Hangzhou DSGW-210B Indoor LoRaWAN Gateway User Manual
- June 9, 2024
- Hangzhou
Table of Contents
Hangzhou DSGW-210B Indoor LoRaWAN Gateway User Manual
Product Information:
The Indoor LoRaWAN Hotspot (DSGW-210B) is a high-efficiency hotspot for HNT.
It supports Helium LongFi, an architecture that combines the leading wireless
LoRaWAN protocol, and Helium Blockchain technology. Helium, a global,
distributed network of Hotspots, enables everyone to contribute to a public,
long-range wireless coverage for LoRaWAN-enabled IoT devices and earn HNT
rewards by providing coverage and transferring data packets.
Product List:
| Name | Number |
|---|---|
| Gateway | 1 |
| Mounting bracket | 1 |
| Antenna | 1 |
| Expansion screw | 3 |
-
Gateway
-
Mounting bracket
-
expansion bolt * 3
-
Antenna
Download the app
How To Use
Reset the device
Press and hold the reset button on the gateway for more than 10 seconds until the green light blinks. Then the device restores to factory Settings.
Indicator Light Description
| Red light on | System startup |
|---|---|
| Red light breathing | Network disconnected |
| Blue light is always on | Network connection |
| Blinking green light (short time, then system reboot) | Reset to factory |
setting
Blue light breathing| Updating firmware
Green light circle| Upgrading miner docker image
Purple light flashing| Bluetooth advertising pairing
Installation Method
-
Place the product flat directly on a horizontal table surface.
-
you can install the brackets with Expansion screw into wall or roof, then insert the gateway.
Hotspot Settings guide and usage
Location
Find the best location for your hotspot. The general advice is to avoid placing any metal in front of the antenna and double glazed windows if possible. Avoid exposing the device to direct sunlight as this may cause it to overheat.
Power on
Install the antenna to the gateway, then power on, plug in the network cable.
It is highly recommended to use Ethernet rather than WiFi whenever possible.
-
system startup
-
Internent connect
-
Bluetooth advertising
- After connecting the power and Ethernet port, if the red light keeps on, it means the device is starting, if the red light is breathing, it means the network are disconnected, you need to check whether the network is ok.
- If the blue LED light is on, the network is connected properly.
- Enable the device into the bluetooth pairing mode by press the button on the gateway. If the LED is flashing purple.the bluetooth starts advertising and can be operated via app.
Activate your Dusun hotspot
Download the Helium and Dusun Hotspot apps on your Android or iOS smartphone.
Sign up for a Helium wallet account and log in at Dusun Hotspot.
Dashboard
- Connect the gateway with a router using WAN port.
- Connect a pc to the same router.
- Find out the IP address of the gateway in the router.
- Log in the gateway use the IP address in a browser and find the Login password in the back sticker of the product.
Risk of electric shock!
- Changes or modifications to this product may lead to malfunctionand must not happen!
- Only use the included power supply!
- Do not use this product near water. It must not be exposed to dripping or splashing water or other liquids.
- Clean with a dry cloth only.
- Service should only be conducted by qualified personnel.
Warranty Service
Product performance failure caused by non-human damage within 1 year from the dayafter you sign for the product. In the event of product quality problems, our company will provide free warranty service according to the fault situation.
| Item | Technical Specification |
|---|---|
| CPU | Quad-core Cortex-A53 |
| Power Supply | USB type-C 5V/3A |
| Supported protocols | Wi-Fi / BLE / LoRaWAN |
| Indicator LEDs | RGB |
| RAM | 2GB |
| ROM | eMMC 32GB |
| System | Linux |
| Security module | ATECC608 |
| Cooling | Heat dissipation silicone/aluminum |
| Working Environment | Operation Temperature: 0℃~65℃ **Storage |
Temperature: -40℃~70℃ Operation humidity: 10%~90%
RHStorage humidity:** 5%~90%RH
FCC Statement
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC RF exposure requirements,a minumum seqaration distance of 20 cm must be maintained between the user’s body and the transmitter.