EDIMAX EN-9320SFP+ V2 10 Gigabit Ethernet SFP+ PCIe Network User Manual

: June 9, 2024
: EDIMAX

Table of Contents

Product Information
Hardware Installation
Driver Installation
More Information
Safety Instructions
FCC Caution
EU Declaration of Conformity
WEEE Directive & Product Disposal
Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EDIMAX EN-9320SFP+ V2 10 Gigabit Ethernet SFP+ PCIe Network User Manual

Product Information

The EN-9320SFP+ V2 equipped with Marvel AQC100 controller delivers 10Gbps (Max.) data transmission and effectively prevents packet loss.

Package Contents

EN-9320SFP+ V2
**QIG

**

**Low Profile Bracket

**

LED Status

Function	LED Status	Definition
SPEED (Link)	On (Amber)	Link at 10Gbps/ 1Gbps
Off	Port disconnected or link fail
Activity	On (Green)	Link at 10Gbps/ 1Gbps
Blinking (Green)	Data transmitting
Off	Port disconnected or link fail

System Requirements

Supported Operating System: Windows7/8/8.1/10/11 or Linux
Empty PCIe 2.0 Slot (x4 or Higher)

*Additional version information may be announced on the EDIMAX website.

Hardware Installation

Turn off your computer, unplug the power, and remove the computer casepanel.
Refer to your computer’s user manual if you are unsure how to remove the case panel and find the location of an availiable PCIe slot.
Insert the EN-9320SFP+ V2 Network Adapter into an available PCIe slot.
An additioanal Low Profile bracket is also included in the package contents.
Secure the EN-9320SFP+ V2 in place by screwing the metal bay screw, and turn on the computer

Driver Installation

Please follow the instructions below to install the driver.

Download the Driver

Please access the link below. Search the model no. “EN-9320SFP+ V2” in the search box. Find the proper driver for your Operation System, click to download and save it your computer Desktop.

https://www.edimax.com/download

More Information

Unzip the Driver

After you downloaded the proper driver for your Operating System, please unzip it from your computer Desktop for driver installation.

Install the Driver

Click on “Marvell_ Fast Lin Q _Edge”, and follow the steps of setup wizard to complete the driver installation.

Install the Driver

Confirmation of Driver Installation

To confirm the EN-9320SFP+ V2 is working properly with following steps.

A. Right-click the Windows Start button, and select the “Device Manager”.
B. Double-click the “Network Adapter” to expend the list of Nework Adapter.
C. Right-click on the Network adapter and select “Properties”.

EN-9320SFP+ v2 is working properly!!

More Information

For more information, please visit our website with the following URL or scan the QR code:
https://www.edimax.com/download

Please search the model no. “EN-9320SFP+ V2” to enter the referred page.
More Information

Safety Instructions

he following general safety guidelines are provided to help ensure your own personal safety and protect your product from potential damage. Remember to consult the product user instructions for more details.

This product is designed for indoor use only.
Static electricity can be harmful to electronic components. Discharge static electricity from your body (i.e. touching grounded bare metal) before touching the product.
The device contains no user serviceable parts. Do not attempt to service the product and never disassemble the product.
Do not spill food or liquid on your product and never push any objects into the openings of your product.
Do not use this product near water, areas with high humidity, or condensation.
Keep the product away from radiators and other heat sources.
This device is not designed to be operated by children.
Always unplug the product from mains power before cleaning and usea dry lint free cloth only.

COPYRIGHT

Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system,or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd.

Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability, or fitness for any particular purpose. Any software described in this manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)assumes the entire cost of all necessary servicing, repair, and any incidental orconse quential damages resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation to notify any person of such revision or changes.

The product you have purchased and the setup screen may appear slightly different from those shown in this QIG. The software and specifications are subject to change without notice. Please visit our website www.edimax.com for updates. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

FCC Caution

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accep tany interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turningthe equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland.

EU Countries Not Intended for Use

None

EU Declaration of Conformity

This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU

WEEE Directive & Product Disposal

At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal.

Declaration of Conformity

We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives.

Equipment: 10 Giga SFP+ port PCIE NIC
Model No.: EN-9320SFP+ V2

The following European standards for essential requirements have been followed:

Directives 2014/30/EU

EMC : EN 55032:2015/A11:2020
- EN 55035:2017/A11:2020
- AS/NZS CISPR 32:2015

Edimax Technology Europe B.V.

Fijenhof 2,
5652 AE Eindhoven,
The Netherlands
Date & Place of Issue: 31/May/2022, Eindhoven
Signature:

Printed Name: David Huang
Title: Director

a company of: Edimax Technology Co., Ltd. No. 278, Xinhu 1st Rd., Neihu Dist., Taipei City, Taiwan

Date & Place of Issue: 31/May/2022, Taipei
Signature:
Printed Name: Hunter Chen
Title: Director

We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the Unite Kingdom EMC and Safety directives.