TROY LIGHTING B6513 Morgan Outdoor Wall Light Instruction Manual

June 9, 2024
TROY LIGHTING

TROY LIGHTING B6513 Morgan Outdoor Wall Light

WARNING
DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION

CAUTION

  • TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.
  • INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
  • If an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached.
    DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF OLDER WIRING.
    In regular circumstances the BLACK wire will be the “Hot” lead and the WHITE wire will be the “Neutral” or “Common” lead
    A GREEN or BARE COPPER wire is the “Ground”. In older buildings it is always good practice to reconfirm the polarity of the wiring

NOTICE

  • The important safeguards and instructions outlined on this sheet cannot cover all possible conditions and situations that may occur. it must be understood that common sense, caution and care factors that cannot be built into any product.
  • Caution and care must be supplied by the person(s) installing, operating and caring of this lighting fixture.
  • This fixture is designed to be mounted on a correctly installed standard round or octagon box or a through wiring box with a plaster frame. The box must be securely mounted to the structure of the building. The crossbar and hardware supplied should be used. directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.

NOTICE:
CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WNASH HANDS AFTER USE.

FIXTURE PREPARATION

  1. Remove the fixture, parts and parts bag(s) from the carton.

NOTICE
Before discarding the carton, double check to make certain that all parts are found.

FIXTURE INSTALLATION

  1. Attach the mounting plate to the outlet box. (The green screw should face against the wall). Adjust the threaded stud so they extend 3/16” beyond the backplate. (See Figure-01)

  2. Fasten the white fixture lead to the white wire in the outlet box. Fasten the wires together with an approved fastener (wire nut). Starting about 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener
    WARNING
    Make sure that there is no exposed wire or strands that could cause a dangerous short circuitTROY LIGHTING-B6513-Morgan-Outdoor-Wall-Light-fig-
\(2\)

  3. Connect the black fixture lead to the black wire in the outlet box. Fasten the joined wires as in step 3.

  4. Attach the backplate to the mounting plate and secure it with center lock up. (See Figure-02)TROY LIGHTING-B6513-Morgan-Outdoor-Wall-Light-fig- \(3\)

  5. Install the lamps. (type-B lamp)
    NOTICE:
    This fixture is rated for 60w type-B lamp.
    WARNING
    DO NOT EXCEED RECOMMENDED WATTAGE!

  6. Carefully insert the Center Glass Panel unto the SS frame. (See Figure-03)TROY LIGHTING-B6513-Morgan-Outdoor-Wall-Light-fig- \(4\)

  7. Carefully slide the Side Glass Panel unto the slots of SS frame. (See Figure-04)TROY LIGHTING-B6513-Morgan-Outdoor-Wall-Light-fig- \(5\)

  8. Attach the frame unto the backplate then secure it by the flat head screw. (See Figure-05)TROY LIGHTING-B6513-Morgan-Outdoor-Wall-Light-fig- \(6\)

  9. Restore power to the circuit breaker or fuse box

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

TROY LIGHTING User Manuals

Related Manuals