MONSTER Light Up Stag Instruction Manual
- June 9, 2024
- Monster
Table of Contents
MONSTER Light Up Stag
PRODUCT DESCRIPTION
The Monster Light Up Stag is a flat pack, easy to assemble, light-up reindeer
ready to bring you Christmas cheer! Our gift to you is a special timer to help
you save money and the planet!
Product Information
The Monster Light Up Stag is a flat pack, easy-to-assemble, light-up reindeer that is perfect for spreading Christmas cheer. It comes with a special timer plug that helps you save money and the planet. The stag has ice-white (24000k) LED lights that emit a beautiful glow. The stag can be used indoors and outdoors as it has an IP44 rating. The metal frame is coated in weatherproof white paint and comes with metal pegs to secure it to the ground.
Product Specifications
- LED Colour: Ice White (24000k)
- 24v Plug-in transformer
- 8m clear wire
- IP44 Indoor & outdoor use
- Metal frame coated in weatherproof white paint
- Metal pegs (included secure figure into the ground)
- Dimensions: H 110cm x W 70cm x D 19cm
Product Parts List
- Reindeer with attached legs (4x) & Tail
- Leg Bars (2x)
- Wing bolt (4x)
- Pegs (6x)
- Cable ties 8cm (50x) Approx.
- Cable ties 12cm (x25) Approx.
- UK Timer Plug. (x1)
- EU Timer Plug. (x1)
Product Usage Instructions
- Remove the packaging and check all parts are present.
- Attach the connected legs to adjacent mounting points. Line up the hole in the underside and screw in the wing bolt ensuring they are finger-tight. Repeat for each leg.
- Insert the tail, and male part into the corresponding female part. (friction fit)
- Attach the head, 4 male parts in the base of the head should fit with corresponding female parts in the body. (friction fit)
- If required, use cable ties to tidy/arrange to cable.
- Attach the power cable to UK or EU timer plug. (G) or (H)
- Plug-in.
- To set the timer, press the white button on the plug.
- First press, green light on. Lights are set ON.
- Second press, green light off. The timer is set (6 Hours ON then 18 Hours OFF).
- Third press, green light off. The lights are OFF.
- The fourth press returns to start.
SPECIFICATION
- LED Colour: Ice White (24000k)
- 24v Plug in transformer
- 8m clear wire
- IP44 Indoor & outdoor use
- Metal frame coated in weatherproof white paint
- Metal pegs (included secure figure into ground)
DIMENSIONS
- H 110cm x W 70cm x D 19cm
PARTS LIST
When first unpacking your reindeer, check each part against this list to ensure that they are all present. If any are missing contact us before attempting to assemble.
- A. Reindeer with attached legs (4x) & Tail
- B. Leg Bars (2x)
- C. Wing bolt (4x)
- D. Pegs (6x)
- E. Cable ties 8cm (50x) Approx.
- F. Cable ties 12cm (x25) Approx.
- G. UK Timer Plug. (x1)
- H. EU Timer Plug. (x1)
PRODUCT FEATURES
- A. IP44 Indoor and Outdoor use
- B. UK & EU timer plug
- C. Ice white 24000k LEDs
SAFETY ADVICE
SAFE WORKING PRACTICE
Please read through the Safe Working Practice to ensure the prevention of
injury or damage to the device.
Please ensure the plug and controller (if fitted) are plugged into the main
power supply indoors. Unless if connected to a moisture-protected power
outlet.
- Do not immerse the product in water.
- Do not use in damp conditions.
- Do not connect electrically to other light sets.
- The cable on this light set cannot be replaced, if it is damaged – then dispose of this LED set.
- Turn this product off if it starts to produce excess heat.
- Do not connect this set to the electrical supply while in its packaging.
- This product may contain a glass handle with care.
- This set is fitted with non-replaceable bulbs.
- Do not attempt to repair the product yourself, repairs should be carried out by a qualified technician.
Monster Group UK Limited’s liability will be limited to the commercial value of the product only.
ASSEMBLY INSTRUCTIONS
- Remove the packaging, and check all parts are present.
- Attach connected legs to adjacent mounting points. Line up the Hole in the underside and screw in the wing bolt (C) ensuring they are finger-tight repeat for each leg.
- Insert the tail, and male part into the corresponding female part. (friction fit)
- Attach Head, 4 male parts in the base of the head should fit with corresponding female parts in the body. (friction fit)
- If required, use cable ties to tidy/ arrange to cable.
- Attach the power cable to UK or EU timer plug. (G) or (H)
- Plugin.
- To set the timer press the white button on the plug.
- First press, green light on. lights are set ON
- Second press, green light off. The timer is set (6 Hours ON then 18 Hours OFF)
- Third press, green light off. Lights are OFF
- Forth press returns to start.
TROUBLESHOOTING
RESOLUTION GUIDE
WHAT DO I DO IF THERE ARE MISSING PARTS FROM MY ORDER?
If there appears to be any part missing from your order, contact our friendly
and helpful Customer Support Team within 7 days of receipt.
FOR ALL OTHER ISSUES, PLEASE CONTACT OUR CUSTOMER SUPPORT TEAM.
Monster Group (UK) is one of the UK’s fastest-growing online retailers. We supply a diverse range of products that offer exceptional value for money. We strive to provide the best possible customer experience with free UK delivery across all our products and a Monster Guarantee for 100% satisfaction.
For information regarding this device or other products from our Monster divisions please contact Sales.
SALES
- TEL: 01347 878 888
- EMAIL: [email protected]
For queries about this device, warranty, returns, or reporting faults please contact Support.
SUPPORT
- TEL: 01347 878 887
- EMAIL: [email protected].