LIGHTPRO 211L LED Strip Connector User Manual

LIGHTPRO 211L LED Strip Connector User Manual

Thank you for buying the Lightpro LED Strip and Connector. This document contains the required information for correct, efficient, and safe use of the product. Consult the user manual of your transformer for more information about the set up and connection of your light plan or visit our website www.lightpro.nl.

Read the information in this manual carefully before using the product. Keep this manual near the product for consultation in the future.

PRODUCT DESCRIPTION

The Lightpro LED Strip is a lighting chain for outdoor use. The strip can be cut to the desired length before installation. Attention: before cutting, read the instructions in this manual carefully!

This product can be used as outdoor lighting incombination with the Lightpro 12 Volt system. Improper use of the product can have consequences for the safety, warranty, and correct functioning of the product and/or other parts of the system.

SPECIFICATIONS LED STRIP

• Article number: 175L
• Power (per meter) : 2,2W
• Luminous flux (per meter) : 80­100lm
• Protection class : IP67
• Ambient temperature : ­20°C to 50°C
• Dimmable : No
• Input: 12V (only with 211L Connector)

SPECIFICATIONS LED STRIP CONNECTOR

• Article number : 176L
• Maximum Power : 36W
• Afmetingen (l x b x h) : 1m x 28mm x 28mm
• Protection class: IP44 + IP67
• Ambient temperature : ­20°C to 50°C
• Cable length: 1m
• Input: 12V AC/DC
  

Packaging content

[Figure A]

1. LED Strip Connector
2. Sealing rubber
3. End cap
4. F­Connector (Article number 137A)

Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us.
E-mail: [email protected]

AVAILABLE SEPARATELY

[Figure B]

1. LED Strip (Article number 175L)

CUTTING

[Figure C]

The LED Strip can be cut to any desired length. Cut through in one movement from the transparent side

Carefully follow these instructions when cutting the strip

1. The LED Strip has been marked with the print DO NOT CUT HERE. Never cut in this part of the strip.
2. The strip can be shortened as desired. The part of the strip that is connected to the connector has to have at least one marking.
3. Short (remaining) parts of the LED Strip which do not have a marking will not light when connected to the connector.
4.  It is possible that a small part of a few centimetres at the end of the strip will not light up after cutting.

ASSEMBLE

[Figure D]
[Figure E]

1. Unscrew the screw cap and move it to the back.
   The LED Strip has to be connected in the right direction to the connector. When connecting, pay attention to the direction of the arrow with the print CONNECTOR. The arrow points in the direction of the connector

2. Place the sealing rubber at around 5 cm on the LED Strip.

3. Connect the LED Strip to the Connector. Make sure the pins in the connector make proper contact with the conductors in the strip.

4. Press the sealing rubber to the connector.

5. Place the screw cap on the connector and tighten properly.

6. Place the end cap at the end of the LED Strip..

INSTALLATION OF THE LIGHTS

• Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.
• If products are provided with a drain hole for water, this hole must be pointing downwards.
• Use non­corrosive fixing materials (supplied as standard) if you want to bolt the products down.
• Connect the lights to the main cable by using the connector as shown in figure on page 5.
• Consult the manual of your transformer for more information

SAFETY

• Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
• Turn off the system by pulling the plug of the transformer from the socket for maintenance.
• Regularly clean the product with a soft, clean cloth. Avoid abrasives that can damage the surface.
• Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
• Do not use a high pressure washer or aggressive chemical cleaning agents when cleaning the product. This can cause irreparable damage.
• Protection class III: this product may only be connected to safety extra­low voltage up to a maximum of 12 Volt.
• This product is suitable for outside temperatures of: ­20 to 50 °C.
• Do not use this product in areas where combustible gases, fumes or liquids may be stored

The product meets the requirements of the applicable EC, UK and EAEU guidelines.

For questions about parts, service, any complaints or other matters, you can contact us at any time. E­mail: [email protected]

Discarded electrical equipment must not be put in the household waste. If possible, take it to a recycling company. For details of recycling, contact a municipal waste processing company or your dealer.

5 year warranty – visit our website at lightpro.nl for warranty conditions.

References

• Lightpro
• Lightpro

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>