teesa TSA0528 Corded Hair Clipper Owner’s Manual
- June 9, 2024
- teesa
Table of Contents
teesa TSA0528 Corded Hair Clipper Owner’s
Thank you for purchasing TEESA appliance. Please read this operation instruction carefully before use, and keep it for future use. Producer does not take responsibility for damages caused by inappropriate handling and use of the product.
OVERVIEW
- Cutter
- Taper lever
- On/off switch
SAFETY INSTRUCTIONS
In order to reduce the risk of any injury, follow basic safety precautions applied when using any electrical device, including the following:
- Read this instruction manual carefully, even if you are familiar with the appliance.
- Before connecting the device to power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in the power supply socket.
- Do not use extension cord or a voltage converter with this appliance.
- Product intended for household use only. Not for commercial use.
- The appliance is intended for indoor use only.
- Do not use the product for purposes/uses different from what displayed in this operating manual.
- Clean and store this appliance in accordance to instructions listed in “Cleaning” and “Storage” section.
- ALWAYS turn off the device and disconnect it from the mains supply:
- if it’s not operating correctly,
- if there’s an uncommon voice when using,
- before disassembling the device,
- before cleaning,
- before servicing.
- When you disconnect the power cord, grasp and pull the plug, not the cord/cable.
- This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner, and all the safety precautions are understood and followed. Children should not play with this device. Children should not perform cleaning and servicing of the device unsupervised.
- Keep the appliance out of the reach of children.
- Fixed power cable may only be replaced in an authorized service point.
- Keep the device and its cord/cable away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord.
- Make sure the power cord does not touch any hot or sharp elements.
- Do not stretch, twist and curl the cable around the appliance.
- Use only original/authorized accessories.
- Before using the appliance, ensure that the blade is securely fitted.
- This product contains sharp blades, please take the utmost care in handling and use.
- Do not leave the appliance unattended when it is plugged in.
- DO NOT use this appliance if the cord or the plug is damaged, or the appliance is broken.
- Do not attempt to repair this appliance yourself. In case of damage, contact with an authorized service point for check-up/repair. Never disassemble this appliance.
IMPORTANT!
- DO NOT PLACE THE APPLIANCE IN WATER OR ANY LIQUID; NOR HANDLE/ USE IT WITH WET OR MOIST HANDS.
- DO NOT USE THE APPLIANCE NEAR WATER CONTAINED IN BATHTUBS, SINKS OR IN OTHER CONTAINERS.
- DO NOT PLACE OR STORE THE APPLIANCE WHERE IT CAN FALL OR BE PULLED INTO A TUB OR SINK.
- DO NOT REACH FOR THE APPLIANCE THAT HAS FALLEN INTO WATER. UNPLUG IT IMMEDIATELY.
TIPS BEFORE TRIMMING
- Prior to trimming, make sure hair is dry and clean.
- Comb the hair to get rid of any knots or tangles.
- Inspect the hair clipper and make sure there is no excessive oil on the cutting blades prior to use. Any excessive oil should be wiped off to prevent it from getting on your skin.
- Trim small amount of hair at a time.
- For the first use or when the user is not acquainted with the appliance, it is recommended not to trim to a short haircut. To achieve longer haircut, use a comb with higher markings (9, 12 mm).
- Hair length after trimming depends on the comb used. There are markings on each of the combs: 3 mm, 6 mm, 9 mm and 12 mm. Each marking corresponds to the hair length achieved after trimming.
OPERATION
-
Select the desired comb.
Note! Make sure that the appliance is turned off when attaching or removing the combs. -
Hold the comb with teeth up and slide it firmly onto the blade.
-
Connect the appliance to the power supply socket.
-
Push the on/off switch upwards to turn on the appliance.
-
Push the taper lever up or down to choose desired setting.
-
Start cutting your hair:
- To achieve best results it is recommended to stat trimming from the back and bottom of the head and moving the hair clipper upwards towards the top of the head.
- When cutting hair with a comb attached, make sure the cutter stays close to the skin.
- Use the appliance without comb attached for more precise trim (for example on the temples).
- The appliance has a sharp cutter. Therefore do not press the hair clipper too hard on the skin to avoid injuries.
- Use the included comb and scissors to further style your hair. Hold the hair with the comb and cut over the comb with the hair clipper or scissors.
-
After trimming, turn off the appliance by pushing the on/off switch downwards.
-
Disconnect the appliance from power supply socket.
-
If the appliance was used with the comb attached, remove and clean the comb and the whole appliance according to the instructions included in “Cleaning” section.
- When the lever is set to the highest position, the stationary and moving blades are close to each other, resulting in a short haircut. Set the lever to the lowest position to increase the distance between the two blades and as a result achieve longer haircut.
CLEANING AND MAINTENANCE
General:
- Do not immerse the appliance in water.
- Do not clean the cutter under running water. Clean it only with the included brush.
- Do not use any abrasives or chemical agents to clean this product.
- Clean only the casing with a soft and slightly damp cloth.
- Clean the appliance after each use. Regular cleaning guarantees better shaving performance.
- Make sure the appliance is turned off and disconnected from power mains.
- Use the included brush to clean the cutter.
- Clean the combs using the brush or rinse them under running water. Make sure to wipe them dry before refitting.
- The cutting blades should be lightly oiled with the oil provided every few haircuts.
STORAGE
- Before storing the appliance, make sure it is clean, dry and disconnected from the power supply.
- Make sure that while storing the power cord is not wrapped around the appliance.
- Use a hanging loop to store the device in a hanging position.
- Store the appliance in a dry, cool place, out of the reach of children.
SPECIFICATION
MAIN FEATURES
4 combs (3, 6, 9, 12 mm)
Stainless steel cutter
Hanging loop
TECHNICAL DATA
- Cutter width: 43 mm
- Length settings: 0,8 mm, 1,6 mm, 2,5 mm, 3,3 mm
- Noise level: ≤70 dB
- Power: 7 W
- Power supply: 230 – 240 V~; 50 Hz
- Weight: 395 g
- Dimensions: 169 x 61 x 32 mm
- Power cord length: 1,8 m
- In set: cutting head guard, 4 combs, cleaning brush, maintenance oil
Disposal
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or its literature,
indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400
Miętne.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>