PureLink FX-I500 USB 3.1 AOC Cable Instruction Manual
- June 4, 2024
- PureLink
Table of Contents
- ****
- PureLink FX-I500 USB 3.1 AOC Cable
- INTRODUCTION
- INTENDED USE
- SAFETY INSTRUCTIONS
- FEATURES
- APPLICATION
- SPECIFICATIONS
- CROSS SECTION
- OPERATION AND CONNECTION DIAGRAM
- MAINTENANCE
- CLEANING
- WARRANTY AND LIABILITY
- DISPOSAL OF THE DEVICE
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
****
PureLink FX-I500 USB 3.1 AOC Cable
INTRODUCTION
Thank you for purchasing the Fiber Optic USB 3.1 Gen 2 Type C-C AOC Cable. This Cable allows you to transmit USB signals to a distance of up to 30m without an external power supply. This cable is a hybrid cable containing both fiber optic and copper cores.. It supports a maximum data rate of 10 Gbps per channel, is lightweight, flexible, and has an ultra-small fixed installation bending radius of 20mm.
INTENDED USE
This product is intended for indoor use only. Do not use it outdoors. Contact
with moisture, e.g. in bathrooms, must be avoided under all circumstances. For
safety and approval purposes (CE), you must not rebuild and/ or modify this
product. If you use the product for purposes other than those described above,
the product may be damaged. In addition, improper use can cause hazards such
as short-circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to
third parties only together with its operating instructions.
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/ guarantee.
The device is not a toy. Keep it out of the reach of children and pets. Do not
leave packaging material lying around carelessly. These may become dangerous
playing material for children. Risk of suffocation!
The maximum pulling tensile load of the cable is 157N (16kg). Never pull the
cable with higher load. The minimum bending radius of the hybrid cable is
approximately 20mm, bending the cable to a smaller radius will irreversibly
destroy the cable.
Pay attention to trip hazards; make sure that the cable is installed safely.
Protect the product from extreme temperatures, direct sunlight, strong jolts,
high humidity, moisture, flammable gases, vapors and solvents.
Do not place the product under any mechanical stress. If it is no longer
possible to operate the product safely, take it out of operation and protect
it from any accidental use.
Safe operation can no longer be guaranteed if the product:
- is visibly damaged
- is no longer working properly
- has been stored for an extended period in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
Please handle the product carefully. Jolts, impacts or a fall even from a low
height can damage the product.
Also observe the safety and operating instructions of any other devices which
are connected to the product.
Consult an expert when in doubt about the operation, safety or connection of
the device.
DELIVERY CONTENT
- 1x AOC Cable
- 1x User Manual DE/EN
- 1x Warning Insert
FEATURES
This AOC Cable has many features that enable it to perform in a superior manner. Among those features you will find:
- Meet USB 3.1 Gen2 Standard , bandwidth can reach to 10Gbps super speed
- Support length up to 30m .(Custom length is available)
- Hybrid optical cable with fiber and copper wire
- Support two sides plug and play
- No RF interference , working stable in complex environments
APPLICATION
This product is for example applicable to:
- Computers / PCs
- Wearables
- TVs / Displays
- Projectors
- Mobile phones
- Power Banks
- Cameras
- Home Cinema
- Medical applications
- LED video walls
- TV Stations
- Digital Signage and more can be used
SPECIFICATIONS
Mechanical properties and Environmental performance:
Tensile strength (Long-term) | N | bis zu 157N |
---|---|---|
Crush resistance (Long-term) | N/100mm | 1000N |
Minimum bending radius (dynamic) | mm | 20 D* |
Minimum bending radius (static) | mm | 10 D* |
*D = the diameter of the cable body, in this case it is 4.5mm
Spezifications
Units | Transmitter (Source) | Receiver (Display) |
---|---|---|
USB Version | USB 3.1 Gen 2 Standard | |
Video Bandwidth | 10Gbps. | |
O/E Converter | 2 channel 850 nm VCSEL array | 2 CH GaAs PD array |
Connector Type | USB Type-C | |
Cable Type | Hybrid type with OM3 fiber and copper wire | |
Cable Outer Diameter | 4.5 mm | |
Jacket Outer Material | PVC | |
Differential Input | 100 Ohm | |
Power Consumption | 0.5W | |
Power Supply | Non external power required | |
Passive Power Supply | 5V |
Environmental Conditions:
- Operating Temperature: -10–50°C
- Storage Temperature: -20–60°C
- Relative Humidity: 10–80%RH
CROSS SECTION
Construction:
Hybrid cable, fiber (high speed data) & copper (low speed signals)
Cable construction:
2 fiber cores and 2 cooper conductors
- Cable jacket: PVC
- Diameter: 4.5mm
- Connector dimensions: 39159.5mm
- Connector material: zinc alloy
OPERATION AND CONNECTION DIAGRAM
Attention:
The FX-I530 is designed for use with the + 5V passive power supply, provided
by the host device through the USB connection. This +5V connection, as well as
powering the internal fiber optic module, is also carried through to the other
sink via a full standard copper connection. Please make sure, that the host
device is capable of delivering more than 500mA.
Before using this cable, please make sure that all devices which will be
connected with the AOC USB Cable are shut down and without power.
Then you can start to connect the “host side” of the USB plug to the
transmitter and connect the “remote (device) side” of the other USB plug to
the receiver/display. This works without additional power supply.
We do not recommend using any intermediate cables or adapters between the
connections, as the signal transmission performance maybe attenuated. Switch
on the power of the device of the type C host and the remote.
MAINTENANCE
There are no components located inside the product you need to maintain. Never open/dismantle the product. Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop. If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.
CLEANING
Before cleaning the product it must be disconnected from all other connected products. Do not use abrasive or solvents or any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause damage to the housing and malfunctioning. To clean the product, a dry, soft and clean cloth is sufficient. Do not apply too much pressure to the housing as this may cause scratch marks. You can easily remove dust using a long-haired, soft and clean brush.
WARRANTY AND LIABILITY
The producer grants 2 years warranty to a new device. As the manufacturer has
no influence on installation, warranty only applies to the product itself.
If any fault or damage is detected on your product, please contact your dealer
and provide your sales slip or invoice as evidence of the purchase, if
necessary. Your dealer will repair the fault either on site, or send the
device to the manufacturer. You make the work of our technicians considerably
easier, describing possible faults in detail – only then you can be assured
that faults, occurring only rarely, will be found and repaired with certainty!
The manufacturer is not liable for damages to persons or property caused by
improper installation, operation or maintenance, not described in this manual.
Do not alter or modify the product or its accessories. Any use other than
described in this user`s manual is not permitted and causes loss of warranty,
loss of guarantee, and non-liability.
CE CONFORMITY
PureLink GmbH hereby declares that the FX-I500 Series complies with
Directive 2014/30/EU.
DISPOSAL OF THE DEVICE
WEEE-Reg. Nr.: DE 93847290 According to the European WEEE directive, any electrical and electronic equipment must not be disposed with consumers waste. As a consumer, you are committed by law to reposit electrical and electronic devices to public collecting points or to the dealer for free at the end of the device’s lifetime. Details are regulated in the respective national legislations. The garbage can symbol on the product, in the manual or on the packaging refers to these terms. With the return of your used devices you actively take part in protecting the environment.
DISCLAIMER
This product complies with the statutory national and European requirements.
All company names and product names are trademarks of their respective owners.
All rights reserved. We reserve our right for misprints and changes of the
device, packing or user`s manual.
PureLink GmbH Von-Liebig-Straße 10 48432 Rheine
Deutschland
Tel.: +49 (0) 5971 800 299-0
Fax: +49 (0) 5971 800 299-99
info@purelink.de
www.purelink.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>