Edge-core AS7946-30XB Aggregation Router User Guide
- June 4, 2024
- Edge-core
Table of Contents
Edge-core AS7946-30XB Aggregation Router
Package Contents
- AS7946-30XB
- Rack mounting kit — 2 rack-rail assemblies and 20 screws
- Console cable — RJ-45 to D-Sub
- Documentation — Quick Start Guide (this document) and Safety and Regulatory Information
Overview
-
4 x 400G QSFP-DD
-
22 x 100G QSFP28
-
4 x 10G/25G SFP28
-
Timing ports: 3 x RJ-45 BITS ports,1 x RJ-45 1PPS/ToD port, 1 x
1PPS connector, 1 x 10MHz connector -
USB port
-
RJ-45 Management port
-
Air filters
-
Reset button
-
Console ports: 1 x Micro-USB, 1 x RJ-45
-
Product tag
-
DC terminal or AC power socket
-
Grounding point
-
5 x fans
Front LEDs
- QSFP-DD Port LEDs:
- LED1 (top) — Cyan (400G), Blue (100G)
- LED2 (bottom) — Blue (all lanes linked), Red (not all lanes linked), Blinking (activity)
- QSFP28 Port LEDs:
- LED1 (left) — Blue (100G), Green (40G)
- LED2 (right) — Blue (all lanes linked), Red (not all lanes linked), Blinking (activity)
- SFP28 Port LEDs:
- Blue — 25G
- Green — 10G
- System LEDs:
- DIAG — Green (OK), Amber (fault detected)
- LOC — Flashes Amber when the command is activated
- FAN — Green (OK), Amber (fault)
- PS0 and PS1 — Green (OK), Amber (fault)
- Management Port LEDs:
- RJ-45 OOB Port — Left (link), Right (activity)
FRU Replacement
- Remove the power cord.
- Press the release latch and remove the PSU.
- Install replacement PSU with matching airflow direction.
Fan Tray Replacement
- Press the release latch in the fan tray handle.
- Pull out to remove the fan.
- Install replacement fan with
matching airflow direction.
Air Filter Replacement
Air Filter Replacement
- Unscrew the filter cover captive screws.
- Remove the old filter and install a replacement filter.
- Replace the filter cover and tighten the captive screws.
Warning: For a safe and reliable installation, use only the accessories and screws provided with the device. Use of other accessories and screws could result in damage to the unit. Any damages incurred by using unapproved accessories are not covered by the warranty.
Caution : The device must be installed in a restricted-access location.
Note : The drawings in this document are for illustration only and may
not match your particular model.
- Mount the Device
- Separate the rack-rail assembly into two sections.
- Use the included ten screws to attach the bracket to each side of the device.
- Slide the device into the rack.
- Hold it in place and secure the rack-assembly to the front post using four screws.
- While holding the device in place, slide the inner section of rack-rail assembly from the back until it fits the rear post.
- Secure the rack-rail assembly to the rear using four screws.
installation
Ground the Device
Attach Grounding Wire
Attach a lug (not provided) to a #8 AWG minimum grounding wire (not provided),
and connect it to the grounding point on the device rear panel. Then connect
the other end of the wire to rack ground.
Caution: The device must be installed in a restricted-access location. It
should have a separate protective ground terminal on the chassis that must be
permanently connected to a well grounded chassis or frame to adequately ground
the device chassis and protect the operator from electrical hazards.
Connect Power
DC Power
Install two DC PSUs and then connect them to a DC power source.
Caution: Use a IEC/UL/EN 60950-1 and/or 62368-1 certified power supply to
connect to a DC converter.
Note: Use # 8 AWG/ 6 mm2 copper wire (for a -40 to -75 Vdc PSU) to
connect to a DC PSU.
- Use the ring lugs included with the DC PSU.
- DC return
- -40 – -75 VDC
- Use a 8 AWG green/yellow ground wire to ground the DC PSU.
AC Power
Install two AC PSUs and then connect them to an AC power source.
Connect Timing Ports
RJ-45 BITS
Use a Cat. 5e or better twisted-pair cable to synchronize the device.
RJ-45 1PPS/ToD
Use a Cat. 5e or better twisted-pair cable to connect the 1-pulse-per-second
(1PPS) and Time of Day to other synchronized devices.
10MHz IN/1PPS OUT
Use coax cables to connect the 10MHz IN and 1-pulse-per-second (1PPS) OUT
ports to other synchronized devices.
Make Network Connections
400G QSFP-DD Ports
Install transceivers and then connect fiber optic cabling to the transceiver
ports.
The following transceivers are supported in the QSFP-DD ports:
- 400GBASE-SR8, DR4, FR4
Alternatively, connect DAC cables directly to the QSFP-DD slots.
100G QSFP28 Ports
Install transceivers and then connect fiber optic cabling to the transceiver
ports.
The following transceivers are supported in the QSFP28 ports:
- 100GBASE-SR4, LR4, CWDM4, DR1
- 40GBASE-SR4, LR4
Alternatively, connect DAC cables directly to the QSFP28 slots.
SFP28 Ports
Install transceivers and then connect fiber optic cabling to the transceiver
ports.
The following transceivers are supported in the SFP28 ports:
- 25GBASE-SR, LR
- 10GBASE-SR, LR, ER, ZR
Alternatively, connect DAC/AOC cables directly to the SFP28 ports.
Make Management Connections
MGMT RJ-45 Port
Connect Cat. 5e or better twisted-pair cable.
RJ-45 Console Port
Connect the included console cable and then configure the serial connection:
115200 bps, 8 characters, no parity, one stop bit, 8 data bits, and no flow
control.
Micro-USB Console Port
Connect using a standard USB to Micro-USB cable.
Hardware Specifications
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>