AUTEL AR82060326 Smart Controller SE User Guide

AUTEL AR82060326 Smart Controller SE

Disclaimer

To ensure safe and successful operation of your Autel Smart Controller SE (hereinafter referred to as the “controller”), please strictly follow the operating instructions and steps in this guide. If the user does not abide by the instructions, Autel Robotics will not be responsible for any product damage or loss in use, whether direct or indirect, legal, special, accident or economic loss (including but not limited to loss of profit) and does not provide warranty service. Do not use incompatible parts or use any method that does not comply with the official instructions of Autel Robotics to modify the product. The safety guidelines in this document will be updated from time to time. To ensure you get the latest version, please visit the official website: https://www.autelrobotics.com/

Battery Safety

The controller is powered by a smart lithium-ion battery. Improper use of lithium-ion batteries can be dangerous. Please ensure that the following battery usage, charging and storage guidelines are strictly followed.

Note

• Only use the battery and charger provided by Autel Robotics. It is forbidden to modify the battery assembly and its charger or use third-party equipment to replace it.
• The electrolyte in the battery is extremely corrosive. If the electrolyte spills into your eyes or skin accidentally, please rinse the affected area with clean water and seek medical attention immediately.

Precaution

If used improperly, the aircraft may cause injury and damage to people and property. Please be cautious while using it. For details, please refer to the aircraft’s disclaimer and safety guidelines.

• Before each flight, make sure that the controller is fully charged.
• Make sure the controller antennas are unfolded and adjusted to the appropriate position to ensure the best possible flight results.
• If the controller antennas are damaged, it will affect the performance. Please contact the after-sales technical support immediately.
• If the aircraft is changed due to damage, it needs to be relinked before use.
• Make sure to turn off the aircraft power before turning off the controller each time.
• When not in use, make sure to fully charge the controller every three months.
• Once the power of the controller is less than 10%, please charge it to prevent an over-discharge error. This is caused by long-term storage with a low battery charge. When the controller will not be in use for an extended time, discharge the battery between 40%-60% before storage.
• Do not block the vent of the controller to prevent overheating and diminished performance.
• Do not disassemble the controller. If any parts of the controller are damaged, contact Autel Robotics After-Sale Support.

Item List

Overview

The Autel Smart Controller SE is integrated with a 6.4-inch touch screen which boasts a 2340×1080 pixel resolution. The controller f can transmit a live HD view from the aircraft [1] at a distance of up to 15km[1] (9.32 miles). The controller uses the Android operating system and supports Wi-Fi internet connection, Bluetooth and GNSS. Users can download third-party APPs. The built-in battery has a capacity of 1900mAh, providing a maximum operating time of about 3 hours[2]. [1] In an actual flight environment, the maximum transmission range may be less than this nominal distance and will vary with the interference strength. [2] The above-mentioned operating time is measured in a lab environment at room temperature. The battery life will vary in different usage scenarios.

Diagram

1. Left Control Stick
2. Gimbal Pitch Dial
3. Customizable Button
4. Chest Strap Hook
5. Air Outlet
6. USB-A Port
7. USB-C Port
8. Micro-SD Card Slot
9. HDMI Port
10. Record/Shutter Button
11. Zoom Control Wheel
12. Right Control Stick
13. Power Button
14. Antenna
15. Microphone
16. Touch Screen
17. Auto-takeoff/RTH Button
18. Pause Button
19. Battery Level Indicator
20. Speaker Hole
21. Tripod Mount Hole
22. Air Inlet
23. Handle
24. Sticks Storage Slot
25. Battery Case

Charge the Battery

Check the Battery Level
Press the power button to check the battery level.

Power On / Off
Press and hold the power button for 2 secs to turn on and off eth controller.

Charge
Connect one end of the USB-C cable to the USB-C interface at the top of the controller, and the other end to power adapter. Plug the power adapter into AC power outlet (100-240V).

Note

• LED indication light will blink while charging.
• Only use the battery and charger provided by Autel Robotics.
• Recharge the battery at least every 3 months to prevent over discharging. The battery depletes when stored for an extended period.

Set Up the Controller

Install the Sticks
The sticks storage slots are located on the back of the controller. Please take out the sticks and screw them into the corresponding bases.

Adjust the Antennas

Unfold the controller antennas and adjust them to the optimal angle. The signal strength varies when the antenna angle is different. When the antenna and the back of the controller are at an angle of 180° or 270°, and the antenna surface is facing the aircraft, the signal quality between aircraft and controller will reach the optimal condition.

Note

• To avoid controller signal interference, please do not use other communication equipment with the same frequency band at the same time.
• During operation, the App will prompt the user when the image transmission signal is poor. Adjust the antenna angles according to the prompts to ensure the controller and aircraft have the best communication range.

Pair the Frequency

1. Press (short press) the linking button next to the USB port on the right side of the aircraft body to put the aircraft into the linking mode.
2. Power on the Smart Controller and run the Autel Explorer app, enter the mission flight interface, click the gear icon in the upper right corner, enter the settings menu, click “remote control -> data transmission and image transmission linking> start linking”, wait a few seconds until the data transmission is set correctly and the linking is a success.

Takeoff / Landing (Mode 2)

Note

• Mode 2 is the default control mode of the Smart Controller. The left stick controls the altitude and heading of the aircraft, while the right stick controls the forward, backward and sideward movements.
• Before takeoff, place the aircraft on a flat and level surface and face the rear side of the aircraft towards you.
• Please make sure that the controller is successfully paired with the aircraft.

Motor Starting
Press in or out on both command sticks for about 2 seconds to start the motors .

Take off
Slowly push up the left stick to take off the aircraft to 2.5m height.

Landing
Slowly push down the left stick until the aircraft lands. Hold the left stick until the motor stops.

Control Stick Operation (Mode 2)

Firmware Update

To ensure users have a premium operating experience, Autel Robotics will update firmware when necessary. You can refer to the following steps to upgrade.

1. Power on the controller and make sure it is connected to the internet.
2. Run Autel Explorer App. A pop-up will appear when new firmware is available. Tap the notification to enter the update interface.
3. Update will start automatically after downloading the latest firmware. Please restart the controller when the update is complete.

Note

• Before updating, please make sure the controller battery is above 50%.
• If the network is disconnected during the firmware downloading, the upgrade will fail.
• The update takes approximately 15 minutes. Make. Please wait patiently.

Specifications

Image Transmission

• Operating Frequency

  • 902-928MHz（FCC）

  • 2.400-2.4835GHz

  • 5.725-5.850GHz（Non-Japan）

  • 5.650-5.755GHz（Japan Only）

• Max Signal Transmission Distance(No interference, No obstacles)

  • FCC：15km CE：8km

• Transmitter Power (EIRP)

  • FCC：≤33 dBm
  • CE：≤20 dBm@2.4G，≤14 dBm@5.8G
  • SRRC：≤20 dBm@2.4G，≤33dBm@5.8G/5.7G

Wi-Fi

• Protocols
  • Wi-Fi 802.11a/b/g/n/ac, 2×2 MIMO
• Operating Frequency
  • 2.400-2.4835GHz
  • 5.725-5.850GHz
• Transmitter Powe
  • FCC：≤26 dBm
• (EIRP)
  • CE：≤20 dBm@2.4G，≤14 dBm@5.8G SRRC：≤20 dBm@2.4G，≤26 dBm@5.8G

Bluetooth

• Protocols
  • Bluetooth 5.0
• Operating Frequency
  • 2.400-2.4835GHz
• Transmitter Power (EIRP)
  • ≤11dBm

Screen

• Resolution
  • 2340×1080
• Dimensions
  • 6.4 inches
• Frame Rate
  • 60fps
• Max. Brightness
  • 800nits
• Touch Screen
  • 10-point multi-touch

Battery

• Type
  • Li-ion
• Capacity+
  • 1900mAh
• Voltage
  • 7.7V
• Rated Power
  • 14.63W
• Operating Time
  • ~2 hours (Max. Brightness)
  • ~3 hours (50% Brightness)
• Charging Time
  • 90 minutes
• Charging Temperature
  • 5℃ to 45℃（41℉ to 113℉）

General Specifications

• Internal Storage

  • ROM 128GB + expandable storage via micro-SD card

• Video Output Port

  • HDMI Port

• USB-A Voltage/Current

  • 5V/2A

• Operating Temperature

  • -20℃ to 40℃ (14℉ to 104℉)

• Storage Temperature

  • 3 months: -20℃ to 25℃（-4℉ to 77℉）

  • 1-3 months: -20℃ to 45℃（-4℉ to 113℉）
  • <1 month: -20℃ to 60℃（-4℉ to 140℉）

• Ingress Protection

  • IP43

• Dimensions

  • 226.3×137.7×31.5mm (antennas folded)

  • 226.3 x 215.4 x 31.5mm (antennas unfolded

• Weight

  • 617 g

• **Supported Models

  • EVO II Pro V3
  • EVO II Dual 640T V3
  • EVO II RTK Series V3
  • EVO II Enterprise V3

• GNSS

  • GPS/GLONASS/Galileo/BeiDou/ NavIC/QZSS

Note

• The operating frequency band varies according to different countries and models.
• We will support more models in the future, please visit our official website https://www.autelrobotics.com/ for the latest information.www.autelrobotics.com 2022 Autel Robotics Co., Ltd. All Rights Reserved.

References

• My Blog – My WordPress Blog
• ICS - Integrated Computer Solutions
• Autel Robotics Enterprise Drone, Quadcopter & UAV for Sale
• Autel Robotics Enterprise Drone, Quadcopter & UAV for Sale

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>