YAMAHA SFP-SWRT-SR/SFP-SWRT-LR Switch Owner’s Manual
- June 6, 2024
- Yamaha
Table of Contents
YAMAHA SFP-SWRT-SR/SFP-SWRT-LR Switch Owner's Manual
Owner’s Manual
General Specifications
1 Product performance may not meet specifications if the optical fiber or fitting are insufficient.
2 The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file.
Introduction
Thank you for your purchase of switch accessory SFP-SWRT-SR/SFP-SWRT-LR. This product is an SFP+ module that, when connected to the SFP+ port of a Yamaha network device, allows the use of 10GBASE-SR/10GBASE-LR. Be sure to read this Owner’s Manual before use and keep it in a safe place after reading it.
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe place for future reference.
WARNING : Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short- circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
- Before installing this product in a device, check to make sure that the device is compatible with this product. Also, do not install this product in any Yamaha products not specified by Yamaha for use with this product to prevent electrical shock, fire, or damage to the product(s).
- Do not attempt to disassemble or modify this product. Do not apply excessive force to connectors. Doing so may cause electrical shock, fire, or damage to the product(s).
- Do not place any burning items or open flames near the device, since they may cause a fire.
CAUTION : Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following:
- Be sure to properly ground the host device to prevent electrical shock, fire, or damage to the product(s).
- Do not place the product in a location where it may come into contact with corrosive gases or salt air. Doing so may cause damage to the product(s).
- Do not look at the laser light. This product uses a laser. Be careful to avoid looking at the ends of the optical fibers or the optical connectors. In the event you look at the laser, it may damage your eyes.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.
Handling and maintenance
Clean the equipment regularly by using commercially available optical fiber cleaning products. Correct communication might not be possible if debris and/or dust has adhered to the ends of optical fiber cables or the ports.
Do not expose the product to excessive dust or vibration, or extreme cold or heat, in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components.
Do not install in locations where temperature changes are severe. Otherwise, condensation may form on the inside or the surface of the product, causing it to break.
Do not place vinyl, plastic or rubber objects on the product, since this might discolor the panel.
When cleaning the product, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.
Drain all static electricity from your clothing and body before handling this product. Static electricity can damage this product. Touch an exposed metal part of the host device or other grounded object beforehand.
Do not drop this product or subject it to physical shock as this can result in breakage and/or malfunction.
Information
About functions/data bundled with the product
This is a class A product. Operation of this product in a residential environment could cause radio interference.
This product is a class 1 laser product. It is compliant with IEC/EN 60825-1,
IEC/EN 60825-2,
FDA 21 CFR 1002.10, and 1040.10.
IEC 60825-1:2014
Factory: Axcen Photonics Corporation
6F., No.119, Baozhong Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
About this manual
The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
About disposal
This product contains recyclable components. When disposing of this product, please contact the appropriate local authorities.
Information for users on collection and disposal of old equipment:
This symbol on the products, packaging, and/or accompanying documents means
that used electrical and electronic products should not be mixed with general
household waste.
For proper treatment, recovery and recycling of old products, please take them
to applicable collection points, in accordance with your national legislation.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact
your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union :
This symbol is only valid in the European Union. If you wish to discard these
items, please contact your local authorities or dealer and ask for the correct
method of disposal.
FCC INFORMATION (U.S.A.)
-
IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
-
IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. -
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
(class A)
COMPLIANCE INFORMATION STATEMENT
(Supplier’s declaration of conformity procedure)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave. Buena Park CA90620
Telephone : 714-522-9011
Type of Equipment : SWITCH ACCESSORY
Model Name : SFP-SWRT-SR, SFP-SWRT-LR
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received including interference that may cause undesired operation.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
CAN ICES-3 (A)/NMB-3(A)
(can_a_02)
Manual Development Group
© 2020 Yamaha Corporation
Published 06/2021
YJOD-B0
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>