Hangzhou Sky Lighting A19RGBCWKIT LED Lamp Installation Guide
- June 4, 2024
- Hangzhou Sky Lighting
Table of Contents
A19RGBCWKIT LED Lamp
Installation Guide
A19RGBCWKIT LED Lamp
FCC/ ISEDC Radiation Exposure Statement
This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter. Cet
Oquipernent dost etre instal§ et utilise avec un minimum de 20cm de distance
entre le radiateur et votre corps. Cet emetteur ne doit pas etre co-localises
ou fonctionner en conjunction avec une autre antenne ou emetteur.
SMART
LED BULB
Environmental Specification:
Only install in operating environments between -20’C and + 40°C (-4°F
and104’F).
Federal Communication Commission Interference Statement
This device complies with part 15 of the FCC Rules. The operator is stilled to
the following two conditions: (1) Ths device may not cam harmful interference.
and (2) this device must accept any interference reserved. including
interference that may cause undesired operation. This equipment has been
tested and found to comply with the knits for a Class B digital device,
pursuant to part 15 of the FCC Rules, These knits are designed to provide
reasonable protection against harmful Interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and. if not installed and used n accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and recorder.
- Connect the equipment into a cutlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: My Changes Of modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISEDC RSS Warning
This device complies with the Innovation, Science and Economic Development
Canada Compliance license-exempt RSS standard (s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may
cause undesired operation of the device.
Le present appareil est conforme aux CNR d’Innovation, Sciences et
Developpement economique ISEDC applicables aux apparel’s radio exempts de
licence. L’exploitation est autorisee aux deux conditions suivantes: (1)
fappareil ne dal pas produire de brouillage, et (2) futilisateur de Peppered
dolt acceptor tout brouillage radioelectnque sub’. memo si le brouillage est
susceptible den compromettro le fonctionnement.
LED LAMP
DOWNLOAD AND INSTALL THE FELT ELECTRIC APP
- Search for the Foil Electric App on the App Store or Google Play Store.
- Download and install the Fen Beane Apo on your smart device.
- Setup an account or login to your existing account
INSTALL YOUR LIGHT BULB
- install Constant power to the is required all time
ADD YOUR SMART WIN BULB USING THE FElT ELECTRIC APP
- Tap + in the upper right corner. Note: if this is the first device you are setting up you can also select Add Deuce
- Tap Lighting and select Lighting device (8).
- Power On the bulb(SI and confirm the buns is Oinking. Then tap Confirm (Ci.
- You MI be prompted to confirm your NW network and enter your password. Then tap Confirm ID).
STATUS MENU
- The status menu will appear. Wail until itS completed.
Note. If unsuccessful the failed to add screen will appear . close the app and repeal the previous step. if successful, continue to step 5
NAMING DEVICES
To name the bulb(si tap me Pen Icon enter IN! new name and tap Done. The to. lb: si is non-react. to be controlled with the Fen Electric App.
For a full user guide and setup instructions, please visit www.felt.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>