SUPERATV Can-Am Defender Convertible Cab Enclosure Doors Owner’s Manual
- June 9, 2024
- SUPERATV
Table of Contents
2753 Michigan Road · Madison, Indiana 47250 · 855-743-3427
INSTALLATION INSTRUCTIONS
Full Doors: for Can-Am Defender
Can-Am Defender Convertible Cab Enclosure Doors
- Make sure door handles are unlocked before installing.
- Do not discard packaging until product has been successfully installed.
- This item is not returnable if the protective film has been removed.
- Test fit to the cage to confirm fitment before removing film.
| Item | Description |
|---|---|
| A | Upper – D |
| B | Upper – P |
| C | Lower – D |
| D | Lower – P |
| Item | Description | M | Upper Hinge Bracket – D |
|---|---|---|---|
| E | Striker x 2 | N | Lower Hinge Bracket – P |
| F | Hinge Mount – P | P | Pillar Bracket – P |
| G | Hinge Mount – D | Q | Lower Hinge – P |
| H | Upper Hinge – P | R | Lower Hinge – D |
| J | Upper Hinge – D | S | Pillar Bracket – D |
| K | Clamp x 6 | T | Lower Hinge Bracket – D |
| L | Upper Hinge Bracket – P | U | Strut x 2 |
KEYS ARE LOCATED UNDER ORANGE TAPE. DO NOT DISCARD.
Door Cleaning:
- Do not use Rain-X®, Plexus ® or any other protector, wax, or polish.
- Do not use window cleaning fluids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
- Never use abrasive cleaners, abrasive pads, or gritty cloths.
- Never use razor blades, scrapers, squeegees, brushes, etc.
- Thoroughly rinse Doors to float off dirt and mud.
- Using a soft cloth, or microfiber cloth, clean Doors with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand washing soap can also be used.
- To prevent water spots, use a chamois to blot Doors dry.
Removal: keep all components removed from machine.
• Install provided “U” Nut to Pillar.
• Repeat for opposite side.
Do not tighten any hardware unless noted.
- Install Pillar Bracket – P (P) with hardware shown. Tighten hardware.
- Install Clamp (K) to Pillar Bracket – P (P) and Frame. Tighten hardware.
- Install Striker (E) to Pillar Bracket – P (P) with hardware shown.
• Install Upper Hinge – P (H), Lower Hinge – P (Q), and Strap to Hinge Mount – P (F) with hardware shown.
-
Secure Hinge Mount – P (F) and Clamps – P (K) to machine with hardware shown.
-
Install Foam as shown.
-
Repeat steps for opposite side.
-
Install Upper Hinge Mount – D (M) and Lower Hinge Mount – D (T) to Upper and Lower Doors with hardware shown.
-
Repeat steps for opposite side.
-
Place Lower Hinge Bracket – D (T), on Lower – D (C) onto Lower Hinge – D (R).
-
Place Upper Hinge Bracket – D (M), on Upper – D (A) onto Upper Hinge – D (J).
-
Join Upper and Lower Doors with hardware shown; tighten hardware.
-
Secure Strap to Lower – D (C).
-
Close Door, engage Latch / Striker Pin, and align Door to machine.
-
Tighten all hardware.
-
Open Door and install Strut (U) to Upper and Hinge Mount.
-
Secure with hardware shown; tighten hardware.
-
Remove installed Mounts on Mirrors. Use 8mm wrench. Discard Mount and hardware.
-
Install Mirror to Door with hardware shown. Tighten hardware.
Need help with your installation?
| sales@superatv.com| |
www.superatv.com
---|---|---|---
| 1-855-743-3427| | 8:00am – 8:00pm EST
M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
(kit contents continue on following page)
Read instructions and view illustrations before beginning.
Thank You For Choosing
© 2022 SuperATV.com®
All Rights Reserved.
IN-DOOR-CA-DEF-003 4/21/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>