U-PROX SE Maxi Versatile Reader Instructions
- June 3, 2024
- U-PROX
Table of Contents
**U-PROX SE Maxi Versatile Reader Instructions
**
Instructions
- mobile credentials
- NFC and 2.4 GHz radio
- adjustable 2.4 GHz distance (0.1 – 15 m)
- Mifare Plus SL1/SL3 and Mifare Classic
- supports multiple formats of 125 kHz RFID
- smartphone adjustable
- adjustable OSDP/Wiegand interface
- convinient and safe
- simple and convenient installation
- IP65 degree of protection
The adjustable versatile SmartLine second edition (SE) reader for mobile credentials and proximity identifiers in conjunction with the U-Prox Mobile ID application and U-Prox IDs will allow any access control system to use smartphones as access system credentials.
U-Prox ID
Digital personal mobile credential. It is processed and stored in the user’s smartphone using the U-Prox Mobile ID application. It can be transferred over NFC and/or 2.4 GHz radio between the reader and the smartphone.
via NFC for Android only
Read range 2-5 cm. Recommended for double-sided doors and turnstiles.
via 2.4 GHz radio for Apple and Android
Reader supports 3 operation modes for smartphones with U-Prox ID:
-
“Door-Proximity” – 10-20 cm, reader activates by built-in IR sensor.
Recommended for double-sided doors and turnstiles -
“Door” – up to 60-70 cm
-
“Barrier/Gate” – adjustable range of interaction from 1 to 15 m
Mifare® и Mifare®Plus
Operates with ISO14443A identifiers, supports SL1 and SL3 modes for
Mifare®Plus. Read range — up to 5 cm.
Reads encrypted identifiers with static or diversified key and with an
arbitrary card number.
Simultaneous use of five encryption profiles.
RFID, 125 kHz
Supports RFID 125 kHz – EmMarine and other formats.
Easy connection
Seamless and easy connection to existing and new access systems, due to the OSDP, Wiegand 26, 32, 34, 37, 40, 42, 56, 58, 64, 80 bit interfaces, Wiegand with automatic selection, RS232 and TouchMemory supports.
Integration
OSDP or RS-232 protocols for integration into arbitrary systems.
The encrypted OSDP protocol provides safe management of all parameters of the
reader including credential encryption keys from the panel.
Mobile Apps
Free mobile application U-Prox Mobile ID receives, stores and transmits mobile credentials U-Prox ID between the reader and the smartphone.
With the free mobile application U-Prox Config, the reader can be completely adjusted — from the indication to the encryption modes.
The reader is supplied without the engineering password for programming specified. To connect and (re) set the password — connect inputs D0 (green) and D1 (white) with each other and apply power to the reader.
Warning!!! The reader firmware can be updated with an NFC-enabled Android smartphone only.
Benefits
Read range| NFC, Mifare and RFID 125 kHz – up to 5 cm, 2.4 GHz radio –
adjustable 10 cm – 15 m
---|---
Mifare®, 13.56 MHz| IS014443A: Mifare®Standard, Mifare0Hi-Memory,
Mifare0Ultralight, Mifare®Classic 1K/4K, Mifare®Classic 7UID, Mifare® Plus S
2K, Mifare® Plus S 4K, Mifare® Plus SE 1K, Mifare® Plus X 2K, Mifare® Plus X
4K, Mifare® Plus EV1 2K, Mifare® Plus EV1 4K, Mifare® DESfire, Mifare® DESfire
EV1, Mifare® DESfire EV2
NFC, 13.56 MHz| ISO 14443/15693
RFID, 125 kHz| ASK and FSK
Case material & Color| ABS+PC plastic, black
Dimensions| 42.8 x 157.8 x 16 mm
Weight| 120 g
Ambient| IP65, -40°C … +60°C
Power supply| +9… +15 VDC, max current- up to 90 mAVoltage ripple – up
to 500 mVp-p
Interfaces| OSDP, Wiegand Auto, 26, 32, 34, 37, 40, 42, 56, 58, 64, 80
bits, RS232 and TouchMemory
Wiring| 8 wire cable, maximum distance to panel – up to 150 m for
Wiegand interface, up to 30 M m for TouchMemory interface, up to 1000 m for
OSDP interface
Wiring
The reader connection wires functions are listed in the table. We recommend to use multi-core signal cable with 0.22 mm² cross-section of each wire between reader and panel.
Color | Wiegand | RS232 | TouchMemory | OSDP |
---|---|---|---|---|
Green | Data0 (WD0) | Rx iButton | A+ | |
White | Data1 (WD1) | Tx | B- | |
Red | +V, 12 VDC | |||
Black | GND | |||
Brown | Red Led | Red Led | ||
Orange | Green Led | Green Led | ||
Blue | Beep | Beep | ||
Yellow | Hold/Sync | Hold/Sync Hold/Sync |
Reader turns to the hold mode while yellow wire is shorted to ground and does
not read any identifiers.
It is prohibited to supply the external voltage to the yellow wire!
Reader connection to the panel with twisted pair.
Reader Installation
Installation on the metal surfaces without the supplied plastic wafer may
cause decrease of reading range. Do not place readers closer than 20 cm one
from another. It is possible to install two readers at a distance 10-15 cm of
each other when their yellow wires (Hold/Sync) interconnected. This
synchronizes the work of the readers, they will work alternately.
- Make small recess or hole (diameter is 14 mm) to connect cable under the reader’s case
- Loosen the screw at the bottom of the reader
- Remove the top cover
- When mounting on a metal surface, use the plastic wafer
- Carry out wiring to the control panel
- Fasten the reader to the wall, using supplied plastic dowels and screws
- Place the top cover and tighten it with a screw
Limited Warranty
The reader connection wires functions are listed in the table. We recommend to
use multi-core signal cable with 0.22 mm² cross-section of each wire between
reader and panel.
Manufacturer warrants that for a period of thirty six months from the date of
purchase, the product shall be free of defect in materials and workmanship
under normal use and that in fulfillment of any breach of such warranty,
Integrated Technical Vision ltd. shall, at its option, repair or replace the
defective equipment upon return of the equipment to its repair depot. This
warranty applies only to defects in parts and workmanship and not damages
incurred in shipping or handing, or damages due to causes beyond the control
of Manufacturer such as lightning, excessive voltage, mechanical shock, water
damage, or damage arising out of abuse, alteration or improper application of
the equipment.
The foregoing warranty shall apply only to the original buyer, and is and
shall be lieu of any and all other warranties, whether expressed or implied
and of all other obligations or liabilities on the part of Manufacturer This
warranty contains the entire warranty. Manufacturer neither assumes, nor
authorizes any other person purporting to act on its behalf to modify or to
change this warranty, nor to assume for it any warranty or liability
concerning this product.
In no event shall Manufacturer be liable for any direct, indirect or
consequential damages. Loss of anticipated profits, loss of time or any other
losses incurred by the buyer in connection with the purchase, installation or
operation or failure of this product.