VONROC EH501AC Electric PTC Fan Heater Instruction Manual

VONROC EH501AC Electric PTC Fan Heater

Original Instructions
This product is only suitable for well-insulated spaces or occasional use.

SAFETY INSTRUCTIONS

Read the enclosed safety warnings, the additional safety warnings, and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire, and/or serious injury. Save the safety warnings and the instructions for future reference.

The following symbols are used in the user manual or on the product:

• Read the user manual.
• Denotes risk of personal injury, loss of life or damage to the tool in case of non-obser-vance of the instructions in this manual.
• Denotes risk of electrical shock.
• Important! WARNING: In order to avoid overheating, do not cover the heater.
• Earthing symbol. This appliance is classified as protection class I and must be connected to an earthed mains socket.
• Do not dispose of the product in unsuitable containers.
• The product is in accordance with the applicable safety standards in the European directives.

GENERAL SAFETY WARNINGS
This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision. Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

CAUTION
Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

ADDITIONAL SAFETY WARNINGS FOR ELECTRIC HEATER

• Children should be kept away unless continu-ously supervised to ensure that they do not play with the heater.
• Children shall not plug in, position, operate, regulate, or clean the appliance or perform user maintenance.
• CAUTION-some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
• The heater is not suitable for use outdoors in damp weather, in bathrooms or in other wet or damp environments.
• Please note that the heater can become very hot and should, therefore, be placed at a safe distance from flammable objects such as furniture, curtains, and similar.
• Use a handle when moving this heater.
• Do not move the heater when it is heated. Allow the product to thoroughly cool before handling it.
• Do not cover the heater.
• The heater must not be located immediately below a socket outlet.
• Do not connect the heater using an on/off timer or other equipment which can automatically switch the device on.
• The heater must not be placed/used in rooms where flammable liquids or gases are used or stored.
• If an extension cord is used, it must be as short as possible and always be fully extended.
• You must not connect other appliances to the same main socket as the heater.
• Do not use the heater in the immediate surroundings of a bath, a shower, or a swimming pool.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
• Make sure the heater is always under surveillance and keep children and animals away from it.
• Do not place/use the heater on moving vehicles or somewhere easy to be tripped over.
• When the heater is not used for a long time, unplug the heater from its means. Pull the plug straight out, never remove the plug by pulling the cord.
• Keep the heater far from the curtain or places where the air inlet can easily be blocked.
• The power coupler is waterproof when not in use. In order to prevent possible electric shock or leakage current, never use the heater with wet hand or operate the heater when there is water on the power cord.
• Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.
• Warning! Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided.
• Warning! To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1 m from the air outlet.

Electrical safety
When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions.

Always check that the voltage of the power supply corresponds to the voltage on the rating plate label.

Connecting to the power supply
Check that the power supply and plug are used in accordance with your machine. Have a look at the rating plate on the machine. Any changes should always be carried out by a qualified electrician.

• Warning! This machine must be earthed. If not properly earthed this machine can cause an electrical shock. Be sure that the power supply outlet is earthed. If there is any doubt, have it checked by a qualified electrician?
• Warning! Avoid contact with the terminals on the plug when installing (removing) the plug to (from) the power supply outlet. Contact will cause a severe electrical shock.

Replacing cables or plugs
If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent in order to avoid a safety hazard. Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.

Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum conductor size is 1.5 mm². When using a cable reel always unwind the reel completely.

PRODUCT INFORMATION

Intended use
Electric PTC fan heater for warehouses, workshops, and household use only. Do not use the product for any other purpose. The heater can be used in enclosed rooms in a free-standing position for room heating. The heater may only be used completely mounted and standing vertically on a stable surface. It incorporates a thermostat and a self-resetting thermal cut-out to control the heating element and therefore the temperature.

TEHNICAL SPECIFICATIONS

**Model No.**

|

EH501AC/EH501AC_GREY/EH501AC_WHITE

|

EH502AC

---|---|---
Power supply| 220-240V ~ / 50Hz
Power rating| 2000W| 3000W
Protection class| Class I
IP degree| IP20
Settings| 25W (only fan)

1000W / 2000W

| 25W (only fan)

1500W / 3000W

Self-resetting

Thermostat

| 68°C| 85°C
Heating capacity| 20m²| 30m²
Weight| 1,7 kg| 2,85 kg

DESCRIPTION

The numbers in the text refer to the diagrams.

1. Handle
2. Heating element
3. Air inlet
4. Air outlet
5. Power indicator
6. Function knob
7. Off
8. Fan
9. Low heating mode
10. High heating mode
11. Thermostat knob
12. Tilt adjustment knob
13. Power cable

OPERATING

Check the device for damage before use and only use in good working condition.

When using the heater for the first time, you may notice a slight emission of smoke. This is quite normal and it stops after a short time. The heating element is made of stainless steel and was coated with protection oil by production. The smoke is caused by the left oil when heated.

Placing the electric heater (Fig. A)

• Place the heater upright on a firm and a level surface.
• Keep a minimum distance of 1 m between the front of the housing and walls, combustible materials (furniture, curtains, etc.) and 30 cm from all other housing surface areas. Keep away from wet environments.
• After long storage always make sure the heating element (2) is clean and free from dust.

Warning!
Make sure to place the heater in a safe spot, so you cannot easily trip over the machine and cable. Make sure to place the heater where it cannot fall down/of.

Starting the electric heater (Fig. A, B)

• Turn the adjustment knobs (12) counterclockwise to loosen.

• • Tilt the heater to the desired position.
  • Turn the adjustment knobs (12) clockwise to tighten them securely.

• • Plug in the cable (13) to the mains.
  • Set the thermostat knob (11) to the Max.
  • The heater will switch on when the function knob
  (6) is set to one of the function settings.
  • The power indicator light (5) will turn on.
  • Once the room reaches the required temperature, turn the thermostat knob (11) back slowly until you hear back until you hear a click and the power indicator light (5) turns off.
  • The heater now starts and stops automatically and therefore keeps the room temperature constant. This means once the temperature decreased, the heating element and fan will start again.

Function settings (Fig. B)
Different functions are possible by turning the function knob (6).

• Power off (7)
• Fan only (8)
• Low heating mode (9)
• High heating mode (10)

Tip-over switch
This heater has digital tip-over protection. This protection ensures when the heater is not placed upright on a firm and level surface or when the heater tip over, the system will automatically shut the heater off. If this occurs, put the heater on a firm and level surface and start the heater again.

Automatic Overheat Safety Control
This heater is equipped with a safe internal heat-limiting thermostat and overheats protection circuit. When a potential overheating temperature is reached, the system will automatically shut the heater off.

Stopping the electric heater (Fig. A, B)
Let the machine cool down before turning it off by using the ventilation function.

• Turn the thermostat knob (11) to the lowest position and turn the function knob to the fan position (8).
• Let the fan cool down the appliance for a few minutes.
• Turn the function knob (6) to the off position (7).
• Pull the plug out of the mains.

Storing the electric heater

• Always let the heater cool down completely before storing the machine.
• Never wrap the cable around the heater.
• Warning! Never store the machine in a wet or dusty environment.

MAINTENANCE

Before cleaning and maintenance, always switch off the machine and remove the mains plug from the mains.

Cleaning
Let the machine cool down completely before cleaning.

• Clean the heater with a dry towel or vacuum cleaner.
• In order to protect the enclosure, don’t splash water onto the heater, and never use a solvent like gasoline, isoamyl acetate, toluene, etc. to clean the heater.
• When you store the heater, let it cool down first and, keep it dry.

Troubleshooting

In case the electric heater does not work well, we give you subjoined some possible causes and their solutions.

The heater does not operate, even when it is plugged in and the switch and thermostat are switched on.| The plug is a loose, bad connection| Pull out the plug, and check the connection of the plug and socket. Then connect again.
No power in the socket outlet| Insert the plug in a proper socket
Tip-over protection| Put the heater on a firm and level surface.
Overheat protection| Unplug the heater and wait at least 30 minutes to cool down before restarting the heater.
The heating element glowing| The input voltage is too high or too low| Use the power supply according to the rating on the label
The air inlet (3) grill is blocked| Keep the heater far away from articles like curtains, plastic bags, paper, and other things which can cover the inlet or can be easily covered on the air inlet
The appliance didn’t heat up, only the ventilator worked| The switch was not put at the heating setting| Turn the switch to the heat setting
The thermostat operated| Turn the thermostat and listen if there is an open/closed voice. If there is no click and the thermostat is not damaged, the heater will automatically switch on when the appliance cooled down
The self-retting cut-out operated| Turn the heater off and inspect the blockage of the inlet or outlet. Disconnect the plug and wait at least 10 minutes for the protection system to reset before attempting to restart the heater.
Abnormal noise| The appliance is not standing upright| Put the heater on a level surface

ENVIRONMENT

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

WARRANTY

VONROC products are developed to the highest quality standards and are guaranteed free of defects in both materials and workmanship for the period lawfully stipulated starting from the date of original purchase. Should the product develop any failure during this period due to defective material and/or workmanship then contact VONROC directly.

The following circumstances are excluded from this guarantee:

• Repairs and or alterations have been made or attempted to the machine by unauthorized service centers;
• Normal wear and tear;
• The tool has been abused, misused or improperly maintained;
• Non-original spare parts have been used.

This constitutes the sole warranty made by the company either expressed or implied. There are no other warranties expressed or implied which extend beyond the face hereof, herein, including the implied warranties of merchantability and fitness for a particular purpose. In no event shall VONROC be liable for any incidental or consequential damages. The dealer’s remedies shall be limited to the repair or replacement of nonconforming units or parts.

The product and the user manual are subject to change. Specifications can be changed without further notice.

Model Identifier

Model identifier(s): EH501AC / EH501AC_GREY / EH501AC_WHITE

Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage local space heaters only (select one)
Nominal heat output| Pnom| 2.0| kW| manual heat charge control, with integrated thermostat| No
Minimum heat output (indicative)| Pmin| 1.0| kW| manual heat charge control with room and/or outdoor temperature feedback| No
Maximum continuous heat output| Pmax,c| 2.0| kW| electronic heat charge control with room and/or outdoor temperature feedback| No
Auxiliary electricity consumption| | fan assisted heat output| No
At nominal heat output| elmax| 0| kW| Type of heat output/room temperature control (select one)
At minimum heat output| elmin| 0| kW| single stage heat output and no room temperature control| No
In standby mode| elSB| 0| kW| Two or more manual stages, no room temperature control| No
| | | | with mechanic thermostat room temperature control| Yes
| | | | with electronic room temperature control| No
| | | | electronic room temperature control plus day timer| No
| | | | electronic room temperature control plus week timer| No
| | | | Other control options (multiple selections possible)
| | | | room temperature control, with presence detection| No
| | | | room temperature control, with open window detection| No
| | | | with distance control option| No
| | | | with adaptive start control| No
| | | | with working time limitation| No
| | | | with black bulb sensor| No
Contact details| VONROC • Lingenstraat 6 • 8028 PM • Zwolle • The Netherlands
Model identifier(s): EH502AC

Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage local space heaters only (select one)
Nominal heat output| Pnom| 3.0| kW| manual heat charge control, with integrated thermostat| No
Minimum heat output (indicative)| Pmin| 1.5| kW| manual heat charge control with room and/or outdoor temperature feedback| No
Maximum continuous heat output| Pmax,c| 3.0| kW| electronic heat charge control with room and/or outdoor temperature feedback| No
Auxiliary electricity consumption| | fan-assisted heat output| No
At nominal heat output| elmax| 0| kW| Type of heat output/room temperature control (select one)
At minimum heat output| elmin| 0| kW| single-stage heat output and no room temperature control| No
In standby mode| elSB| 0| kW| Two or more manual stages, no room temperature control| No
| | | | with mechanic thermostat room temperature control| Yes
| | | | with electronic room temperature control| No
| | | | electronic room temperature control plus day timer| No
| | | | electronic room temperature control plus week timer| No
| | | | Other control options (multiple selections possible)
| | | | room temperature control, with presence detection| No
| | | | room temperature control, with open window detection| No
| | | | with a distance control option| No
| | | | with adaptive start control| No
| | | | with working time limitation| No
| | | | with a black bulb sensor| No
Contact details| VONROC • Lingenstraat 6 • 8028 PM • Zwolle • The Netherlands

DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European Parliament and of the Council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:

EN 60335-1, EN 60335-2-30, EN 62233, 2014/35/EU, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, 2014/30/EU, 2011/65/EU, 2012/19/EU.

VONROC • Lingenstraat 6 • 8028 PM Zwolle • The Netherlands.

©2022 VONROC
WWW.VONROC.COM
2208-24.

References

• VONROC Gereedschap & Tuin artikelen

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>