PureLink USB32-E100 USB 3.2 100 Meter Extender Over CAT User Manual

May 15, 2024
PureLink

PureLink USB32-E100 USB 3.2 100 Meter Extender Over CAT

Specifications

  • Technical Standard: USB3.2 Gen1

  • Max Transmission Distance: 100m over CAT6a/7

  • Data Rate: Up to 5Gbps bidirectional

  • Ports & Interfaces:

    • Transmitter: 1x USB Type-C, 1x RJ45, 1x 3-Pin Terminal Block
    • Receiver: 3 x USB Type-A, 1x USB Type-C, 1x RJ45, 1x 3-Pin
      Terminal Block, 1x 3.5mm Phone Jack
  • Power: USB 5V (Transmitter), 12V 1.5A (Receiver)

  • Ambient Temperature: Operate: 0°C ~ 40°C,
    Storage: -20°C ~ 60°C

  • Operating Altitude: Up to 3000m

  • Humidity: 20% ~ 90% RH

  • Physical Characteristics:

    • Transmitter: 50 x 93 x 32mm, 128g
    • Receiver: 87 x 123 x 32mm, 259g

Product Usage Instructions

Installation:

To install the PureLink USB32-E100:

  1. Connect the TX and RX with CAT6a cable or better.
  2. Apply power to the TX.
  3. Add your USB devices to the system.

Operation:

Transmitter Controls and Functions:

  • HDBaseT: To connect to the receiver.
  • RS-232: To connect to RS-232-command-controllable device (Needs terminal block to RS-232).
  • USB Type-C: To connect to USB3.2 Gen1 source.
  • Power/Link LED: Refer to LED Indicator.

Receiver Controls and Functions:

  • DC Jack: To plug in DC 12V power adapter.
  • Console: To update firmware (needs 3.5mm jack cable to UART).
  • RS-232: To connect to RS232-command-controllable device (needs Terminal Block to RS-232).
  • HDBaseT: To connect to the transmitter.
  • USB TypeC/Type-A: To connect to USB device, USB3.2 Gen1 / 2.0 / 1.1 / 1.0.
  • Power/Link LED: Refer to LED Indicator.

LED Indicators Interface:

No. Name LED Color Status
1 Power (Green) On Power On
2 Link (Blue) Off RJ45 Unlinked

Frequently Asked Questions

  • Q: What is the maximum transmission distance of the PureLink USB32-E100?
    • A: The PureLink USB32-E100 provides up to 100 meters of reliable extension over CAT6a/7 cable.
  • Q: What type of USB devices can be connected using the USB32-E100?
    • A: The USB32-E100 is compatible with USB cameras, touch panels, desktops, laptops, and more.

Introduction

PureLink’s USB32-E100 USB-C 3.2 Gen 1 provides up to 100 meters of reliable extension. Adding the USB32-E100 could not be simpler, connect the TX and RX with CAT6a cable or beter, apply power to the TX, add your USB devices, and that’s it! The USB32-E100 is a perfect extension solution for USB cameras, touch panels, as well as desktops, laptops, and more. TAA Compliant.

Features

  • USB-C to USB-C, or USB-C to USB-A
  • 100 Meter over CAT6
  • USB 3.2 Gen 1 (5 Gbit/s)
  • Extends:
    • USB2.0 and USB 1.1
    • RS-232
  • TAA Compliant
  • Plug and Play
  • Optional Rack Mount (USB32-E100-RACK)

Specifications

Technical Transmiter Receiver
Standard USB3.2 Gen1 USB2.0 USB1.1

USB1.0

| USB3.2 Gen1 USB2.0 USB1.1

USB1.0

Max Transmission

Distance

| 100m over CAT6a/7
Data Rate| USB3.2 Gen1 up to 5Gbps bidirectional
Ports & Interfaces
USB Data| 1x USB Type-C| 3 x USB Type-A

1x USB Type-C

Transmission Medium| 1x RJ45| 1x RJ45
RS232| 1x 3-Pin Terminal Block| 1x 3-Pin Terminal Block
Console| | 1x 3.5mm Phone Jack
Power
Power Supply| USB 5V| 12V 1.5A
Power Consumpution| 2W| 2.76W (Does not include USB DEVICE)
Power Saving| 1.6W| 1.8W
Ambient Temperature
Operation| 0 to 55°C
Storage| -40 to 80°C
Operating Altitude| 2000m
Humidity| Up to 95%
Physical Characteristics
Dimension| 50 x 93 x 32mm| 87 x 123 x 32mm
Weight| 128g| 259g

Operation Controls and Functions

TransmiterPureLink-USB32-E100-USB 3-2-100-Meter-Extender-Over-CAT-FIG
\(1\)

No. Name Function Description
1 HDBaseT To connect to the receiver
2 RS-232 To connect to RS-232-command-controllable device (**Needs terminal

block to RS-232)
3| USB Type-C| To connect to USB3.2 Gen1 source
4| Power/Link LED| Refer to LED Indicator


No. Name Function Description
1 DC Jack To plug in DC 12V power adapter
2 Console To update FW (needs 3.5mm jack cable to UART)
3 RS-232 To connect to the RS232-command-controllable device

(needs Terminal Block to RS-232)

4| HDBaseT| To connect to the transmitter
5| USB Type- C/Type-A| To connect to USB device, USB3.2 Gen1 / 2.0 / 1.1 / 1.0
6| Power/Link LED| Refer to the LED Indicator

LED Indicators

Interface LED Color Status
Power (Green) On Power On
Off Power Off
Link (Blue) On RJ45 Linked
Off RJ45 Unlinked

RS-232 Pin Define

Installation

Step 1 Use machine screws to fix angle brackets on both sides of your product .PureLink-USB32-E100-USB 3-2-100-Meter-Extender-Over-CAT-FIG
\(4\)

Step 2 Use self-drilling screws to fix the product on a platform.

Step 3 Move the product to get fixed and then lock the screws.

Wall Installation

Step 1 Same way as “Installed on a Platform”, but need to put screw plugs into the pilot hole before inserting the screws (leave 2mm space from the platform )PureLink-USB32-E100-USB 3-2-100-Meter-Extender-Over-CAT-FIG
\(7\)

DIN-Rail Installation

Step 1 Use machine screws to fix a DIN-rail mounting plat on the side of your product.

Step 2 Install your product on a DIN-rail as following instructionPureLink-
USB32-E100-USB 3-2-100-Meter-Extender-Over-CAT-FIG \(9\)

Rack Installation

Step 1 Lock machine screws in the rack.PureLink-USB32-E100-USB 3-2-100
-Meter-Extender-Over-CAT-FIG \(10\)
Step 2 Put your products on the rack.PureLink-USB32-E100-USB 3-2-100-Meter-
Extender-Over-CAT-FIG \(11\)
Step 3 Push the products to the other side of the rackPureLink-
USB32-E100-USB 3-2-100-Meter-Extender-Over-CAT-FIG
\(12\)

Step 4 Install the rack in a cabinetPureLink-USB32-E100-USB 3-2-100-Meter-
Extender-Over-CAT-FIG \(13\)

Warranty

Three (3) Year Limited Warranty for PureStream™ Branded Products Only
Dtrovision, LLC. (hereinafter “PureLink”) warrants its HDTools and PureStream™ branded products (hereinafter “Product”) purchased directly from PureLink or Dealer shall be free from defects in workmanship and materials, under normal use and service, for a period of three (3) years on parts and three (3) years on labour. Any repaired or replaced equipment related to the Product shall be covered only under the remaining portion of the warranty. This warranty has no relationship to and exists independently of any warranty offered by Dealer. This warranty is a limited warranty and gives you specific legal rights. You may also have other rights which vary from state to state.

TERMS & CONDITIONS

PureLink shall repair or replace the Product if it develops a material fault during the period of warranty, on condition that i) the Product has only been subject to normal use in a domestic or commercial environment in a manner consistent with its specification and functionality, ii) the Product has been cared for reasonably and only subjected to reasonable wear and tear, iii) the defect has not been caused by willful or negligent abuse or neglect, or any accident or improper installation procedure, iv) the serial number of the Product has not been altered or removed.
This warranty only applies to the original purchaser and shall be the exclusive remedy to the original purchaser. PureLink shall not be liable for any damages whatsoever caused by Product or the failure of Product to perform, including incidental or consequential damages. PureLink shall not be liable for any claim made by a third party or made by the purchaser for a third party.
Except as expressly set forth in this warranty, PureLink makes no other warranties, expressed or implied, including any implied warranties of merchantability and fitness for a particular purpose. PureLink expressly disclaims all warranties not satisfied in this limited warranty. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.

WARRANTY RETURNS/REPAIRS/EXCHANGES

No merchandise may be returned without prior authorization from PureLink, and a Return Materials Authorization (RMA) number. Failure to comply with these conditions will result in the rejection of the returned merchandise.
Any warranty service on Products must be arranged through Dealer. Authorized returns must be shipped freight prepaid and fully insured to PureLink, Ramsey, NJ USA, with the RMA number clearly marked on the outside of all shipping boxes and containers. PureLink reserves the right at its sole discretion to refuse any shipments arriving freight collected or without an RMA number. Any authorized returned merchandise must be accompanied by a note describing the reason for return, along with contact information including name, phone number, return mailing and shipping addresses, e-mail address, and RMA number.
On any products returned and accepted with an RMA number, return freight charges following repair of items under warranty shall be paid by PureLink, shipping by the standard ground carrier of its choice.

ADVANCE WARRANTY REPLACEMENTS

PureLink’s advance replacement service offers a Replacement Unit upon request – free of charge for eligible products purchased less than one (1) year of the warranty claim. Products purchased more than one (1) year prior to the warranty claim do not qualify for advance replacement services. Advance replacement requests must be validated by a member of PureLink’s Technical Support Team. Replacement units may be new or refurbished and is subject to availability. PureLink is responsible for shipping the Replacement Unit to your designated location by standard ground service. All other shipping methods will be the responsibility of the Dealer Original Unit Return – the Original Unit must be returned within thirty (30) calendar days of the return authorization date. Failure to return the Original Unit within this period will be subject to a minimum 15% re-stocking fee. Dealer is solely responsible for the shipping of the Original Unit to PureLink.

TO MAKE A WARRANTY CLAIM

To make a warranty claim, promptly notify PureLink within the warranty periods described above by calling PureLink’s Technical Support Department at 1-201-488-3232. PureLink, in its sole discretion, will determine what action, if any, is required under this warranty. Most problems can be corrected over the phone through close cooperation between Customer and a PureLink technician. To better enable PureLink to address a warranty claim, please have the Product’s serial and model numbers. If PureLink, in its sole discretion, determines that an on-site visit or other remedial action is necessary, PureLink may send a representative to Customer’s site.

CUSTOMER SERVICE

Technical support inquiries can be submitted electronically through the PureLink website at www.purelinkav.com. For immediate assistance please contact PureLink’s Customer Care Team at

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals