TPP1-F1,C1
TPP2-F2,C2
Digital Thermometers
User Manual

TPP Mini-Thermometers

Safety Information

• Do not use the thermometer if:
  • It appears to be damaged.
  • It does not carry out the desired measurement.
• When replacing the battery, make certain of the correct polarity.
• Only use batteries as described in the Specifications section.
• Use the thermometer only as specified in this manual, or the protection provided by the thermometer might be impaired.
• Thermometers must be stored in a dry and closed area. If a thermometer is transported in extreme temperatures, a 2 hour recovery time is required before use.

Warning
Shock danger. Supplied thermometer is not intended for contact with live electrical circuits.
Symbols Used in this Manual

Introduction

The Amprobe models TPP1 and TPP2 are mini-thermometers with a Negative Temperature Coefficient (NTC) sensor allowing for simple and quick temperature measurement. Both models are available in Fahrenheit and Celcius versions.
Model TPP1
Immersion thermometer for measuring the temperature in air, liquid,
or powdery materials.
Model TPP2
Thermometer with flat surface probe.
The manual contains information to allow you to safely operate and maintain the TPP series of digital mini-thermometers. Please read the manual before using the mini-thermometer.
Warning
Before making a measurement, verify that the surface to be measured is not electrically live. Failure to comply can lead to operator injury or instrument damage.
Caution
Follow the specified thermometer measurement ranges.
Caution
To avoid burns, only touch the unit under test using the measurement probe.

Making a Measurement

• Turn the thermometer on with the ON/OFF button.
• Bring the surface or material to be measured into contact with the temperature sensor.
• Wait until a steady value is displayed. The time required to obtain an accurate measurement depends on the application and may take up to 30 seconds.
• **** Hazardous temperatures maybe present at unit under test if H (HOLD) is present on display.
• You can press the HOLD button to store the measurement value. H appears in the display when the thermometer is in Hold mode.
• Before making a measurement, turn the HOLD function OFF.
• Overload or underload conditions appear as OL or -OL on the thermometer display.

For the most accurate measurement results, follow the guidelines below:

• When measuring liquid, paste, or solid material, the insertion depth of the sensor should be approximately 30 mm (1.18 in).
• For surface temperature measurement, there must be reasonable heat contact between the sensor and the surface to be measured.
  The surface and the sensor should be clean and the sensor must be place vertically on the surface. The use of a thermal conductivity paste is suggested.

Cleaning

• Turn the thermometer OFF prior to cleaning.
• Clean the thermometer using a damp cloth and household detergent.
• Never use acid detergents or solvents for cleaning.
• Do not use the thermometer until it is completely dry.

Replacing the Battery

If you can’t turn on the thermometer, or if the display is dim after you turn it on, the battery needs to be replaced.

To replace the battery

1. Pry open the upper case cover.
2. Remove the discharged battery.
3. Insert the new battery.
4. Replace the upper case cover.
   

Specifications

Humidity: Valid for 23 °C ± 5°, for less than 70% RH
Display: LCD, 3 ½ digit
Overload display: OL or -OL
Range: -50 to 250 #C (-58 to 482 #F)

-50 to -20 #C
-19.9 to 49.9 #C
50 to 199.9 #C
200 to 250 #C
-58 to -4 °F
-3.8 to 121.8 °F
122 to 391 °F
392 to 482 °F| 1.0 #C
0.1 #C
0.1 #C
1.0 #C
1.0 °F
0.1 °F
0.1 °F/1 °F
1 °F| ± 3 #C
± 2 #C
± (2% rdg +1 #C)
± (2% rdg +1 #C)
± 5 °F
± 1.8 °F
± (2% rdg + 1.8 °F)
± (2% rdg + 2 °F)

Temperature Change/response time: > 10 #K/s
Temperature Coefficient: <0.1 multiply with tolerance per #C for
environment condition 0# to 18 #C and 28# to 50 #C
Working Temperature: 0 #C to 50 #C at 80% relative humidity
Storage Temperature: 0 #C to 60 #C (32 °F to 122 °F) at RH <80%
Power supply: 3 V battery, CR 2032
Battery life: approximately 200 hours
Dimensions: 40 x 30 x 160 mm (1.57 x 1.18 x 6.29 in)
Weight: approximately 16 g (.56 oz) including battery
Pollution degree: IP40
Altitude: 2000 m (6561 ft)

Repair

All test tools returned for warranty or non-warranty repair or for calibration should be accompanied by the following: your name, company’s name, address, telephone number, and proof of purchase. Additionally, please include a brief description of the problem or the service requested and include the test leads with the meter. Nonwarranty
repair or replacement charges should be remitted in the form of a check, a money order, credit card with expiration date, or a purchase order made payable to Amprobe® Test Tools.
In-Warranty Repairs and Replacement – All Countries Please read the warranty statement and check your battery before requesting repair. During the warranty period any defective test tool can be returned to your Amprobe® Test Tools distributor for an exchange for the same or like product. Please check the “Where to Buy” section on www.amprobe.com for a list of distributors near you. Additionally, in the United States and Canada In- Warranty repair and replacement units can also be sent to a Amprobe® Test Tools Service Center.

Amprobe Test Tools
Everett, WA 98203
Tel: 877-AMPROBE
(267-7623)| Amprobe Test Tools
Mississauga, ON L4Z 1X9
Tel: 905-890-7600| European Correspondence*
Amprobe® Test Tools Europe
P.O. Box 1186
5602 BD Eindhoven
The Netherlands

*(Correspondence only – no repair or replacement available from this address. European customers please contact your distributor.)

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and workmanship for 1 year from the date of purchase. This warranty does not cover fuses, disposable batteries or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Amprobe’s behalf. To obtain service during the warranty period, return the product with proof of purchase to an authorized Amprobe Test Tools Service Center or to an Amprobe dealer or distributor. See Repair Section for details. THIS WARRANTY IS YOUR ONLY REMEDY. ALL OTHER WARRANTIES – WHETHER EXPRESS, IMPLIED OR STAUTORY – INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of liability may not apply to you.

PN 2099506
March 2007
“2007 Amprobe Test Tools.
All rights reserved. Printed in China

References

• Amprobe | Electrical Test and Measurement Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>