MTX Audio PROXP-20-SW 5-speaker amplified audio system Owner’s Manual

: June 9, 2024
: MTX Audio

Table of Contents

THANK YOU
WE’RE HERE TO HELP
IMPORTANT NOTICE
FEATURES
SPECIFICATIONS
FIT GUIDE
IN THE BOX
DISASSEMBLY
INSTALLATION
WARRANTY PERIOD
MITEK WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MTX Audio PROXP-20-SW 5-speaker amplified audio system

THANK YOU

Thank you for making the AWESOME decision to purchase our MTX Audio direct-fit subwoofer enclosure designed for the Polaris® RZR® Pro XP. Our sub enclosure, with its high output 10″ subwoofer, will belt out the bass and deliver ground pounding audio making you the party vehicle in any ride! With a few basic hand tools in your trusty toolbox, you can have this installed in no time. So, what are you waiting for? It’s time to get the rumble in your ride and go hit the trails! Oh, and congratulations on your purchase, thanks for your support and most importantly, enjoy the ultimate audio experience with MTX!

IMPORTANT NOTICE

Whenever working on the vehicle, it is recommended to disconnect the battery prior to starting work. Failure to do so may lead to a risk of electric shock or equipment damage.

When connecting power and ground wires ensure that the red power wire is fused at the point where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the product.

FEATURES

Ported Enclosure Design Produces Louder, Deeper Bass Output
Includes an MTX 55 Series Subwoofer for its Deep Bass Reproduction Capabilities
Compatible with Existing OEM Front Speaker Enclosures
Mounts Behind Dashboard
Factory Matched Texture
Installer Friendly Design
Direct Fit, No Cutting or Drilling Required

SPECIFICATIONS

10″ Loaded Subwoofer Enclosure
RMS Power Handling: 400-Watts
Peak Power Handling: 800-Watts
Sensitivity (2.83V/1m): 90.2dB
Sensitivity (1W/1m): 83.5dB
Frequency Response: 28Hz – 130Hz
Impedance: Dual 4Ω

FIT GUIDE

Pro XP / XP4 Sport …………………………………………………………………………………………………………………2021 – 2022
Pro XP / XP4 Premium……………………………………………………………………………………………………………2020 – 2022
Pro XP / XP4 Ultimate…………………………………………………………………………………………………………….2020 – 2022
Pro XP / XP4 Sport RFLE…………………………………………………………………………………………………………………..2021
Pro XP / XP4 Ultimate RFLE ……………………………………………………………………………………………………………..2021

IN THE BOX

PROXP-20-SW Loaded Subwoofer Enclosure
Mounting Hardware
(1) Mounting Bracket
(3) M6 (10mm) Hex Head Bolts – 15mm Long
(2) T40 Torx Pan Head Bolts – 45mm Long
(8) Zip Ties

DISASSEMBLY

Step 1 – Start by removing the hood. Remove two (2) T-40 TORX bolts and lift off.

Step 2 – Remove two (2) T-40 TORX bolts located under hood securing the front of the dash.

Step 3 – Remove two (2) panel clips located under the hood securing the left and right fenders

Step 4 – Remove three (3) grey trim pieces from the front of the dash using a panel removal tool or by gently prying with a flat blade screwdriver.

One left of steering wheel

One right of steering wheel

One on passenger side

Step 5 – Remove seven (7) T-40 TORX bolts across the bottom front and top of the dash panel as indicated.

Step 6 – Remove four (4) T-20 TORX screws found under the passenger side glove box lid. This will allow the glove box to drop out from the bottom of the dash. Note: This pocket will not be reused with the subwoofer enclosure installation.

Step 7 – Open the top center storage compartment and lift out the pocket liner. Push the USB connector through the side of the pocket, freeing it and lift out of the vehicle. Note: This pocket will be reinstalled upon reassembly

Step 8 – Disengage the tweeter housing from the top of the dash panel and slide up the cag.

Step 9 – Starting on either side, lift on the fender panel to disengage the tabs that pass through the dash panel. While lifting, slide the dash panel toward the back of the vehicle freeing it from the fender. Repeat this on the other side. Once the dash panel is free lift out of the vehicle and set aside.

Step 10 – Locate and remove the under-dash tray found below the center storage pocket location by removing five (5) panel clips and two (2) T-25 TORX screws located on the firewall below the pulse connector bank. If the vehicle has the OE audio amplifier installed, disengage its harness connector, and lift the panel out.

Note: If you are installing the subwoofer enclosure as part on an MTX Thunder kit, this tray will not be reused. The kit amplifier mounting rack will replace this part.

If not installing as part of an MTX Thunder kit, the tray will need to be modified as indicated prior to reinstallation. Cut and remove the area indicated.

INSTALLATION

Step 11 – Start by installing two (2) brass colored speed clips into the indicated factory locations on the lower firewall in the passenger side footwell.

Step 12 – Locate the subwoofer mounting bracket, three (3) 10mm bolts and two (2) t-40 TORX bolts.

Step 13 – Holding the subwoofer enclosure with the MTX logo up and the woofer facing the passenger seat, install the enclosure from below by lifting and rotating the enclosure into place. The padded channel on the top of the enclosure will seat below the frame tube at the top of the dash.

Step 14 – Holding the enclosure in place, install the upper bracket in place by sliding the slots over the molded tabs at the front of the enclosure lining up the three holes with the brass inserts in the top of the enclosure.

Step 15 – Loosely install the three (3) 10mm bolts into the top of the enclosure securing the bracket in place.

Step 16 – Pressing the bottom of the enclosure against the firewall, align the mounting holes with the previously installed speed clips. Install the two (2) T-40 TORX bolts and tighten.

Step 17 – Tighten the top bolts fully to finish securing the enclosure in place.

Step 18 – If not installing as part of an MTX Thunder kit, reinstall the modified under-dash tray. Reconnect the OE amplifier if disconnected previously.

Note: If installing as part of an MTX Thunder kit, plug the subwoofer enclosure into the subwoofer harness provided in the kit.

If not installing as part of an MTX Thunder kit, the enclosure will need to be hardwired by removing the connector and following the wiring diagram below.

Speaker Wire

Red (+)
Black (–)

Once the subwoofer enclosure is connected test for function.

Step 19 – Reassemble and go ride.

WARRANTY PERIOD

At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user.

Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue. If, after speaking with our technical experts it is determined that a problem lies with the product, the technician will provide you with a Return Authorization number and all relevant details you’ll need to get the product taken care of.

MITEK WARRANTY

MiTek Mobile products (including, but not limited to: MTX, Coustic, Streetwires, Xtant, BassSlammer, and Thunder Marine) purchased in the USA from an AUTHORIZED MITEK DEALER are guaranteed against defects in material and workmanship for the period of time specified. The warranty period begins the day the product is purchased by the end user, and this warranty is limited to the original retail purchaser of product. Products found to be defective during the warranty period will be repaired or replaced with equivalent product by MiTek at no charge. This warranty is void if it is determined that unauthorized parties have attempted repairs or alterations of any nature, and the warranty does not extend to cosmetics or finish. MiTek disclaims any liability for other incurred or consequential damages resulting from product defects. MiTek’s total liability will not exceed the purchase price of the product.

Let’s Get Social
mtx.com