GOOVER PWR-G12V-030-66-U-D-J Universal Dimmable LED Driver User Guide

: June 14, 2024
: GOOVER

Table of Contents

FEATURES
TECHNICAL INFORMATION
FEATURES GENERAL WIRING DIAGRAM
TECHNICAL INFORMATION MUTI-CHANNELS WIRING DIAGRAM
MODEL/SKU
READ BEFORE INSTALLATION RISK OF SHOCK
CUSTOMERS SUPPORT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GOOVER PWR-G12V-030-66-U-D-J Universal Dimmable LED Driver

FEATURES

Constant voltage output
Auto reset breakers, from short circuit, overloading, & over temperature
Variable Input Voltage, 100-277VAC
Load 10-100%
Compatible with Triac, MLV,ELV,0-10V, & PWM Dimmers
Dry & Wet location
Flicker-free dimming
5 year Warranty
Cooling by free air convection
Full protection metal case

TECHNICAL INFORMATION

Model| Electrical|
---|---|---
| Voltage/Frequency| Input Inrush| Power Factor| Efficiency| AC Current(max)| Output Power| Output Current| Output Voltage| Length(A)| Width(B)| Height(C)| Net. Weight| Ambient Temperature
PWR G12V 030 66-U D-J| 100 277VAC@50/60Hz| 7A, 50%, 420us| 0.99@120VAC 0.98@277VAC| 0.79@120VAC 0.80@277VAC| 0.5A@100VAC| 30 Wmax| 2.5A| 12V DC| 6.50| 3.73| 1.58| 2.1 lbs| -22～140℉
PWR G12V 060 66-U D-J| 100 277VAC@50/60Hz| 14A, 50%, 780us| 0.98@120VAC 0.95@277VAC| 0.83@120VAC 0.85@277VAC| 0.9A@100VAC| 60 Wmax| 5A| 12V DC| 7.40| 3.73| 1.58| 2.4 lbs| -22～140℉
PWR G12V 100 66 U D-J| 100 277VAC@50/60Hz| 20A, 50%, 1.6ms| 0.98@120VAC 0.96@277VAC| 0.80@120VAC 0.83@277VAC| 1.4A@100VAC| 100 Wmax| 8.33A| 12V DC| 8.66| 3.73| 1.58| 2.8 lbs| -22～140℉
PWR G12V 150 66-U D-J| 100 277VAC@50/60Hz| 15A, 50%, 1.4ms| 0.98@120VAC 0.95@277VAC| 0.85@120VAC 0.86@277VAC| 1.8A@100VAC| 150 Wmax| 12.5A| 12V DC| 10.24| 4.13| 1.77| 4.2 lbs| -22～140℉
PWR G12V 180 66-U D-J-M| 100 277VAC@50/60Hz| 19A , 50%, 1.3ms @120VAC 38A, 50%, 960us @277AC| 0.99@120VAC 0.94@277VAC| 0.86@120VAC 0.88@277VAC| 2.2A@100VAC| 180W(360W)| 3×5A| 12V DC| 10.94| 4.33| 1.77| 5.1 lbs| -22～140℉
PWR G12V 300 66-U D-J| 100 277VAC@50/60Hz| 20A, 50%, 1.9ms| 0.99@120VAC 0.97@277VAC| 0.86@120VAC 0.88@277VAC| 3.4A@100VAC| 300Wmax| 12.5A| 12V DC| 10.95| 4.33| 1.77| 4.8 lbs| -22～140℉
PWR G12V 300 66-U D-J-M| 100 277VAC@50/60Hz| 35A , 50%, 960us @120VAC 43A, 50%, 1ms @277VAC| 0.99@120VAC 0.95@277VAC| 0.85@120VAC 0.9@277VAC| 3.6A@100VAC| 300W(560W)| 5×5A| 12V DC| 11.85| 4.33| 1.77| 5.5 lbs| -22～140℉

FEATURES GENERAL WIRING DIAGRAM

TRIAC dimming

0-10/1-l0V dimming

TECHNICAL INFORMATION MUTI-CHANNELS WIRING DIAGRAM

(MAXIMUM POWER PER CHANNEL IS 60W)

MULTI x3

MULTI x5

0-10/1-l0Vdimming

MODEL/SKU

READ BEFORE INSTALLATION RISK OF SHOCK

If direct wiring to a 120 volt circuit with an ac dimmer turn off power at circuit breaker before installing.
Always connect (+) to positive and (-) to negative. Make sure positive never touches negative while powered.
Allow ventilation, do not install in an airtight compartment. Cooler surrounding air temperatures extend driver life.
Operate only within temperature range of 4°F (-20°C) to 104°F(40°C).
Wiring must be in accordance with national & local electrical codes -low-voltage Class 2 circuit.
Mount the driver flat to the surface to provide heat transfer for better cooling.
It is normal for driver to feel warm to the touch, especially when under a full wattage load.
For wire runs inside walls, use certified CL2 or better cabling and appropriate mounting hardware.
Never connect 2 LED drivers to a single run of LED strips.
Total wattage of LED fixtures connected to driver must not exceed wattage rating of this unit.

If you don’t know the wattage rating of your lighting, ask the manufacturer of your lighting.

Power supply can be mounted vertically or horizontally. With a minimum of 2″ clearance around power supply to provide proper air circulation.
Before installing, check the label and ensure the power supply has the proper input voltage, output voltage, and wattage for the job. Check the wire markings to ensure they match the wiring diagram below. Refer to table above for the maximum loads!
Remove the two Phillips screws from the top of the driver housing and pull the cover off to expose the driver wires.
Insert the 120-277 VAC power into the driver housing from the electrical panel . Followed by bringing the 12V DC low voltage wires from the LEDs into the driver housing.
In addition bring the controller wire if applicable . Refer to diagram on page 2 to make all the proper wiring connections.
WIRING DIAGRAM
Insert the wire nut connections in the driver housing and close housing cover . Secure by tightening the two screws.