joie Spin 360TM Child Restraint Instruction Manual

joie Spin 360TM Child Restraint

Welcome to Joie™
Congratulations on becoming part of the Joie family! We are so excited to be part of your journey with your little one. While traveling with the Joie spin 360TM child restraint you are using a high quality, fully certified safety Group 0+/1 child restraint. Please carefully read this manual and follow each step to ensure a comfortable ride and best protection for your child.
If vehicle is equipped with ISOFIX, the vehicle lower anchor points may be visible at the vehicle seat crease. See your vehicle owner’s manual for exact locations, anchor identification, and requirements for use.
To use this child restraint with the ISOFIX connections according to the CNS 11497 and UN ECE R44.04 Regulation, the child should weigh under 18kg (approximately 4 years old or under).

Base
Please read all the instructions in this manual before installing and using the product.

IMPORTANT : KEEP FOR FUTURE REFERENCE. PLEASE READ CAREFULLY.
Please keep the instruction manual in the storage compartment at the bottom of the base as right figure.

Parts List

1. Head Support
2. Seat Pad
3. Buckle
4. Adjustment Webbing
5. Recline Adjustment Button
6. Load Leg
7. Load Leg Indicator
8. Load Leg Adjustment Button
9. Rotating Button
10. Shoulder Strap
11. Infant Insert
12. Head Support Adjustment Lever
13. ISOFIX Connector
14. ISOFIX Adjuster Button
15. ISOFIX Guides

Please make sure there are no missing parts. Please contact the retailer if anything is missing.

WARNING

• The child should weight under 18kg (approximately 4 years old or under).
• DO NOT use forward facing mode when the child is under 2 years old, It is still advisable to use rearward facing mode when the child is over 2 years old.
• Any straps holding the restraint to the vehicle should be tight, that any straps restraining the child should be adjusted to the child’s body, and that straps should not be twisted.
• After your child is placed in this child restraint, thesafety belt must be used correctly, and ensure that any lap strap is worn low down, so that the pelvis is firmly engaged.
• The child restraint should be changed when it hasbeen subject to violent stresses in an accident. An accident can cause damage to the child restraint that you cannot see.
• Concern the danger of making any alterations or additions to the device without the approval of the Type Approval Authority, and a danger of not follow-ing closely the installation instructions provided by the child restraint manufacturer.
• Please keep this child restraint away from sunlight, otherwise it may be too hot for the child’s skin.
• Child is not left in the child restraint system unattended.
• Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured.
• The child restraint shall not be used without the soft goods.
• The soft goods should not be replaced with any other than the one recommended by the manufacturer, because the soft goods constitutes an integral part of the restraint performance.
• DO NOT use another manufacturers soft goods with this child restraint. See your retailer for Joie replace-ment parts only.
• DO NOT use any load bearing contact points other than those described in the instructions and marked on the child restraint.
• NO child restraint can guarantee full protection from injury in an accident. However, proper use of this child restraint will reduce the risk of serious injury or death to your child.
• DO NOT install or use this child restraint without following the instructions and warnings in this manual or you may put your child at serious risk of injury or death.
• DO NOT use this child restraint if it is damaged or has missing parts.
• DO NOT have your child in swaddled clothes when using this child restraint in rear facing or forward facing mode, because this may prevent your child from being properly and securely fastened by the shoulder harnesses and the harnesses between thighs.
• DO NOT leave this child restraint unsecured in your vehicle because an unsecured child restraint can be thrown around and may injure occupants in a sharp-turn, sudden stop, or collision. Remove it if not in regular use.
• NEVER install this child restraint on any vehicle seat equipped with safety airbags when used in rear facing mode.
• NEVER use a second-hand child restraint or a child restraint whose history you do not know because they may have structural damage that endangers your child’s safety.
• DO NOT use this child restraint as a regular chair as it tends to fall down and could injure the child.
• DO NOT put anything other than the recommended soft goods in this child restraint.
• DO NOT carry this child restraint with a child in it.
• Do not allow the child restraint harness or buckles to become trapped or caught in the vehicle seat or door.
• Remove this child restraint from the vehicle seat when it is not in use for a long period of time.
• To avoid suffocation, remove plastic bag and packaging materials before using this product. The plastic bag and packaging materials should then be kept away from babies and children.
• Consult the retailer for issues concerning mainte-nance, repair and part replacement.
• Do not place any objects in the load leg area in front of your base.
• DO NOT install this child restraint on the front vehicle seat.
• Frequently check the ISOFIX guides for dirt and clean them if necessary. Reliability can be effected by ingress of dirt, dust, food particles etc.
• DO NOT install this child restraint under the following conditions:
  •  Vehicle seats with lap belt or 3-point-belt.
  • Vehicle seats facing sideways or rearward with respect to the running direction of the vehicle.
  • Vehicle seats movable during installation.

Emergency
In case of emergency or accidents, it is most important to have your child taken care of with first aid and medical treatment immediately.

Product Information

For Installation with ISOFIX System

1. This is an ISOFIX CHILD RESTRAINT SYSTEM. It is approved to CNS 11497 and UN ECE 44, 04 series of amendments for general use in vehicles fitted with ISOFIX anchorages systems.
2. It will fit vehicles with positions approved as ISOFIX positions (as detailed in the vehicle handbook), depending on the category of the child restraint and of the fixture. If in doubt, consult either the infant child restraint manufacturer or vehicle manufacturer.
3. The ISOFIX size class for which this device is intended is B1,C,D.

Allison Baby UK Ltd.
Venture Point, Towers Business Park, Rugeley, Staffordshire, WS15 1UZ

• Product spin 360TM child restraint

• Model C1416, C1416E, C1416EC

• Suitable for Child weighing under 18kg (approximately 4 years old or under)

• Materials Plastics, metal, fabrics

• Mass Group 0+/I

• Net Weight 11.95kg

• Product Size 640mmx455mmx550-785mm

• Date Please see detailed date on label (year / month / day)

• Patent No. Patents pending
  Made in China

• Distributor Chickabiddy Co. Ltd

• Address 5th FL 186 Nanking E. Rd Sec. 4 Taipei Taiwan 10595

• Tel. 0800-001-256 / 02-25781188

• Website www.chick.com.tw

Concerns on Installation

see images 1 – 2

Choose the Installation Mode

Installing the Base

see images 3 – 12

1. After placing the base on the vehicle seat, pull the load leg downward to floor. (Fig. 3)

2. Insert ISOFIX guides to assist with installation. (Fig. 4.1)

3. Press the ISOFIX adjuster button to extend the ISOFIX. (Fig. 5.1)(Fig. 5.2)

4. After aligning the ISOFIX connector with the ISOFIX Guide, hold the ISOFIX connector with single hand, insert the connector into the ISOFIX hook which hung on the seat, operate one side at a time. (Fig. 5.3)

! Make sure that both ISOFIX connectors are securely attached to their ISOFIX anchor points. The colors of the indicators on the both ISOFIX connectors should be completely green. (Fig. 6.1)
! Check to make sure the base is securely installed by pulling on the both ISOFIX connectors.

5. After attaching the ISOFIX, pull the load leg downward to floor (Fig. 7) When the load leg indicator shows green, the load leg is installed correctly. (Fig. 8)
   ! The load leg has multiple positions. When the load leg indicator shows red this means the load leg is in the wrong position.
   ! Make sure the load leg is in full contact with the vehicle floor pan. Red means it is installed incorrectly.
   ! Squeeze the load leg releasing button, then adjust the load leg length.
   ! Always make sure the support load leg has direct contact with the floor and is in locked position even when the child is not in it.

6. The completely assembled base is shown as (Fig. 9)
   ! The ISOFIX connectors must be attached and locked onto the ISOFIX anchor points. (Fig. 9.1)
   ! The load leg must be installed correctly with green indicator.(Fig. 9.2)

7. Please refer to rear facing mode and recline positions mode in section to use the child restraint.

8. To remove from the vehicle press the ISOFIX adjuster button
   (Fig. 10.1) and pull the base back from the seat. (Fig. 10.2)

9. Then press and release the connectors from the vehicle’s ISOFIX. (Fig. 11)

10. Transit to prevent damage during. Press the ISOFIX adjuster button (Fig. 12.1) and fold the connector completely.(Fig. 12.2)

Recline Adjustment

see images 13 – 14
Squeeze the recline adjustment button (Fig. 13), to adjust the child restraint to the proper position. The recline angles are shown as (Fig. 14)

Please recheck the load leg position after reclining.

Limit to use the most reclined position (1st position) with rear facing mode.
There are 5 recline positions for forward facing mode. (Fig. 14)

Height Adjustment

for Head Support and Shoulder Harnesses

see images 15 – 17

1. Please adjust the head support and check if the shoulder harnesses are at the correct height according to (Fig. 15)
   ! When used rear-facing and forward facing, the shoulder harness height must be even with or just above the child’s shoulders. (Fig. 15)

2. Squeeze the head support adjustment lever (Fig. 16.1), meanwhile pull up or push down on the head support until it snaps into one of the 6 positions. The head support positions are shown as (Fig. 17).

Using in the Rear Facing Mode

(Rearward Facing Mode/for Child under 18kg /infant – 4 years old)
Reference age Newborn – 4 years old
Recline position Limit to use the first position

see images 3 – 9

Please install the child restraint on the rear vehicle seat and then put the child in the child restraint.

see images 18 – 27

1. Press the ISOFIX adjuster button (Fig. 18.1) and pull the base back from the vehicle seat. (Fig. 18.2)
2. Press the rotating button to rotate for easier side loading/unloading of the child, then rotate back to desired direction. (Fig. 19) (Fig. 21)
3. If a tighter install or increased cabin space is required, then press the ISOFIX adjuster button (Fig. 20.1) and push to adjust. (Fig. 20.2)
4. Install the child restraint in the rear facing mode as (Fig. 21)
   ! The ISOFIX connectors must be attached and locked onto the ISOFIX anchor points. (Fig. 21.1)
   ! The load leg must be installed correctly with green indicator.
   (Fig. 21.2)
   ! Always make sure the seat is in locked position (rearward facing /forward facing) even when the child is not in it.

Securing Child
After the child is placed into the seat, check whether the Shoulder Harness Straps are at proper height.

1. Press the webbing adjustment button, while pulling out the shoulder harnesses to the proper length. (Fig. 22)
2. Unlock the buckle of the harnesses by pressing the red button. (Fig. 23)
3. Fix the buckles on the both sides of seat to make placing the child in rear facing mode more convenient. (Fig. 24)
4. Use Infant insert is for children’s protection. (Fig. 25)

5. Place the child into the child restraint and pass both arms through the harnesses.
   After the child is seated, recheck whether the shoulder harnesses are at the proper height.

6. Engage the buckle. Please refer to (Fig. 26)

7. Pull down the adjustment webbing and adjust it to the proper length to make sure your child is properly secured. (Fig. 27)
   Make sure the space between the child and the Shoulder Harness Straps is about the thickness of one hand.

8. If steps (Fig. 22) (Fig. 23) (Fig. 24) are taken when arriving at your destination whilst removing the child, then the harness will be positioned so that it is out of the way and ready for loading upon your return to the vehicle.

Using in the Forward Facing Mode

(Forward Facing Mode/for Child between
9-18kg / 2 -4 years old)
Reference age 2 – 4 years old
Recline position Position 1-5

see images 3 – 9

Please install the child restraint on the vehicle seat, and then put the child in the child restraint.

see images 28 – 35

1. Press the ISOFIX adjuster button (Fig. 28.1) and pull the base back from the vehicle seat. (Fig. 28.2)

2. Press the rotating button to rotate for easier side loading/unloading of the child, then rotate forwards to desired direction. (Fig. 29) (Fig. 31)

3. If a tighter install or increased cabin space is required, then press the ISOFIX adjuster button (Fig. 30.1) and push to adjust.(Fig. 30.2)

4. Install the child restraint in the forward facing mode as (Fig. 31)
   ! The ISOFIX connectors must be attached and locked onto the ISOFIX anchor points. (Fig. 31.1)
   ! The load leg must be installed correctly with green indicator.
   (Fig. 31.2)
   ! Always make sure the seat is in locked position (rearward facing /forward facing) even when the child is not in it.

Securing Child
After the child is placed into the seat, check whether the Shoulder Harness Straps are at proper height.

1. Press the webbing adjustment button, while pulling out the shoulder harnesses to the proper length. (Fig. 32)

2. Unlock the buckle of the harnesses by pressing the red button. (Fig. 33)

3. Fix the buckles on the both sides of seat to make placing the child in forward-facing mode more convenient. (Fig. 34)
   When installing the child restraint in the forward-facing mode, do not use the infant insert.

4. 4. Place the child into the child restraint and pass both arms through the harnesses.
   ! When used rear-facing and forward facing, the shoulder harness height must be even with or just above the child’s shoulders. (Fig. 15)

After the child is seated, recheck whether the shoulder harnesses are at the proper height.

5. Engage the buckle. (Fig. 26)

6. Pull down the adjustment webbing and adjust it to the proper length to make sure your child is properly secured. (Fig. 35)
   Make sure the space between the child and the Shoulder Harness Straps is about the thickness of one hand.

7. If steps (Fig. 32) (Fig. 33) (Fig. 34) are taken when arriving at your destination whilst removing the child, then the harness will be positioned so that it is out of the way and ready for loading upon your return to the vehicle.

Detach Soft Goods

see images 36 – 43

1. Press the red button to disengage the buckle. (Fig. 36)
2. Follow steps (Fig. 37) – (Fig. 43) to detach soft goods.
3. To re-attach the soft goods please repeat the above steps in the reverse step.

Care and Maintenance

• After removing the wedge from the insert please store it somewhere that the child cannot access it.
• Please wash the seat cover and inner padding with cold water under 30°C.
• Do not iron the soft goods.
• Do not bleach or dry clean the soft goods.
• Do not use undiluted detergents gasoline or other organic solvent to wash the child restraint or base. It may cause damage to the child restraint.
• Do not wring out the seat cover and inner padding to dry. It may leave the seat cover and inner padding with wrinkles.
• Please hang dry the seat cover and inner padding in the shade.
• Please remove the child restraint and base from the vehicle seat if not in use for a long period of time. Put the child restraint in a cool, dry place where your child cannot access it.

Share the joy at joiebaby.com

References

• Baby Gear That Goes Above & Beyond | Joie
• 奇哥 online store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>