PureLink PT-HDBT-1020C-TX HDBaseT 3.0 USB-C Video and Data Transmitter User Manual
- June 9, 2024
- PureLink
Table of Contents
PT-HDBT-1020C-TX HDBaseT 3.0 USB-C Video and Data Transmitter
User Manual
PT-HDBT-1020C-TX
PT-HDBT-1020C-TX HDBaseT 3.0 USB-C Video and Data Transmitter
HDBaseT 3.0 USB-C Video and data Transmitter
Model PT-HDBT-1020C-TX
Designed in Germany
© 2022 PureLink GmbH All rights reserved.
Preface
Read this user manual carefully before using this product. Pictures shown in
this manual are for reference only. Different model layouts and specifications
are subject to the physical product.
This manual is for operation instructions only, not for any maintenance usage.
In the constant effort to improve our product, we reserve the right to make
changes in functions or parameters without prior notice or obligation.
Trademarks
Product model and logo are trademarks. Any other trademarks mentioned in this
manual are acknowledged as the properties of the trademark owner. No part of
this publication may be copied or reproduced without the prior written
consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. It has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a commercial installation.
Operation of this equipment in a residential area is likely to cause
interference, in which case the user at their own expense will be required to
take whatever measures may be necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would
void the user’s authority to operate the equipment.
REACH | 1907/2006/EU
ROHS | 2011/65/EU
PureLink hereby declares that this product PureTools PT-HDBT-1020C-TX complies
with Directives 1907/2006/EU und 2011/65/EU.
EMC / LVD (Electro Magnetic Compatibility / Low Voltage Directive)
PureLink GmbH hereby declares that this product PureTools PT-HDBT-1020C-TX
complies with Directives 2014/30/EU and 2014/35/EU. The full text of the EU
Declaration of Conformity is available at the following Internet address:
http://www.purelink.de/ce/4251364735787_CE.pdf
SAFETY PRECAUTIONS
To ensure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference.
- Unpack the equipment carefully and save the original box and packing material for possible future shipment
- Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
- Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
- Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
- Refer all servicing to qualified service personnel.
- To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
- Do not put any heavy items on the extension cable in case of extrusion.
- Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards.
- Install the device in a place with fine ventilation to avoid damage caused by overheat.
- Keep the module away from liquids.
- Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
- Do not twist or pull by force ends of the optical cable. It can cause malfunction.
- Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
- Unplug the power cord when left unused for a long period of time.
- Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.
Product Introduction
1.1 Introduction
The PT-HDBT-1020C-TX is an uncompressed 18G HDBaseT3.0 transmitter that allows
1 USB-C input signal to be transmitted over distances up to 100m at 4K@60Hz/
1080p@60Hz via CAT6A cable. The transmitter features one USB-C input and one
HDBT output. For the USB-C input, it provides an AV ideal interface for
connecting to the modern PC.
1.2 Feature
- USB-C input supports 4K@60Hz 4:4:4.
- Supports to transmit uncompressed 4K/1080p signal up to 100m.
- Supports bi-directional 24V PoC power supply.
- Micro-USB for firmware upgrade.
1.3 Package List
- 1x Transmitter
- 1 x Power Adapter(24V, 1.25A)
- 2 x mounting ears &2x screws
- 1 x Manual
Note: Please contact your distributor immediately if any damage or defect in the components is found.
Panel Description
| No. | Name | Description |
|---|---|---|
| 1 | USB-C IN | Connects to the Macbook or other device with SlimPort output. |
| 2 | FW | Micro-USB for firmware upgrade |
| 3 | HDBT OUT | RJ45 port to connect the HDBT input port of receiver by CAT6A |
| 4 | DC24V | DC connector for the power adapter connection. |
| 5 | Power Led | The LED illuminates green when the power is connected |
Specification
| Video | Transmitter |
|---|---|
| Input | (1)USB-C IN |
| Input Connector | (1) Type-C |
| Input Resolution | Up to 4K@60Hz 4:4:4 |
| Output | (1) HDBT OUT |
| Output Connector | (1) RJ45 |
| Output Resolution | Up to 4K@60Hz 4:4:4 |
General
HDCP Version| Input: HDCP 2.2, HDCP 1.4 compliant
PoC| Supported bi-directional 24V PoC
USB Data| USB data Max 272Mbps
Transmission Distance| 4K/1080p ≤ 328 feet (100 meters)
Operation| -5 to +55℃(+23° to +131°F)
Storage Temperature| -25 to +70℃(-13° to +158°F)
Relative Humidity| 10% to 90%, Non-condensing
Power Supply| Input:100V~240V AC; Output:24V DC 1.25A
Power Consumption| 14 W
Dimension (WHD)| 90 x 21.7 x 120 mm
Net Weight| 260g
System Diagram
The following diagram illustrates typical input and output connections that can be utilized with the KVM extener.
After-Sales Service
If there appear some problems when running the product, please check and deal with the problems referring to this user manual. Any transport costs are borne by the users during the warranty.
1) Product Limited Warranty: This product will be free from defects in
materials and workmanship for three years (The purchase invoice shall
prevail).
Proof of purchase in the form of a bill of sale or receipted invoice which is
evidence that the unit is within the Warranty period must be presented to
obtain warranty service.
2) What the warranty does not cover (servicing available for a fee):
- Warranty expiration.
- Factory applied serial number has been altered or removed from the product.
- Damage, deterioration or malfunction caused by:
- Normal wear and tear.
- Use of supplies or parts not meeting our specifications.
- No certificate or invoice as the proof of warranty.
- The product model showed on the warranty card does not match with the model of the product for repairing or had been altered.
- Damage caused by force majeure.
- Servicing not authorized by distributor.
- Any other causes which does not relate to a product defect.
- Delivery, installation or labor charges for installation or setup of the product.
3) Technical Support: For any questions or problems, contact your distributor or reseller and tell them the respective product name and version, the detailed failure situation as well as the formation of the cases.
Asking for Assistance
Technical Support:
Phone: +49 5971 800299 – 0
Fax: +49 5971 800299 – 99
Technical Support Hours:
8:30 AM to 5:00 PM Monday thru Thursday
8:30 AM to 4:00 PM Friday
Write to:
PureLink GmbH
Von-Liebig-Straße 10
D – 48432 Rheine
www.purelink.de
[email protected]