BURTON BA 64V Sound Bar User Guide
- June 9, 2024
- Burton
Table of Contents
BA 64V Sound Bar
User Guide
BA64V BURTON
Experience true audio excellence
BURTONAUDIO.COM
Precautions
- Before using this machine for the first time, please read the user manual carefully and follow all operating instructions and precautions.
- Because the high voltage inside the machine is dangerous, do not repair it by yourself. All repairs and adjustments must be performed by professionals.
- The power source used in this machine must match the type indicated on the nameplate.
- The power supply on the socket must not be overloaded, the power cord should be placed where it cannot be stepped on, and items should not be placed on the power cord.
- Do not place this machine on a sofa, near unventilated places such as curtains, or in direct sunlight and humidity, and avoid dropping or subjecting this machine to shock.
- Unplug the machine from the power outlet before cleaning. Do not use thinner or other chemical cleaners, Just wipe with a soft cloth
- After the machine is turned off, ifyou do not use the machine for a long time or in a thunderstorm, please unplug the power plug from the power
- To avoid the risk of fire, electric shock, or product damage, do not expose the machine to rain, moisture, or dripping liquids, and do not place water-containing objects such as vases on the machine.
- Do not expose batteries or battery-installed devices to excessive heat, such as sunlight and fire.
Panel and interface functions
-
Audio display screen
-
Audio auxiliary input
-
Audio USB Interface
-
Audio Optical input
-
Audio coaxial input
-
Audio HDMI(ARC) input
-
Subwoofer Output
-
DC powerjack (This interface is limited to passive subwoders with an impedance of 8 ohms)
-
Audio control buttons
Power and input selection button: Long press to switch between standby and boot, short press to switch input mode when booting
Volume down and previous song buttons: Press and hold to decrease the volume of the audio in the power-on state; short press in Bluetooth playback mode and USB playback mode to switch to the previous song.
Volume up and next song buttons: Press and hold to increase the volume of the audio In the power-on state; short press in Bluetooth playback mode and USB playback mode to cut to the next song -
Audlopower switch
Audio power cord
Sound bar and device connection diagram
Audio cable and TV connection diagram
Coaxial connection
diagram with TV or network set-top box
Optical connection
diagram with TV or network set-top box
Remote control function introduction
Power button: press to boot
USB play mods button: press to switch to LW piaybeck.
Blueboth playback mode button: prase to switch to Bluetooth playback.
Speaker volume up button press to Increase speaker volume.
Speaker volum e down button: Press to decrease speaker volume.
Next button: You can ‘winch to the next song In USB playback modeand
Blueboth playback mode
Play pause
button: Moss to swilch play and pause.
** Previous bulb rc USB playback mode and Blueboth playback mode can be
switched to the previous song.
EQ:** Press to swibli between different sound modes
1. Music: Press to switch the speaker’s playback profile to music mode; this
mode provides balanced audio playback. Itstenln
2. Movie: Press to switch the playback mode of the speaker to the movie mode;
in this made, the speaker will produce a simulated surround effect. enhanOng
the presence of the movie.
3. News This mode highlights the medium frequency and prov Ides clearvolce.
Treb+: Preasto increase the treb input volume
Treb-: Press to decrease the treb Input volume
Bess + :Press to increase the bass input volume
Bass-: Riess to decrease the bass output volume
Source selection button Press to switch between AUX coaxial fiber’ input modes
Functional operation
1.POWER
After connecting the audio signal cable to the corresponding interface of the
machine, plug in the power cable and turn the power switch to ON; the LED
display will show the current working mode.
2. Working mode conversion
After powering on, short press the “ ‘button on the rear panel of the machine
or the remote control audio source button to switch to different working
modes; the LED display shows the working mode corresponding to the
characters:BT = Bluetooth OPT = Optical input COX = Coaxial input LINE =
auxiliary input USB = USB playback ARC=HDMI(ARC) input
3. Volume button operation function
The remote control’s ‘Volume + and ‘Volume -‘ long or short press can increase
or decreese the volume, the LED display will show the corresponding volume
level, the maximum level is 32.
4. Bluetooth operation method
This product will automatically enter the pairing mode when using the
Bluetooth input mode for the first time. At this time, the LED display will
show BL end flicker. You car directly use your Bluetooth playback device to
connect to this product. When the connection is successful, a voice prompt
“Bluetooth has connection”. This product will automatically switch to pairing
mode when no device is connected in Bluetooth mode. If you Intend to switch to
another Bluetooth playback device while the Bluetooth playback device is
connected, please disconnect the Bluetooth playback device that is currently
connected, wait for the product to automatically switch to Bluetooth pairing
mode, end then use the new Bluetooth playback device. Connect.
Wall operation
- Choose a hole location on the wall; make sure the hole location you choose is horizontal before drilling.
- Use a 6mm drill bitand a power drill (not supplied) to drill the marked locations.
- Insert the included plastic sleeve into the hole and push until the plastic sleeve Is flush with the wall
- Screw the provided bracket into the drilled hole and fasten it to the wall.
Note: The distance between the holes on the leftand right sides of
thewall is 376mm, and thedlstance between the left and right acrewa la 24mm.
Insert the henging
piece on the back of the pull tube into the metal hook on the bracket to hang
it.
Technical Parameter
| Product Model | Ba Sev |
|---|---|
| Product Name | Sound Bar |
| Pawn suPPW | AC 100-240V ∼ 50/60H2 0.5A |
| output power | 40w+40w |
| Internee | USB 1 oPticel “put Interface 1 3.Smm recording Interface *1 |
Conic input Interface I RCA Ono Input !Merl/ace 1 HOIARARC)input Interface
1
Sound mods| Film + Music + News
Weed| 3K6
Themachine size| 1065113.3*66.36aw
Accessorise| Manual. remote control, warranty card
This product Is only suitable for safe use In areas below 2000 meters above
sea level
Disconnecting device description
Since the power plug is used as the main power source to cut off the mach ine,
conned the machine to en easily accessible AC outlet. If you notice any
unusual condi:lona, immediately unplug the power plug from the AC powerplug.
BURTONAUDIO.COM
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.