EDIMAX GP-101IT Witches PoE Injector Installation Guide
- June 9, 2024
- EDIMAX
Table of Contents
GP-101IT
Quick Installation Guide
03-2021 / v1.3
GP-101IT Witches PoE Injector
Edimax Technology Co., Ltd.
No. 278, Xinhu 1st Rd., Nei hu Dist., Taipei City, Taiwan
Email: support@edimax.com.tw
Edimax Technology Europe B.V.
Fijenhof 2, 5652 AE Eindhoven, The Netherlands
Email: support@edimax.nl
Edimax Computer Company
530 Technology Drive Suite 100, Irvine, CA 92618, USA
Email: support@edimax.us
Product Information
I-1. Package Contents
I-2. Hardware Overview
I-3. LED Status
| Code | Name | Indication / Function |
|---|---|---|
| 1 | PORT LED | On: PD (Powered Device) connected Off: No PD connected |
| 2 | AC LED | On: Power on Off: Power off |
| A | DATA/POWER port | Data & power: Connect to a PoE PD (Powered Device such as |
PoE wireless access point)
B| DATA port| Data only: supports 10/100/1000 base Ethernet.
C| Power Socket| AC Power
I-4. Connections
Connect the injector as shown below:
The PoE/DATA port sends power and Ethernet data to your PoE-enabled device.
Use a CAT 5 cable to connect the PoE/Data port to your PoE-enabled device.
The DATA port doesn’t deliver power. Use an Ethernet cable to connect to the
injector’s Data port to the LAN of an Ethernet device, such as an Ethernet
switch.
Use the included power cord to connect the injector’s power socket to a power
source.
COPYRIGHT
Copyright © Edimax Technology Co., Ltd. all rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or
by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission from Edimax Technology Co.,
Ltd.
Edimax Technology Co., Ltd. makes no representations or warranties, either
expressed or implied, with respect to the contents hereof and specifically
disclaims any arranties,
merchantability, or fitness for any particular purpose. Any software described
in this manual is sold or licensed as is. Should the programs prove defective
following their purchase, the buyer (and not this company, its distributor, or
its dealer) assumes the entire cost of all necessary servicing, repair, and
any incidental or consequential damages resulting from any defect in the
software. Edimax Technology Co., Ltd. reserves the right to revise this
publication and to make changes from time to time in the contents hereof
without the obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly
different from those shown in this QIG. The software and specifications are
subject to change without notice. Please visit our website
www.edimax.com for updates. All brand and product
names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter. This device complies with Part 15 of
the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. Any changes or modifications not expressly approved by the party
responsible for compliance could void the authority to operate equipment.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 2.5cm (1 inch) during normal operation.
Federal Communications Commission (FCC) RF Exposure Requirements
SAR compliance has been established in the laptop computer(s) configurations
with PCMCIA slot on the side near the center, as tested in the application for
certification, and can be used in laptop computer(s) with substantially
similar physical dimensions, construction, and electrical and RF
characteristics. Use in other devices such as PDAs
or lap pads is not authorized. This transmitter is restricted for use with the
specific antenna tested in the application for certification. The antenna(s)
used for this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
R &TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF
THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment
and telecommunication terminal equipment and the mutual recognition of their
conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive
98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station
Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment.
All guidelines of this and of the computer manufacture must therefore be
allowed at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in
Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg,
Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Turkey, and United Kingdom. The ETSI version of this device is also
authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and
Switzerland.
EU Countries Not Intended for Use
None
EU Declaration of Conformity
This equipment is in compliance with the essential requirements and other
relevant provisions of Directive 2014/30/EU.
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as
household or general waste. It should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment, or
returned to the supplier for disposal.
Declaration of Conformity
We, Edimax Technology Co., Ltd., declare under our sole responsibility, that
the equipment described below complies with the requirements of the European
R&TTE directives.
Equipment: Gigabit PoE Injector
Model No.: GP-101IT
The following European standards for essential requirements have been
followed:
Directives 2014/30/EU
EMC: EN 55032:2015+AC:2016
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 55035:2017
Safety (LVD) : IEC 62368-1:2014 (2nd Edition) and/or EN 62368-1:2014+A11:2017
Edimax Technology Europe B.V.
Fijenhof 2,
5652 AE Eindhoven,
The Netherlands
Printed Name: David Huang
Title: Director
Edimax Technology Europe B.V.
a company of:
Edimax Technology Co., Ltd.
No. 278, Xinhu 1st Rd.,
Neihu Dist., Taipei City, Taiwan
Date of Signature: Nov., 2020
**** Printed Name:
Albert Chang
Title:
Director
Edimax Technology Co., Ltd.
References
- EDIMAX - Netwoking Solution Provider including SMB Wi-Fi Access Point, AP Controller, SMB and Industrial PoE++ L2+ Switch, Industrial Embedded Wirless (Wi-Fi, Bluetooth) USB Dongle (Adapter), Wi-Fi Smart Plug, IoT, Smart Home
- EDIMAX - Netwoking Solution Provider including SMB Wi-Fi Access Point, AP Controller, SMB and Industrial PoE++ L2+ Switch, Industrial Embedded Wirless (Wi-Fi, Bluetooth) USB Dongle (Adapter), Wi-Fi Smart Plug, IoT, Smart Home
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>