Baechler DS20U Series Shuttle Barebone PC User Guide
- June 4, 2024
- Baechler
Table of Contents
DS20U Series Quick Guide
More information on this product can be found at: http://bit.ly/DS20U
Product Overview
1. USB 3.2 Ports (Celeron → Gen 1, Core I → Gen 2)
2. USB 2.0 Ports
3. Power LED
4. Hard Disk Drive LED
5. Power Button
6. SD Card Reader
7. MIC-in
8. Headphones| 9. External Power SW & Clear CMOS
10. HDMI Port
11. DisplayPort
12. COM/VGA Port (RS232 only) (Option)
13. COM Port (RS232/RS422/RS485) (BIOS Setting)
14. LAN Ports (Gigabit LAN)
15. Power Jack (DC IN)
16. Connector for WLAN antenna
17. Kensington® Lock Hole
---|---
Hardware Installation
A. Begin Installation
For safety reasons, please ensure that the power cord is disconnected
before opening the case.
- Unscrew the two screws of the chassis cover. Slide the cover backward and upwards.
The product’s color and specifications may vary from the actual shipping
product.
B. HDD or SSD Installation
-
Unfasten the rack mount screw and remove the rack.
-
Place an HDD or SSD in the rack and secure it with two screws from each side.
-
Lay the HDD or SSD into its drive bay and push it gently to the right until it clicks into place. Refasten screws.
C. Memory Module Installation
This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules.
-
Locate the SO-DIMM slots on the motherboard.
-
Align the notch of the memory module with one of the relevant memory slots.
-
Gently insert the module into the slot at a 45-degree angle.
-
Carefully push down the memory module until it snaps into the locking mechanism.
-
Repeat the above steps to install an additional memory module, if required.
D. M.2 Device Installation
- Locate the M.2 key slots on the motherboard.
- Install the M.2 device into the M.2 slot and secure it with the screw.
M.2 2242/2260/2280 M key slot
E. Complete
- Please replace and affix the case cover with two screws. Turn your DS20U upside down.
- Connect the power cord.
- Complete.
Please press the “Del” key while booting to enter BIOS. Here, please load the optimized BIOS settings. Operation Position: Please make sure to use either the supplied feet or the VESA mount.
Safety Information
Incorrectly replacing the battery may damage this computer. Replace only with
the same or equivalent as recommended by Shuttle. Dispose of used batteries
according to the manufacturer’s instructions.
All bundled parts, power cord included, shall not be used without this
product.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This device meets the requirements for EU conformity in accordance with the currently valid EU directives.
Product Overview
1. USB 3.2 Ports
2. USB 2.0 Ports
3. Power LED
4. Hard Disk Drive LED
5. Power Button
6. SD Card Reader
7. MIC-in
8. Headphones| 9. External Power SW & Clear CMOS
10. HDMI Port
11. DisplayPort
12. COM/VGA Port (RS232 only) (Option)
13. COM Port (RS232/RS422/RS485) (BIOS Setting)
14. LAN Ports (Gigabit LAN)
15. Power Jack (DC IN)
16. Connector for WLAN antenna
17. Kensington® Lock Hole
---|---
Hardware Installation
A. Begin Installation
For safety reasons, please ensure that the power cord is disconnected before
opening the case.
- Unscrew the two screws of the chassis cover. Slide the cover backward and upwards.
B. HDD or SSD Installation
- Unfasten the rack mount screw and remove the rack.
- Place the HDD or SSD in the rack and secure it with two screws from each side.
- Lay the HDD or SSD into its drive bay and push it gently to the right until it clicks into place. Refasten screws.
The product’s color and specifications may vary from the actually
C. Memory Module Installation
This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules.
- Locate the SO-DIMM slots on the motherboard.
- Align the notch of the memory module with one of the relevant memory slots.
- Gently insert the module into the slot at a 45-degree angle.
- Carefully push down the memory module until it snaps into the locking mechanism.
- Repeat the above steps to install an additional memory module, if required.
D. M.2 Device Installation
- Locate the M.2 key slots on the motherboard.
- Install the M.2 device into the M.2 slot and secure it with the screw.
E. Complete
- Please replace and affix the case cover with two screws. Turn your DS20U upside down.
- Connect the power cord.
- Complete.
Please press the “Del” key while booting to enter BIOS. Here, please load the optimized BIOS settings. Operation Position: Please make sure to use either the supplied feet or the VESA mount.
Motherboard Illustration
|
---|---
01. USB 3.2 Ports (Celeron →Gen 1, Core I → Gen 2)
02. USB 2.0 Ports
03. Power LED
04. Hard Disk Drive LED
05. Power Button
06. MIC-in
07. Headphones
08. Debug Header
09. 2.5-inch HDD/SSD Slot
10. DDR4 SO-DIMM Slots| 11. Battery Connector
12. M.2 2230 E Key Slot
13. M.2 2242/2260/2280 M key slot
14. Power jack (DC IN)
15. LAN Ports (Gigabit LAN)
16. COM Port
17. DisplayPort
18. HDMI Ports
19. Intel® Celeron® / Pentium processor
20. SD Card Reader FFC Connector – CON3
---|---
Jumper Settings
J1: COM 2 Port
COM2 (RS232)
Pin| Signal Name| Pin| Signal Name
1| DCD| 2| RDX
3| TXD| 4| DR
5| GND| 6| DSR
7| RTS| 8| CTS
9| RI| |
** J2:** USB 2.0 Connector
USB5
Pin| Signal Name
1| GND
2| USB_D+
3| USB_D-
4| +5V
** J3:** AC Back Auto Power ON
JP9
Pin| Signal Name
| AM+
| GND
** J4: COM 1 & COM 2 Power Switch
COM PORT Pin 9 “Ring Indicator” (RI) configuration:
**
JP1
COM1 (pin9)| COM2 (pin9)
Short Pin| Function| Short Pin| Function
1-2 (Default)| RI1| 3-4 (Default)| RI2
7-May| +5V| 8-Jun| +5V
9-Jul| +12V| 10-Aug| +12V
** J5:** VGA connector
CN6
Pin| Signal Name| Pin| Signal Name| Pin| Signal
Name
1| GND| 2| GND| 3| SCL
4| GND| 5| SDA| 6| GND
7| GND| 8| GND| 9| VSYNC
10| GND| 11| HSYNC| 12| GND
13| GND| 14| GND| 15| BOUT
16| +5V| 17-Jan| GOUT| 18| +5V
19-Jan| ROUT| 20-Jan| +5V| |
** J6: External Power SW & Clear CMOS
**
SW2
Pin| Signal Name| Pin| Signal Name
| | 2| +5V
| | 4| RACIST-
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>