CNC4PC C92 Modbus Server User Manual
- June 9, 2024
- CNC4PC
Table of Contents
CNC4PC C92 Modbus Server
OVERVIEW
This card provides you with a serious Modbus or TCP / IP connection and has 3 configurable ports for TTL outputs and an analog port
FEATURES
- MODBUS TCP/IP and USB protocol.
- Pins 2-9 on IDC26 can be bi-directional, determined by the internal configuration. Presentation Screen LCD
- It can be powered with a voltage +5vc or IDC26 PIN or from the USB connector. Compatible with CNC controller board.
- 3 Expansion Ports. It has 3 x IDC26 connector for additional Breakout or Relay Boards.
- IDC 8pin male for analog input
- Visualization of the state of the pins on the display with TCP / IP
- IP configurable
- Display and encoder for configuration
- Din rail mountable
DESCRIPTION
TERMINAL POWER
Regulated 5VDC @0.5A is required to power this board
WARNING : Check the polarity and voltage of the external power source and
connect the 5VDC and GND. Overvoltage or reverse-polarity power applied to
these terminals can cause damage to the board, and/or the power source
MODBUS COMMUNICATION PROTOCOL
USB Communications
For Modbus RTU (Remote Terminal Unit) mode communications the default parameters are the following:
-
Baud Rate = 38,400bps
-
Data Bits = 8
-
Parity = None
-
Stop Bits = 1
-
Flow Control = None
Configuring the control software
To configure use the following sample configuration screen:
TCP/IP Communications
For Modbus TCP mode communications the default parameters are the following:
- IP address = Configurable in Board C92
- Port number = 502
Configuring the control software
To configure use the following sample configuration screen
Board Modbus addresses
Analog, Input and output pin discrete.
FUNCTION NAME | FUNCTION TYPE |
---|---|
DISCRETE OUTPUT | Write SingleCoils |
ANALOG INPUT | Read InputRegisters |
DISCRETE INPUT | Read Inputs |
PINOUT
PORT_1
IDC26 Pin number | ADDRESS MODBUS |
---|---|
1 | 100 OUT |
2 | 104 IN/OUT |
3 | 105 IN/OUT |
4 | 106 IN/OUT |
5 | 107 IN/OUT |
6 | 108 IN/OUT |
7 | 109 IN/OUT |
8 | 110 IN/OUT |
9 | 111 IN/OUT |
10 | 112 IN |
11 | 113 IN |
12 | 114 IN |
13 | 115 IN |
14 | 101 OUT |
15 | 116 IN |
16 | 102 OUT |
17 | 103 OUT |
18 – 25 | GND |
26 | +5VDC |
PORT_2
IDC26 Pin number | ADDRESS MODBUS |
---|---|
1 | 200 OUT |
2 | 204 IN/OUT |
3 | 205 IN/OUT |
4 | 206 IN/OUT |
5 | 207 IN/OUT |
6 | 208 IN/OUT |
7 | 209 IN/OUT |
8 | 210 IN/OUT |
9 | 211 IN/OUT |
10 | 212 IN |
11 | 213 IN |
12 | 214 IN |
13 | 215 IN |
14 | 201 OUT |
15 | 216 IN |
16 | 202 OUT |
17 | 203 OUT |
18 – 25 | GND |
26 | +5VDC |
PORT_3
IDC26 Pin number | ADDRESS MODBUS |
---|---|
1 | 300 OUT |
2 | 304 IN/OUT |
3 | 305 IN/OUT |
4 | 306 IN/OUT |
5 | 307 IN/OUT |
6 | 308 IN/OUT |
7 | 309 IN/OUT |
8 | 310 IN/OUT |
9 | 311 IN/OUT |
10 | 312 IN |
11 | 313 IN |
12 | 314 IN |
13 | 315 IN |
14 | 301 OUT |
15 | 316 IN |
16 | 302 OUT |
17 | 303 OUT |
18 – 25 | GND |
26 | +5VDC |
PORT ANALOG INPUT
IDC8 Pin number | ADDRESS MODBUS |
---|---|
1 | 400 |
2 | 401 |
3 | 402 |
4 | 403 |
5 | 404 |
6 | 405 |
7 | 406 |
8 | 407 |
CONFIGURE MENU
DIMENSION
All dimensions are in millimeters Fixing hole (3mm).
Disclaimer:
Use caution. CNC machines can be dangerous machines. Neither DUNCAN USA, LLC
nor Arturo Duncan are liable for any accidents resulting from the improper use
of these devices. This product is not a fail-safe device and it should not be
used in life support systems or in other devices where its failure or possible
erratic operation could cause property damage, bodily injury or loss of life.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>