Prescolite LBRA-6RD 6 inch 13W LED Downlight Module Instructions

: June 9, 2024
: prescolite

Table of Contents

INSTALLATION INSTRUCTIONS LBRA-6RD / 6RW
Support
Documents / Resources

Prescolite LBRA-6RD 6 inch 13W LED Downlight Module Instructions

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard. Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition

WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other reproductive harm. Thoroughly wash your hands after installing, handling, cleaning, or otherwise touching this product.

WARNING – Follow the Instructions carefully to assure full compliance with local, state, and NEC requirements. If there are any questions, contact a Qualified Electrical Contractor.

WARNING – Risk of fire or electrical shock. Consult a Qualified Electrician to ensure correct branch circuit conductor. Install this fixture only in Recessed Housings per the dimensions shown on model’s specification sheet. Do not make or alter any holes in an enclosure of wiring or electrical components during kit installation. Suitable for use with luminaire with a minimum of 75 C° supply conductors.

WARNING – To prevent wiring damage or abrasion, do not expose wiring to sheet metal edges or sharp objects. THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE APPLICABLE AND APPROPRIATE ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL REGULATIONS FOR ELECTRICAL INSTALLATIONS.

NOTE – This product is designed to operate with most standard low voltage electronic dimmer switches. Results may vary.For recommended dimmers, consult product spec sheet located on www.prescolite.com or call Technical Support at 1-888-PRS-4TEC.

NOTE – Always install within ambient temperatures specified on the product specification sheet. 5 year warranty. See www.prescolite.com for details.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
NOTE 2 : Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

INSTALLATION INSTRUCTIONS LBRA-6RD / 6RW

NOTE: This product fits into Prescolite and many competitive recessed cans. Refer to specific product specifications for your model. See www.prescolite.com for details.

IMPORTANT! For recessed housing installation, prior to retrofit installation, the housing must be properly installed and flush with the ceiling. It may be necessary to detach the socket from a mounting bracket inside the housing. Remove and discard the bracket to allow adequate clearance

Select the desired CCT using the switch on top of the trim (1).
Connect Trim to Power
For retrofit : Screw socket adapter (1) into socket (2) as shown or to hard-wire: cut medium base screw shell socket wires near the socket, discard socket. Cut and remove the screw shell adapter from trim, discard adapter. Strip wires and connect (Blk-Blk, Wht-Wht) with UL listed connectors.
For new construction with dedicated LED housing : Remove socket adapter assembly (1) and discard.
Connect trim connector (3) directly to mating housing connector (4) as shown.
Insert Trim into Recessed Housing: Guide socket and wiring toward the housing opening. Push trim up into recessed housing while twisting trim counterclockwise 1/4 turn, firmly engaging the spring clips (5) until flush with ceiling.
To remove the trim assembly in a housing, twist trim assembly counterclockwise 1/4 turn while pulling down.

Support

currentlighting.com/Prescolite

Prescolite logo

Documents / Resources

| Prescolite LBRA-6RD 6 inch 13W LED Downlight Module [pdf] Instructions
LBRA-6RD 6 inch 13W LED Downlight Module, LBRA-6RD, 6 inch 13W LED Downlight Module, Downlight Module
---|---