elipson HORUS 6B Speaker User Manual

elipson HORUS 6B Speaker

Dear Customer

Thank you for choosing an Elipson audio product. Please read carefully the following information before using your new loudspeakers. It contains tips to get the most of it and instructions for safety use. We strongly recommend that you keep the packaging and this user manual for further use.

CONTENT

• 1 speaker: HORUS 11F, HORUS 8S, HORUS 10C
• 2 speakers: HORUS 6B
• 1 user manual
• 1 removable grid (all speakers)
• 1 removable base + 4 screws: HORUS 11F
• 4 rubber pads per speaker: HORUS 6B, HORUS 8S, HORUS 10C
• 4 decoupling (thread M6) spikes per speaker: HORUS 11F

PREPARATION

1. Mounting the removable base on the cabinet (HORUS 11F)
   • Carefully turn the cabinet over and place it on the packaging foams, or on a carpet, to avoid any damage on the top part. Take care not to damage the cabinet, and the drive units during this operation. Adjust the base on the cabinet and screw it using the four provided screws.
2. Sticking the rubber pads
   • We recommend that you stick the rubber pads, provided with the removable base, on the loudspeakers. If you use the loudspeakers without the removable base, you should place the rubber pads on the provided inserts, to avoid any damage. As a rule, you can stick the rubber pads under the loudspeakers or under its base in order to protect the loudspeaker itself and its base.
3. Putting spikes (HORUS 11F)
   • After mounting the base of the speaker, screw the spikes on it (no required tools).
   • Note: The presence of pads or decoupling spikes prevents vibrations to be transmitted to the floor.

STEREO SETUP

Position of the speakers FL/FR

The Horus loudspeakers have been designed to reproduce all types of music as accurately as possible, provided that a few rules should be followed to optimize performance and achieve a realistic sound image. Ideally, the speakers should be placed symmetrically in front of the listening position to form an equilateral triangle. The cabinets should be placed at the same height and the same distance from the rear wall and the adjacent side surfaces.

In order to optimize the setup of the speakers in your listening room, we recommend the following tests:

• Above all, you should avoid positioning the loudspeakers in the corners of your room. The result will be an artificial increase in the level of bass, masking the speed and details of this range.
• First, adjust the spacing of the two speakers in order to find the realistic balance between a wide sound image (wide apart speakers) and a sound image respecting the punctuality of the voices (close speakers).
• Secondly, move the speakers away from the rear wall by steps of 10 cm to find the balance between the depth of the sound image (far from the back wall) and the level of the extreme low frequencies (close to the back wall).
• Finally, adjust the loudspeakers orientation by turning them gradually toward the center of the listening area. If you leave the speakers parallel, you may want to bring them closer together, if you orient them more than 30°, you may increase their spacing.

Connections

WARNING: ALL THE CONNECTIONS MUST BE MADE WITH THE EQUIPMENT TURNED OFF.

It is essential to connect the speakers using the correct polarity. Make sure to connect the “ + ” terminal of the speaker (Red) to the “ + ” output terminal of the amplifier. Then, make sure to connect the “ – ” terminal of the speaker (Black) to the “ – ” output terminal of the amplifier. A wrong connection would cause a cribled stereo image and loss of bass. Use high quality speaker cable.

• FR/FL

| FRONT RIGHT/LEFT| Speaker Front right (R) /Left (L)

HOME-CINEMA SETUP 5.1

Position of the speakers FL/FR

Before continuing the operation, please configure your installation by following the instructions on the previous pages

Position of the center speaker C (HORUS 10C)

The center speaker must be positioned near the screen for realistic reproduction of dialogue. Ideally, it is placed under the TV set if the TV stand enables it. If a standard projection screen is used, the center speaker should be placed at the bottom of the screen for best results. If a microperforated screen is used, it can be positioned behind the screen.

Position of the subwoofer SW (HORUS 8S)

The subwoofer should be placed between the two front speakers, either on the left or right of the center speaker, and away from the wall.

1. Connections on Home-Cinema amplifier and Home-cinema preamplifier.

WARNING: ALL THE CONNECTIONS MUST BE MADE WITH THE EQUIPMENT TURNED OFF.

It is essential to connect the speakers using the correct polarity. Make sure to connect the
“ + ” terminal of the speaker (Red) to the “ + ” output terminal of the amplifier. Then, make
sure to connect the “ – ” terminal of the speaker (Black) to the “ – ” output terminal of the amplifier. A wrong connection would cause a cribled stereo image and loss of bass. Use high quality speaker cable.

• FR/FL

| FRONT RIGHT/LEFT| Speaker Front right (R) /Left (L)

• C

| CENTER| Central Speaker

• SR/SL

| SURROUND RIGHT/LEFT| Surround speaker right (R) /Left (L)

• •SW

| SUBWOOFER| Subwoofer

USE

Burn-in period

When you take them out of the packaging, the Horus speakers are not yet able toreproduce with the same efficiency all the sound frequencies they are supposed to play. The Horus range loudspeakers are complex mechanical assemblies which need a period of adaptation (“burn-in”) to operate at their best and become acclimatized to the temperature and humidity conditions of your environment. This burn-in period may last for some weeks, but you can quicken it by operating the speakers between 50 and 100 hours consecutively, on a moderate volume and broadcasting a radio station.

Choice of cables

Choose high quality cables with a cross-section appropriate to their length. Your Elipson dealer will be able to advise you.

Choice of amplifier

Your setup type (stereo or home cinema) will determine the choice of the appropriate amplifier. Your dealer will be able to advise you on the most suitable amplifier for your system.

Cleaning instructions

To improve the lifetime of your speakers, we recommend regular cleaning. A soft cloth will be enough for dusting. If the speaker is stained, we recommend simply using a damp cloth with some mild soap if necessary. Never use solvents, detergents, alcohol-based or corrosive products, scrapers or scourers to avoid any damage on the speaker surface. Keep the loudspeakers away from sources of heat.

SPECIFICATIONS

Type| Bookshelf loudspeaker 2-way

Bass-reflex

| Floorstanding loudspeaker

2.5 way Acoustics Bass-reflex

| Center loudspeaker 2-way

Bass-reflex

---|---|---|---
Power| 70 W RMS| 120 W RMS| 100 W RMS
Power amplifier| 30 – 120 W| 50 – 200 W| 30 – 150 W

Loudspeakers

| Tweeter: 1” silk dome Neodynium

Mid-woofer: 5” Mixed of glass fiber and paper

| Tweeter: 1” silk dome Neodynium

Mid-woofers: 2×5” Mixed of glass fiber and paper

| Tweeter: 1” silk dome Neodynium

Mid-woofers: 2×5” Mixed of glass fiber and paper

Frequency response| 55 – 25 000 Hz| 40 – 25 000 Hz| 52 – 25 000 Hz
Sensitivity| 87 dB / 1W / 1m| 90 dB / 1W / 1m| 91 dB / 1W / 1m
Impedance| 8 Ohms| 6 Ohms| 6 Ohms

Packaging

The packaging (box and packing) was designed for effective protection of your Elipson loudspeakers and electronics during transportation and shipping. Please save them for later use.

Protect the environment

If you wish to dispose of the packaging, please do so in the most environmentally responsible manner possible according to available measures (for example, sorted recycling). At the end of its life, this device should not be disposed of the same way as household refuse. It should be returned to a center for the recycling of electronic equipment. This symbol on the product indicates that it has been designed so that it can be recycled according to specific procedures. You will therefore be making a significant contribution to the protection of the environment. This device respects the RoHS European directive. This means that it does not emit polluting substances when it is recycled (such as lead, mercury, cadmium, hexavalent chromium, polybromobiphenyles, polybromdiphenylethers).

Precautions for proper use

This product was designed according to rigorous norms and complies with safety standards. It should only be used under normal conditions as described below. Verify the electrical voltage before connecting it to a power source. This electronic device was designed to work in numerous countries. We advise you to hook it up completely before connecting it to the AC power source. Take care when unplugging the power cord. When you unplug the power cord from the power source, do so by pulling on the head of the plug rather than on the cable. If you do not expect to use this device for a prolonged period of time, you are advised to unplug it from the power source. Do not open the case. This device contains no parts that can be exchanged by the user. Accessing the inside of this device’s case can lead to electric shock. Any modification to the product will nullify the guarantee. If a foreign object or liquid falls into the case, contact your retailer to arrange for a technician to remove it from the device safely.

WARRANTY

Elipson speakers has been designed and manufactured to the highest quality standards. If something goes wrong with your product, Elipson or its authorized distributor / dealer will handle the service and repair under these limited warranty terms. This limited warranty is valid for a 2-year period from original purchase date from an authorized Elipson dealer.

Terms of limited warranty

The warranty is limited to equipment repair. Neither transportation, nor any other costs, nor any risk for removal, transportation and installation of products is covered by this warranty. The warranty is only valid for the original purchaser and is not transferable. The warranty will not apply in cases other than defects in materials and / or workmanship at the date of purchase and will not be applicable in the following cases:

• Damages caused by wrong or incorrect installation or connection.
• Damages caused by incorrect use, other use than the one described in the owner’s manual, negligence, unauthorized modification or use of parts or of accessories that are not authorized by Elipson.
• Damages caused by unauthorized, unsuitable or faulty ancillary equipment.
• Damages caused by accidents, lightning, water, fire, heat or any other disturbance that would not be under Elipson control or responsibility.
• For products, which serial number has been altered, deleted, removed or made illegible.
• In case of repair and service executed by an unauthorized service person.

This warranty complements any national/federal/regional law obligations of local distributors/dealers and does not affect your statutory rights as a customer.

To claim repair under warranty

To claim repair or service under warranty you simply have to contact your local Elipson dealer, from whom your equipment has been purchased. To ensure that you will be able to ship your damaged product in the correct manner, always retain the original packaging of your Elipson equipment. If you cannot contact your original dealer, or if you are using your Elipson product outside the purchase country, you should contact Elipson national distributor in the residence country, who will advise where the equipment can be serviced.

You can also visit our website to check our contact information: www.elipson.com

To validate your warranty, you need to produce, as proof of purchase, your original purchase invoice specifying the date of purchase and stamped by your dealer.

© Elipson 2023
Elipson is a registered trademark of AV Industry.

07/12/2022

www.elipson.com

References

• Elipson - High end loudspeakers

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>