kanto TTS150 Tabletop TV Stand User Guide
- June 9, 2024
- Kanto
Table of Contents
TABLETOP TV STAND
User Manual
Supporting your digital lifestyle™
TTS150 Tabletop TV Stand
Thank you for choosing Kanto
Read these instructions fully before assembly and installation. If you do not
understand these directions, or have any doubts about the safety of the
installation, please consult a qualified installation contractor. Make sure
there are no defective or missing parts.
Do not use defective parts. Kanto cannot be liable for property damage or
injury caused by incorrect mounting, incorrect assembly, lifting or incorrect
use of this product. If there is hardware missing, or if you are uncertain
whether a part is defective, please contact Kanto directly using one of the
methods below.
CAUTION
The maximum loading weight is 125 lb (57 kg). This mount is intended for use
only with the maximum weights indicated.
Use with products heavier than the maximum weights indicated may result in
instability causing possible injury. The surface you plan to affix the Kanto
mount to must be able to support more than 5 times the weight of the
television and the mount combined. Do not use this product for any purpose
other than to mount a VESA compliant TV as outlined in this manual.
Improper installation may cause damage to your TV or serious injury. This
product should not be mounted on steel stud or cinder block surfaces. Do not
install this product if you are unsure what kind of surface you may have or
the load it can support. You are advised to consult a qualified installation
contractor before installing this product.
Supplied Parts and Hardware
Required Tools
Project Overview
IMPORTANT!: Please read this entire document before attempting assembly.
If you have any problems or difficulties while following these instructions, please contact Kanto directly: Email: support@kantoliving.com / Toll Free: US & Canada: 1-888-848-2643
-
Select TV Screws and Spacers
1.1 A–G Select Screws
The back of your TV has 4 screw holes in a square or rectangular pattern. This is where the mount will attach to your TV.
Kanto provides several sizes and lengths of screws. This guide will help you select the right screws for your TV. You will only use 4 of the provided screws to attach your TV –the rest are not needed.
1.2 H–J Select Spacers
Plastic spacers are also provided in 3 thicknesses to allow the mount to work with curved TVs, and TVs that have recessed mount holes, protrusions, or inputs in the way. They can also be used to prevent the TV screws from going too deep and damaging your TV. You may not need spacers for your TV. -
Select Spacers for Irregular TVs
Spacers can be used to provide clearance around protrusions on the back of your TV, or to accommodate a curved TV. You may need to use longer screws. -
Attach TV Brackets
WARNING
Do not lay the TV face down on its front. Use a wall or TV stand.
Use whichever holes and slots work with your TV’s VESA pattern.
†Only applicable if using M5 / M6 screw -
Assemble Stand Base
-
Install Tilt Head
-
Attach TV Plate
-
Level Base
-
Hang TV
-
Level TV
-
Tilt TV
-
Manage Cables
-
Attach Safety Tether
CAUTION
Make sure the supporting surface will support the load limits outlined in the
caution on page two. Tighten Lag Bolt (N) until the Tether is snug flat
against the wall. Do not overtighten Lag Bolt (N). The Lag Bolt must be
located in the center of a wood stud.
| | www.kantomounts.com
---|---|---
|
1-888-848-2643
|
support@kantoliving.com
| kantoaudio.com
---|---
| Kanto Audio
| @kantoaudio
| Kanto Solutions
| kantoaudio
| Kanto Living
Limited Warranty to Original Purchaser
Kanto Living Inc. (Kanto) warrants the equipment it manufactures to be free
from defects in material for the limited warranty period of 5 years.
If equipment fails because of such defects and Kanto is notified within 5
years from the date of shipment with proof of original invoice from an
authorized reseller, Kanto will, at its option, provide replacement parts or
replace the equipment, provided that the equipment has not been subjected to
mechanical, electrical, or other abuse or modifications. Any replacement parts
or replacement units are warranted for 90 days from the day of reshipment to
the original purchaser.
Customers will be responsible for obtaining a Return Authorization Number and
paying shipping costs to return product to a Kanto location or authorized
depot. If the equipment is covered under the warranty provisions above, Kanto
will replace parts or provide a replacement unit, and be responsible for
shipping costs to the customer. Please keep the original packaging to prevent
damage to the product during shipping. Insuring your shipment is also
recommended.
The information in the manual has been carefully checked and is believed to be
accurate. However, Kanto assumes no responsibility for any inaccuracies that
may be contained in the manual. In no event will Kanto be liable for direct,
indirect, special, incidental, or consequential damages resulting from any
defect in the equipment, even if advised of the possibility of such damages.
This warranty is in lieu of all other warranties expressed or implied,
including without limitation, any implied warranty, including any warranty of
merchantability and fitness for any particular purpose, all of which are
expressly disclaimed.
www.kantomounts.com
support@kantoliving.com
Toll Free: 1-888-848-2643
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>