iCOM VE-PG3 Radio Over IP Gateway Instructions
- June 9, 2024
- ICOM
Table of Contents
VE-PG3 Radio Over IP Gateway
Instructions
VE-PG3 Radio Over IP Gateway
Pin No.| Symbol| VO| Name of port| Remark| Spec.|
---|---|---|---|---|---|---
I| OPF| I| Customized input| Active in low| Less than I.15V to active the
port. Necessary wiring 3.1V 10k Pull UP.| C4
2| RTS| 0| Request To Send port| Hardware flow control to require
transmitting| 5.0V 47k Q Pull UP
3| CTS| I| Clear To Send port| Hardware flow control to receive acknowledge
for allowance of transmission| 5.0V 47k Q Pull UP| C3
4| GND| –| GND| GND (separation with ground of MIC)| GND| B4
5| AFO-| 0| AF BTL – (Output)| port for AF BTL Amp (AB class Amplifier)| AF
output 8Q load 1.0W @ 5% typ| A3
6| AFO+| 0| AF BTL + (Output)| +port for AF BTL Amp (AB class Amplifier)| AF
output 8Q load 1.0W 4 5% typ
7| 5V| 0| 5.0V DC output| 5V output from the radio| 5.0V less than 0.15A ci.10
25°C
8| MDET| I| Detection of external device| Detection for connecting external
device in some cases below.
GND with speaker mic in case, open for programing in case, 10k Q with VOX
headset in case, 4.7kQ with earphone.| –|
9| MICE| –| MIC GND| GND of MIC| –| A2,AI1
10| NC| | No Connection| –| –
11| RXD| I| Serial Data Input| Data input for programing software, PC
commands| 5.0V 47k Q Pull UP| Cl
12| TXD| 0| Serial Data Output| Data output for programing software, PC
commands| 5.0V 47k Q Pull UP| C2
13| MIC| I| MIC Input| Input for external MIC| Impedance (Input) 2.2k Q
15mVrms *S! 60%Dev| Al
14| PTT| I| PTT| External PTT, Active in Low| 3.1V 47kQ Pull UP| B1
VE-PG3/4
| Pin No. | Description |
|---|---|
| Al | Analog audio output (From the VE-PG4) / Superimpose PTT |
| A2 | Analog GND |
| A3 | Analog audio input (To the VE-PG4) / Superimpose squelch detection |
| A4 | Analog GND |
| El | General control output / Single PTT control i Relay output |
| B2 | Serial communication (Half duplex) / 8 V power supply / Relay output |
| 63 | General control input / Single squelch control |
| B4 | Common GND |
| Cl | Serial communication TXD (From the VE-PG4) |
| C2 | Serial communication RXD (To the VE-PG4) |
| C3 | Serial communication RTS (From the VE-PG4) |
| C4 | Serial communication 01-5 (To the VE-PO4) |
**** You can change the configuration of ports B1 to 64 on the VE-PG4 setting screen.
Icom America Inc. ©2020
Documents / Resources
| iCOM
VE-PG3 Radio Over IP
Gateway
[pdf] Instructions
VE-PG3, VE-PG4, VE-PG3 Radio Over IP Gateway, Radio Over IP Gateway, Over IP
Gateway, IP Gateway
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>