iCOM AH-38 Satellite Antenna Instructions

iCOM AH-38 Satellite Antenna

EXPLICIT DEFINITIONS

DISPOSAL

The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the Eu ropean Union, all electrical and electronic pro ducts, batteries, and accumulators (rechargeable batteries) must be taken to designated collection locations at the end of their wo rkin g life . Do not dispose of these products as unsorted municipal waste . Dispose of them according to the laws in your area.

ABOUT CE

Versions of the AH-38 which have the “CE” symboJ on the product comply with the essential requirements of the 2001 /95/ EC directive for General Product Safety.

lcom is not responsible for the destruc tion , d?mage t <;>, **or performance of any lcom or non-l com equipment, 1f the malfunction is because of:**

• Force majeure, including, but not limited to, fires, earthquakes, storms. floods, lightning, other natural disasters. disturbances. riots, war, or radioactive conta mination .
• The use of lcom antennas with any equipment that 1s not manufactured or approved by lcom.

PRECAUTIONS

• WARNING HIGH RF VOLTAGE! NEVER touch an antenna or antenna connector while transmitting. This could cause an electrical shock or burn.
• A WARNING HIGH RF VOLTAGE! NEVER install the antenna at any place that person easily touch the antenna while transmitting. This could cause an electrical shock or burn.
• A WARNING NEVER disassemble, modity or repair the antenna. This may result in an electrical shock, cause a fire or damage the antenna.
• WARNING! NEVER touch the antenna with wet hands This may result in an electrical shock or damage the antenna.
• CAUTION: DO NOT put the antenna in any unstable place, such as on a slanted surface or a place that vibrates. This may cause an injury and/or damage the antenna.
• CAUTION: DO NOT use the antenna in strong magnetic fields or in an area with high static electricity. This could damage the antenna.
• CAUTION: DO NOT use harsh solvents such as benzine or alcohol to clean the antenna, as they can damage the antenna’s surfaces. If the antenna becomes dusty or dirty. wipe it clean with a dry, soft cloth
• CAUTION: The antenna meets IP67 requirements for dust-tight and waterproof protection. However, once the antenna has been dropped, dust-tight and waterproof protection cannot be guaranteed because of possible damage to the antenna’s case or the waterproof seal.
• DO NOT place or leave the antenna in excessively dusty environments

Below statement is for UKCA purpose only United Kingdom Aut horised Importer.
lcom (UK) Ltd.
Address: Blacksole House, Altira Park, Herne Bay, Kent, CT6 6GZ, U.K .

SUPPLIED ACCESSORIES

• V-bolt: 2
• Nu: 4
• Flat-Washer: 4
• Angle: 1
• Rubber vulcanizing tape: 1

learn and the learn logo are registered trademarks of lcom Incorporated (Japan) in Japan, the United Stales, the United King dom, Germ any, France, Spain, Russia, Australia, New Zealand, an d/or other countries.

OPTION

OPC-2113 COAXIAL CABLE (10 m, 32 feet)

SPECIFICATIONS

• Frequency range.
  • 1575 4 ~ 1626.5 MHz
• Antenna impedance:
  • 50 © nominal
• Operating temperature range
  • -30°C ~ +60°C
• VSWR
  • -22°F ~ +140°F
• Dimensions (Projections not included)
  • 160 (d) × 80.5 (H) mm
• Weight (approximate):
  • 160 (d) × 80.5 (H) mm
• Connector:
  • 350 g, 0 77 Ib
• Maximum 1.7
  • N-J

INSTALLING THE ANTENNA

You can install the AH-38 on a 32 mm (1.3 inch) diameter pole using the included V-bolts, nuts, and flat-washers.

• Install the antenna in a place with a clear view of the sky.
• Confirm no other antennas are placed within 10 m (32 feet)
• Do not tilt the antenna. Keep the antenna pole vertical to the ground

Installation example:
Coaxial cable with Type-N and SMA connectors for the AH.38

About the antenna position:
Install the AH-38 in a place with a clear view of the sky. Make sure that there are no obstacles, such as buildings or trees, at higher than about 8 degrees around the antenna.

CONNECTION

Connect the antenna, coaxial cable, and satellite transceiver, as shown below.

1. Firmly insert the coaxial cable (purchase separately) into the connector of the antenna, and then tighten the connector clockwise.
2. Wrap the antenna connector with the supplied Rubber vulcanizing tape. This will help to prevent water seepage
   • Wrap electrical tape (user supplied) over the rubber vulcanizing tape to secure waterproofing

NOTE: If you use a coaxial cable other than the OPC- 2113, confirm that the cable has no more than 3.4 dB of attenuation at 1.5 GHz. Ask your dealer for details.

American Communication Systems
Discover the Power of Communications ‘
http://www.ameradio.com

References

• American Communication Systems | Two-Way Radio Dealer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>