RAB H17 150W High Bay Fixtures Instruction Manual

June 9, 2024
RAB

INSTRUCTIONS
H17 & H17XL INSTALLATIONRAB H17 150W High Bay Fixtures
-

H17 150W High Bay Fixtures

RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com

IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
Suitable for wet locations. Maximum ambient temperature suitable for use in up to 50° C Suitable for wet locations. Maximum ambient temperature suitable for use in up to 50° C (122° F) (122° F)..

HOOK MOUNTING

  1. Screw the Eye-Bolt into the Fixture (Fig. 1). Tighten and secure with Set Screw (Fig. 2).
  2. Hang the Fixture on the Ceiling Hook or chain (provided by others) as shown in Fig. 2.
  3. After installation, connect the fi xture wires to power supply. Use appropriate UL approved wire connectors as required by code to complete wiring.

RAB H17 150W High Bay Fixtures - HOOK MOUNTING

SURFACE MOUNTING

(WITH ACCESSORY KIT)
(Accessory ordered separately – Model # H17-SM KIT)

  1. Secure bracket accessory kit (H17-SM Kit) to fi xture and mounting surface (Fig. 3) per H17-SM KIT instructions.
  2. After installation, connect the fi xture wires to power supply. Use appropriate UL approved wire connectors as required by code to complete wiring.
  3. Loosen Pivot Bolts and swivel fi xture to desired angle. Fixture can adjust 50° to the left or right vertically (Fig. 4).

RAB H17 150W High Bay Fixtures - SURFACE MOUNTING

PENDANT MOUNTING (WITH ACCESSORY KIT)

  1. Loosen Set Screw on the Fixture as shown in Fig. 5. Mount the H17-PM KIT into the driver housing using (1) 10×30 Screw (provided) for 120-277V installation. Use (1) 12×30 Screw (provided) for 480V installation. Use Bolt (provided) to secure the H17-PM Kit to driver housing.
  2. Insert 3/4” NPT Pendant Stem (not provided) into the H17-PM KIT and secure with Bolt (Fig. 6). Refer to H17-PM KIT installation instructions.
  3. After installation, connect the fixture wires to power supply. Use appropriate UL approved wire connectors as required by code to complete wiring.

RAB H17 150W High Bay Fixtures - PENDANT MOUNTING

WIRING

RISK OF FIRE. Universal voltage driver permits operation at 120V through 277V, 50 or 60 Hz. Units ordered with /480V suffi x are 480V only, 50 or 60Hz. For 0-10V dimming follow wiring directions as shown in Fig. 7. For non-dimming (on/off ), follow the wiring directions as shown in Fig.8.RAB H17 150W High
Bay Fixtures - RISK OF FIRE

FIELD-ADJUSTABLE CCT & WATTAGE

(120-277V ONLY)
Follow instructions below to change the Fixture Power (W) and/or Color Temperature (CCT ) from factory settings:
Factory Settings:
H17: 150W and 4000K
H17XL: 200W and 4000K

  1. Locate the Field Adjustable Switches on Fixture Housing as shown below. Remove waterprook gasket.
  2. Select Power (W) and/or Color Temperature (CCT) by sliding respective switch to the desired value (Fig. 9). Re-install waterproof gasket.

RAB H17 150W High Bay Fixtures - Color Temperature

MOTION SENSOR INSTALLATION

(PURCHASED SEPARATELY)

  1. Ensure power is off to the fixture to avoid risk of shock.
  2. Be sure to remove PIR40 Sensor pin protector before installing
  3. Remove the 1/2” Knockout with a screwdriver and install the Sensor Kit onto fi xture (Fig. 10) as per sensor kit instructions.

RAB H17 150W High Bay Fixtures - Sensor Kit

CLEANING & MAINTENANCE

CAUTION: Be sure  xture temperature is cool enough to touch.
Do not clean or maintain while xture is energized.

  1. Do not open fixture to clean the LED. Do not touch the LED.
  2. Do not touch refl ector, lens or trim cone.
  3. Do not clean any fixture surface with wood-base cleaning material such as paper towels or tissues.

TROUBLESHOOTING

  1. Check that the line voltage at the fi xture is correct. Refer to wiring directions.
  2. Is the fixture grounded properly?
    Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.

© 2023 RAB LIGHTING Inc.
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly – sales@rablighting.com
Free Lighting Layouts
Answered online or by request
H17_H17XL-IN 0323
P-100099
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals