LIGHTPRO Eros Hi 12V Post Light User Manual

LIGHTPRO Eros Hi 12V Post Light

Thank you for purchasing the Lightpro Eros Hi/Lo. This document contains the required information for correct, efficient and safe use of the product. Consult the general manual of the Lightpro 12-volt system and the user manual of your transformer for more information about the set up and connection of your light plan.
Read the information in this manual carefully before using the product. Keep this manual near the product for consultation in the future.

PRODUCT DESCRIPTION

The Lightpro Eros Hi/Lo is a standing LED lamp for outdoor use. The fixture can be mounted on a solid surface or placed in the ground with the supplied spike. This product may only be used as outdoor lighting in combination with the Lightpro 12-volt system. Any alterations made to the product may have consequences for the safety, guarantee and correct functioning of the product and/or other parts of the system.

SPECIFICATIONS

• Product Eros Hi/Lo
• Article number 214P/217P
• Light source Filament LED
  • BA15D 4W AC/DC 12V
• Art. nr.: 6251011
• Power 4 W
• Luminous flux 280 lm
• Light colour 2.200 K
• Average lifetime 25.000
• Dimensions (H x Ø) 870 / 550 x 115 mm
• Protection class IP44
• Ambient temperature -20 °C to 50 °C
• Cable length 1 m
• Dimmable No
• Light source Replaceable Yes

PACKAGING CONTENT

1. Fixture Eros Hi/Lo
2. Ground spike
3. Screws for Ground spike
4. Screws
5. Plugs
6. Lightpro connector
7. Hex key
8. Foot
9. Light source
10. O-ring Ø25 x 3,5 mm

Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us. E-mail: info@lightpro.nl.

INSTALLATION

[Figure B]

Option 1: Placement in the ground
Attach the ground spike [2] to the base of the Eros using the 2 supplied screws [3]. For this, use the Allen key [7].

Option 2: Mounting onto a solid surface.

[Figure C]
Attach the foot [8] to the ground using the supplied screws [4].

• Pre-drill holes if necessary and use the supplied wall plugs [5].

REPLACING THE LIGHT SOURCE

[Figure D]

1. Remove the 3 screws using the supplied Hex key [7].
2. Carefully remove the glass from the pole.
3. Follow the instructions REPLACEABLE LIGHT SOURCE.
4. Place the glass and screws back into the correct position.

Attention: The glass is very fragile.

REPLACEABLE LIGHT SOURCE

To install or change the light source, proceed as follows:

1. Switch off the power source.
2. Let the light source cool down for at least 5 minutes.
3. Replace the light source, keeping in mind the following points:
   • Replace the light source with an identical one with the same specifications.
   • When (re)assembling, make sure that the parts are dry and clean.
   • Figure D3. Optionally, an O-ring can be placed around the light source. This serves to ensure that the light source is fitted straight into the luminaire.
4. Now you can switch on the power source again.

If the lamp does not light up after following the above instructions, do the following:

1. Switch off the power.
2. Check that all the plugs are connected properly.
3. Check the light source(s) and replace it if necessary.
4. Check the transformer and fuse (if applicable, and have it tested if necessary).
5. Check whether the cords are damaged.
6. Switch the power back on.

INSTALLATION OF THE LIGHTS

• Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.
• If products are provided with a drain hole for water, this hole must be pointing downwards.
• Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
• Connect the lights to the main cable by using the connector.
• Consult the manual of your transformer for more information.

SAFETY

• Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
• Turn off the system by pulling the plug of the transformer from the socket for maintenance.
• Regularly clean the product with a soft, clean cloth. Avoid abrasives that can damage the surface.
• Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
• Do not use a high-pressure washer or aggressive chemical cleaning agents when cleaning the product. This can cause irreparable damage.
• Protection class III: this product may only be connected to safety extra-low voltage up to a maximum of 12 Volt.
• This product is suitable for outside temperatures of:
  • 20 to 50 °C.
• Do not use this product in areas where combustible gases, fumes or liquids may be stored.

The product meets the requirements of the applicable EC, UK and EAEU guidelines.

For questions about parts, service, any complaints or other matters, you can contact us at any time. E-mail: info@lightpro.nl.

Discarded electrical equipment must not be put in household waste. If possible, take it to a recycling company. For details of recycling, contact a municipal waste processing company or your dealer.

Warranty

5-year warranty – visit our website at lightpro.nl for warranty conditions.

UK Authorised Representative (for authorities only) ProductIP (UK) Ltd. 8, Northumberland Av. London WC2N 5BY.

References

• Lightpro
• Lightpro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>