gofanco HD20Ext-LT 4K HDMI Extender Balun Over User Guide
- June 3, 2024
- gofanco
Table of Contents
gofanco HD20Ext-LT 4K HDMI Extender Balun Over
Thank you for purchasing from gofanco. Our products aim to meet all your connectivity needs wherever you go. For optimum performance and safety, please read the instructions carefully and keep this User’s Guide for future reference. If you need more information about our products, please visit www.gofanco.com. For technical support, please email us at support@gofanco.com. For drivers/manuals download, please go to www.gofanco.com/downloads.
Important Safety Notices
Please read safety instructions carefully before installation and operation.
- Please pay close attention to all warnings and hints for this device
- Do not expose this unit to rain, heavy moisture, or liquid
- Do not repair the device or open the enclosure without professional guidance to avoid electric shocks. Doing so may void your warranty
- Keep the product in a well-ventilated location to avoid damage from overheating
- Shut off power and make sure environment is safe before installation
- Do not plug the HDMI cables and IR cables in/out when the device is in use to avoid cable damage. Make sure they are plugged into the correct ports
- Use the included power adapter only. Make sure the specification matches if using 3rd-party DC power adapters
Introduction
The 4K 60Hz HDMI CAT Extender LT – 70m extends HDMI transmissions up to 70
meters over a single CAT6/6A/7 cable.
Features
- Extends HDMI transmissions up to 70m (230ft) at 4K and 1080p
- Supports UHD 4K/60Hz/4:4:4, HDR, 18Gbps bandwidth
- HDCP 2.2 compliant
- HDMI loop-out equipped on the TX, IR pass-through, 4K to 1080p auto scaling
- Supports audio extraction to Stereo on the RX
- Near zero latency
- Lightning/Surge/ESD protection
Package Contents
- 4K 60Hz HDMI CAT Extender LT – 70m (1 Transmitter & 1 Receiver)
- 1x IR Blaster cable and 1x IR Receiver cable
- 2x Power adapters (5VDC/1A)
- Surface mount accessories
- User’s guide
Installation Requirements
- HDMI source device (computer, DVD player, XBOX, PS3, etc)
- HDMI display device (SDTV/Monitor, HDTV/Monitor, projector, etc.)
- UTP/STP CAT6/6A/7 cable following IEEE-T568B wiring standard
- HDMI cables (5m max)
Product Layout
Transmitter TX Front and Rear Panel
- Reset Button: Press to reset the TX
- RJ45 Out: Connects to the Receiver’s RJ45 In using a CAT cable
- IR Out: Connects to the included IR Blaster cable to control the HDMI source device from the remote display location
- Power/Signal LED: Blinks when powered on with no HDMI signal detected, and solid on when HDMI signal is detected
- Power Jack: Connects to the included power adapter
- HDMI Out: Connects to an HDMI display for local monitoring of the remote display
- HDMI In: Connects to your HDMI source
Receiver RX Front and Rear Panel
- Reset Button: Press to reset the RX
- RJ45 In: Connects to the Transmitter’s RJ45 Out using a CAT cable
- IR In :Connects to the included IR Receiver cable to control the HDMI source device from the remote display location
- Power/Signal LED: Blinks when powered on with no HDMI signal detected, and solid on when HDMI signal is detected
- Power Jack: Connects to the included power adapter
- HDMI Out: Connects to an HDMI display
- Audio Jack: Connect to Stereo speakers or headphones
CAT Cable Wiring
We suggest both RJ45 connectors be wired identically using T568B wiring
standard for the best performance and compatibility.
Hardware Installation
- Power off all devices including your HDMI source and HDMI display(s).
- Connect your HDMI source device to the Transmitter’s HDMI In connector with an HDMI cable (HDMI cable not included).
- Optional: Connect your HDMI display to the Transmitter’s HDMI Out connector with an HDMI cable (HDMI cable not included) for local monitoring of the HDMI signal.
- Optional: Connect the IR Blaster cable to the Transmitter’s IR Out port. Face the cable’s emitter eye towards your HDMI source device’s IR window. This connection is needed only if you need to control your HDMI source device from the remote display location.
- Plug a CAT6 cable between the Transmitter’s RJ45 Out and Receiver’s RJ45 In.
- Connect your HDMI display to the Receiver’s HDMI Out connector with an HDMI cable (HDMI cable not included).
- Optional: Connect the IR Receiver cable to the Receiver’s IR In port. This connection is needed only if you need to control your HDMI source device from the remote display location.
- Plug the included power adapters into the TX’s and RX’s power jack, then plug the power adapters into reliable power sources.
- Power on all connected devices.
- The HDMI extender is ready for use.
Application Diagram
Specifications
Disclaimer
The product name and brand name may be registered trademarks of related
manufacturers. TM and ® may be omitted on the user’s guide. The pictures on
the user’s guide are just for reference, and there may be some slight
differences with the actual products.
We reserve the right to make changes without prior notice to a product or
system described herein to improve reliability, function, or design.
Thank you for choosing gofanco
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>