FUSION MS-ERX400 Wired Remote Instruction Manual
- June 9, 2024
- FUSION
Table of Contents
FUSION MS-ERX400 Wired Remote
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the product box for
product warnings and other important information.
CAUTION
To avoid possible personal injury, always wear safety goggles, ear protection,
and a dust mask when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite side of the
surface to avoid damaging the vessel
What’s In the Box
- Mounting gasket
- Mounting template
- Four 8-gauge, self-tapping screws
- Two screw covers
- Dust cover
- Network/power cable
Tools Needed
- Phillips screwdriver
- Electric drill
- Drill bit (size varies based on surface material and screws used)
- Rotary cutting tool or jigsaw
- Silicone-based marine sealant (optional)
Mounting Considerations
- You must mount the remote control on a flat surface.
- If there is not much clearance behind the mounting surface or you prefer to drill a smaller hole in the mounting surface, you can use an MS-ERX400 spacer accessory (010-12922-02)
- If you are connecting the remote control to a stereo that may be exposed to water, add a drip loop to the cable near the stereo to allow water to drip off of the cable and avoid damage to the stereo. The drip loop should include the Ethernet cable and the power wires.
- If you need to mount the remote control on the exterior of a boat, you must mount it in a location far above the waterline, where it is not submerged, and where it cannot be damaged by docks, pilings, or other pieces of equipment.
Mounting the Remote Control
NOTICE
Do not use the remote control as a template when drilling the mounting holes
because this may damage the remote control and void the warranty.
Do not apply grease or lubricant to the screws when fastening the remote
control to the mounting surface. Grease or other lubricants can cause damage
to the remote control housing.
Before you can mount the remote control, you must select a location in
accordance with the mounting considerations.
-
Trim the template and adhere it to the mounting surface.
-
Drill a hole inside the corner of the dashed line on the template, and use a jigsaw or rotary cutting tool to cut along the inside of the solid line on the template.
NOTE : If you are using the accessory spacer and you would like a smaller hole in the surface, use a 44 mm (1 /4) hole saw to cut the hole shown on the template. -
Ensure the mounting holes on the remote control O line up with the pilot holes on the template.
-
Using an appropriately sized drill bit for the mounting surface and screw type, drill the pilot holes.
-
Remove the template from the mounting surface.
-
Complete an action:
-
If you are installing the remote control in a dry location, place the included mounting gasket on the back of the remote control.
-
If you are installing the remote control in a location that is exposed to water, apply silicone-based marine sealant on the mounting surface around the cutout.
NOTICE
Do not install the included mounting gasket if you applied sealant to the mounting surface. Using sealant and the mounting gasket may reduce water resistance. -
If you are using the spacer accessory, install the gasket or sealant on the back of the spacer.
-
If you will not have access to the back of the remote control after installation, connect the network/power
cable to the back of the remote control, and tighten the locking ring. -
If you are using the spacer accessory, install the spacer and gasket or sealant between the mounting surface and the remote control. Refer to the diagram that came with the spacer.
-
Secure the remote control to the mounting surface using the included screws 11 Snap the screw covers in place .
Power and Network Considerations
- If you must extend the power and ground wires, you must use the appropriate gauge of wires. 18 AWG (0.82 mm2) wires are suitable for most installations.
- If you must extend the network cable, extension cables and couplers are available. See your Garmin® dealer for details.
- This remote control can either connect to a single stereo, such as an MS-RA770, or it can connect to the Fusion PartyBus™ network to view and control all of the stereos on the network.
- You can use this example to help plan a basic Fusion PartyBus network. If you need information about creating a more advanced network with additional stereos and devices, see the installation instructions for your compatible stereo.
- MS-ERX400 remote control
- Wired network switch or wired network router
- Compatible stereo, such as an MS-RA770
- Compatible stereo, such as an MS-RA670
Connecting to Power and the Network
-
Route the network/power cable to the stereo or to the network switch or router.
NOTICE
Do not connect the cable to the stereo until after you have connected the power wires to avoid possible damage to the stereo.
TIP : To avoid running additional wires to the battery, you can connect the power and ground wires from this remote control to the power and ground wires used by the stereo. The stereo should be connected to power though the ignition or another manual switch. -
Connect the red power wire to the positive (+) battery terminal through the ignition or another manual switch .
WARNING
Do not remove the in-line fuse holder , to prevent the possibility of injury or product damage caused by fire or overheating. Connecting the wire without the appropriate fuse in place voids the product warranty. If you must extend the wire run, you should relocate the fuse so it is near the power source. -
Connect the black ground wire to the negative (-) battery terminal.
-
Select an option:
- If you are using this device to control one stereo and do not have additional devices on a Fusion PartyBus network, connect the network connector to the ETHERNET port on the stereo.
- If you have a network on the boat connecting multiple compatible devices, connect the network connector to an open port on the network switch or router.
More Information
Software Updates
- You must update the software for this device using a connected compatible stereo or using the Fusion-Link™ app.
- To make sure the device functions correctly with all compatible stereos on the Fusion PartyBus network, you should update the software in all FUSION devices after you install this device.
- For software update instructions, see the online owner’s manual for this device or for a connected compatible stereo.
Specifications
The device withstands incidental exposure to water of up to 1 m for up to 30 min, and is protected against powerful jets of water. For more information, go to www.garmin.com/waterrating.
Dimensions
- 12.3 mm (0.48 in.)
- 10 mm (0.39 in.)
- 10.9 mm (0.43 in.)
- 49.1 mm (1.93 in.)
- 70 mm (2.76 in.)
- 110 mm (4.32 in.)
© 2020 Garmin Ltd. or its subsidiaries
Garmin®, the Garmin logo, Fusion®, and the Fusion logo, are trademarks of
Garmin Ltd. or its subsidiaries, registered in the USA and other countries.
These trademarks may not be used without the express permission of Garmin.
M/N: A03775
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>