HYDROPOOL Signature Self Cleaning Hot Tubs Owner’s Manual

Signature Self Cleaning Hot Tubs

SIGNATURE SELF CLEANING HOT TUBS OWNER’S MANUAL
Hydropool Inc. 335 Superior Blvd. Mississauga, ON, Canada L5T 2L6 Tel: 905.565.6810 Toll Free: 1.800.465.2933 Fax: 905.565.6820 Email: info@hydropoolhottubs.com www.hydropoolhottubs.com Contents subject to change without notice
2023

Models Covered
Self Clean 395 Gold Self Clean 495 Gold Self Clean 495 Platinum Self Clean 570 Gold Self Clean 570 Platinum Self Clean 670 Gold Self Clean 670 Platinum Self Clean 695 Gold Self Clean 695 Platinum Self Clean 720 Platinum Self Clean 770 Platinum Self Clean 790 Platinum Self Clean 970 Titanium

Domestic Model Codes
HSC395G HSC495G HSC495P HSC570G HSC570P HSC670G HSC670P HSC695G HSC695P HSC720P HSC770P HSC790P HSC970T

Export Model Codes HSCE395G HSCE495G HSCE495P HSCE570G HSCE570P HSCE670G HSCE670P HSCE695G HSCE695P HSCE720P HSCE770P HSCE790P HSCE970T

2

TABLE OF CONTENTS

Letter of introduction
Important User Safety Instructions Warnings Hyperthermia
Choosing the Right location Indoor Locations Outdoor Locations
General Installation Considerations
Special Considerations Indoor Installations Outdoor Installations
Site Preparation Above Ground Installations In-ground & Partial In-ground Installations Overall Support (non-cabinet installations)
Equipment Accessibility & Protection
Unloading/Handling your Hot Tub
Important Electrical Safety Instructions G.F.C.I./R.C.D. Application Guideline Wire Size North America G.F.C.I. Installation Diagram Europe R.C.D. Installation Diagram
Filling, Checking and Starting your Hot Tub Pump Priming/Releasing an Air Lock
Hydropool Control Systems
IN.YE / IN.YT Spa Pack Series I-Command 2 System (optional) Standby Mode / Drain Mode Hydrother Control / Wellness Package (optional)
Topside Panel Display Messages
Optional Variable Air Therapy System

4
5 6
7 7
8
9 9
9 10 10
11
11
12 12 13 14 15
16-17 16-17
18-25
18-38 26 37 37
38
38

Hydroclear Pure Water System

39

UV-C Lamp Replacement Instructions

40

Hot Tub Water Balance

General Overview

41

Initial Fill

41

Glossary of Common Water Maintenance Terms

42

Water Balance Summary for your Hot Tub (chart) 42

Water Balance Troubleshooting

43

Routine Hot Tub Maintenance

Daily, Weekly, Monthly, Quarterly

44

Cleaning the Skimmer Basket

44

Safety Hard Cover

44

Cartridge Filter, Removal, Cleaning, Re-installation 45

Cleaning the Acrylic Surface

45

Changing your Hot Tub Water

46

Draining your Hot Tub Water

46

Hydropool Exclusive Quick-DrainTM

47

Self-Cleaning Mode Indicator

47

Everlast Products

Protecting your Cabinet Everlast Finish

48

Winterizing your Hydropool Hot Tub

49

General Troubleshooting

50

What to do in the event of

Power Fluctuations

50

Cold Weather Power Failure

50

Wiring Diagrams (in.ye / in.yt )

51-56

NOTE: Product specifications, warnings and labels are subject to change without notice. This user’s manual should be used as a guide only. For further information, please contact your independent Hydropool dealer.
3

On behalf of everyone at the company, we thank you for your decision to purchase a Hydropool hot tub. Recognized for quality worldwide, we are confident that your new hot tub will provide you, your family and friends, with years of enjoyment and fulfill all your hydrotherapy needs. Hydropool hot tubs are not only healthful and relaxing, they can even add value to your home. Please take the me to carefully read and understand all the safety, installa on and opera ng instruc ons in this manual before electrically connec ng your hot tub and adding water. The following pages contain valuable informa on and pointers that will save you both me and money, as well as help you to simplify upkeep and maintenance. Since we manufactured our first hot tub in 1985, the Hydropool team has been dedicated to producing a quality product catering to maximum hydrotherapy, comfort, energy efficiency and ease of opera on. We are confident that as you become more familiar with the various safety and maintenance features of your new hot tub you will be sa sfied that you made the right decision in purchasing a Hydropool hot tub. Happy hot tubbing…
David Jackson
4

SAVE THESE INSTRUCTIONS
IMPORTANT SAVE THESE INSTRUCTIONS
Your physiological response to hot water is subjec ve and depends on your age, health, and medical history. If you don’t know your tolerance to hot water, or if you get a headache, or become dizzy or nauseous when using your hot tub, get out
and cool off immediately.
WARNING
1. CHILDREN SHOULD NOT USE SPAS OR HOT TUBS WITHOUT ADULT SUPERVISION. 2. DO NOT USE SPAS OR HOT TUBS UNLESS ALL SUCTION GUARDS ARE INSTALLED TO PREVENT BODY AND HAIR
ENTRAPMENT. 3. PEOPLE USING MEDICATIONS AND/OR HAVING ANY ADVERSE MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN
BEFORE USING A SPA OR HOT TUB. 4. PEOPLE WITH INFECTIOUS DISEASES SHOULD NOT USE A SPA OR HOT TUB. 5. TO AVOID INJURY, EXERCISE CARE WHEN ENTERING OR EXITING THE SPA OR HOT TUB. 6. DO NOT USE DRUGS OR ALCOHOL BEFORE OR DURING THE USE OF A SPA OR HOT TUB, TO AVOID UNCONSCIOUSNESS
AND POSSIBLE DROWNING. 7. PREGNANT OR POSSIBLE PREGNANT WOMEN SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA OR HOT TUB. 8. WATER TEMPERATURE IN EXCESS OF 38°C (100°F)MAY BE INJURIOUS TO YOUR HEALTH. 9. BEFORE ENTERING THE SPA OR HOT TUB, MEASURE THE WATER TEMPERATURE WITH AN ACCURATE THERMOMETER. 10. DO NOT USE A SPA OR A HOT TUB IMMEDIATELY FOLLOWING STRENUOUS EXERCISE. 11. PROLONGED IMMERSION IN A SPA OR HOT TUB MAY BE INJURIOUS TO YOUR HEALTH. 12. DO NOT PERMIT OR USE ELECTRIC APPLIANCES (SUCH AS LIGHT, TELEPHONE, RADIO OR TELEVISION) WITHIN 1.5M
(5FT) OF THIS SPA OR HOT TUB. 13. CHILDREN SHOULD NOT ENTER A HOT TUB WHERE THE WATER TEMPERATURE EXCEEDS BODY TEMPERATURE (37°C /
98.6°F). 14. DO NOT ALLOW CHILDREN TO SUBMERGE THEIR HEAD UNDER WATER. 15. NEVER OPERATE THE HOT TUB PUMP AT HIGH SPEED WITHOUT HAVING ALL SUCTION AND RETURN LINES OPEN. 16. ALWAYS KEEP THE HARDCOVER INSTALLED AND LOCKED WHEN THE HOT TUB IS NOT IN USE. 17. TEST THE GFCI (GROUND FAULT CIRCUIT INTERRUPTER) MONTHLY. 18. POST EMERGENCY PHONE NUMBERS FOR POLICE, FIRE DEPARTMENT, AND AMBULANCE AT THE NEAREST PHONE. 19. TO REDUCE THE RISK OF INJURY
· THE WATER IN A SPA SHOULD NEVER EXCEED 40°C (104°F). WATER TEMPERATURES BETWEEN 38°C (100°F) AND 40°C (104°F) ARE CONSIDERED SAFE FOR A HEALTHY ADULT. LOWER WATER TEMPERATURES ARE RECOMMENDED FOR YOUNG CHILDREN AND WHEN SPA USE EXCEEDS 10 MINUTES.
· SINCE EXCESSIVE WATER TEMPERATURES HAVE A HIGH POTENTIAL FOR CAUSING FETAL DAMAGE DURING THE EARLY MONTHS OF PREGNANCY, PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD LIMIT SPA WATER TEMPERATURES TO 38°C (100°F).
· BEFORE ENTERING A SPA, THE USER SHALL MEASURE THE WATER TEMPERATURE SINCE THE TOLERANCE FOR WATER TEMPERATURE-REGULATING DEVICES VARIES.
· THE USE OF ALCOHOL, DRUGS, OR MEDICATION BEFORE OR DURING SPA USE MAY LEAD TO UNCONSCIOUSNESS, WITH THE POSSIBILITY OF DROWNING.
· OBESE PERSONS AND PERSONS WITH A HISTORY OF HEART DISEASE, LOW OR HIGH BLOOD PRESSURE, CIRCULATORY SYSTEM PROBLEMS OR DIABETES SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA.
· PERSONS USING MEDICATION SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA SINCE SOME MEDICATION MAY INDUCE DROWSINESS WHILE OTHER MEDICATION MAY EFFECT HEART RATE, BLOOD PRESSURE AND CIRCULATION.
5

SAVE THESE INSTRUCTIONS
IMPORTANT SAVE THESE INSTRUCTIONS Your physiological response to hot water is subjec ve and depends on your age, health, and medical history. If you don’t know your tolerance to hot water, or if you get a headache, or become dizzy or nauseous when using your hot tub, get out
and cool off immediately.
CAUTION

1. MAINTAIN WATER CHEMISTRY IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS.
DANGER

1. RISK OF ACCIDENTAL DROWNING. EXTREME CAUTION MUST BE EXERCISED TO PREVENT UNAUTHORIZED ACCESS BY CHILDREN. TO AVOID ACCIDENTS, ENSURE THAT CHILDREN CAN’T USE THE SPA UNLESS THEY ARE SUPERVISED AT ALL TIMES.
2. RISK OF INJURY. THE SUCTION FITTINGS IN THIS SPA ARE SIZED TO MATCH THE SPECIFIC WATER FLOW CREATED BY THE PUMP. SHOULD THE NEED ARISE TO REPLACE THE SUCTION FITTINGS OR THE PUMP, BE SURE THAT THE FLOW RATES ARE COMPATIBLE. NEVER OPERATE THE SPA IF THE SUCTION FITTINGS ARE BROKEN OR MISSING. NEVER REPLACE A SUCTION FITTING WITH ONE RATED LESS THAN THE FLOW RATE MARKED ON THE ORIGINAL SUCTION FITTING.
3. RISK OF ELECTRIC SHOCK. INSTALL AT LEAST 1.5M (5FT) FROM ALL METAL SURFACES. AS AN ALTERNATIVE, A SPA MAY BE INSTALLED WITHIN 1.5M (5FT) OF METAL SURFACES IF EACH METAL SURFACE IS PERMANENTLY CONNECTED BY A MINIMUM 8 AWG (8.4 mm2) SOLID COPPER CONDUCTOR TO THE WIRE CONNECTOR ON THE TERMINAL BOX THAT IS PROVIDED FOR THIS PURPOSE.
4. RISK OF ELECTRIC SHOCK. DO NOT PERMIT ANY APPLIANCE, SUCH AS A LIGHT, TELEPHONE, RADIO, OR TELEVISION, WITHIN 1.5M (5FT) OF THE SPA.

HYPERTHERMIA Since your hot tub can be set to reach temperatures of 40°C (104°F), users should be aware that extended submersion in water that exceeds normal body temperature can lead to hyperthermia.
The causes, symptoms and effects of hyperthermia may be described as follows: Hyperthermia occurs when the internal temperature of the body reaches several degrees above the normal body temperature of 37°C (98.6°F). The symptoms of hyperthermia include drowsiness, lethargy, and an increase in the internal temperature of the body. The effects of hyperthermia include:

WARNING
THE USE OF ALCOHOL, DRUGS OR MEDICATION CAN SIGNIFICANTLY INCREASE THE RISK OF FATAL HYPERTHERMIA.

· Unawareness of impending hazard · Failure to perceive heat · Failure to recognize the need to exit the hot tub · Physical inability to exit the hot tub · Fetal damage in pregnant woman · Unconsciousness resul ng in the danger of drowning
If you sense any of the symptoms of hyperthermia, safely exit the hot tub immediately.
6

CHOOSING THE RIGHT LOCATION
Your Hydropool hot tub can be installed indoors or out, on the ground, in the ground or half-and-half. The following informa on will assist you in choosing the right loca on for your individual needs. When making your decision, always remember that hot tubs can be enjoyed year-round, indoors or out, regardless of the climate. Many Hydropool owners report that their favourite me to use a hot tub is in the cooler fall and winter months, while others praise the enjoyment
of using their hot tub in the warmer spring and summer months. INDOOR LOCATIONS
If members of your family are not cold weather enthusiasts, or if your backyard or pa o area is not suitable for a hot tub installa on, then an indoor loca on for your hot tub may be your best or only choice. You may wish to create an exercise/spa area in your home, or install your hot tub in a glass solarium or four-season room adjoining your home. Indoor installa ons not only add a unique look and appeal to your home, they provide the privacy and controlled climate to ensure that use and enjoyment of your hot tub is maximized. If you should choose an indoor loca on, you will find further informa on as outlined in the sec on “SPECIAL CONSIDERATIONS FOR INDOOR INSTALLATIONS”
OUTDOOR LOCATIONS For a variety of reasons, outdoor loca ons are a far more popular choice. Some of the reasons include: · Limited indoor space · Delivery complica ons due to door openings, stairwells, etc. · Limited budget (indoor installa ons usually also involve interior home renova ons) · Desire for an outdoor entertainment center · Hot tub is being installed adjacent to an exis ng or planned swimming pool · Concerns over splashing water inside the home For those who choose an outdoor loca on, hot tub opera ng temperatures can be adjusted to match the season. In colder months, many owners will operate their hot tub in the range of 38-40°C (100 -104°F). During warmer months, an opera ng temperature of 36-37°C (97-99°F) will provide a refreshing retreat. If you should choose an outdoor loca on, you will find further informa on as outlined in the sec on “SPECIAL CONSIDERATIONS FOR OUTDOOR INSTALLATIONS”
7

GENERAL INSTALLATION CONSIDERATIONS
1. Your HYDROPOOL hot tub is a self-contained pre-plumbed unit, so that no on-site plumbing connec ons to the residen al water supply or drain are required.
2. Ensure that your HYDROPOOL hot tub is properly supported by either a level concrete pad, or a properly constructed deck capable of suppor ng 1220 kg/m2 (250 lbs./ .2). If there is a possibility that the pad could shi by freezing/thawing ground movement (such as in clay regions, and/or areas with high water tables) concrete foo ngs extending below the frost line are recommended.
3. Decking should be chosen and constructed in a manner that minimizes the chance of slipping or falling. 4. If you do not have a factory installed insulated cabinet, it is assumed that you are building your own custom cabinet,
ling or decking. Please consider the following: a) Your HYDROPOOL hot tub is self-suppor ng on its base. The cabinet should be decora ve only, not for support. Never
suspend the hot tub from the deck or cabinet. b) Where the hot tub is not equipped with a factory installed cabinet, it is the installer’s responsibility to ensure all electrical
equipment is completely weather protected and meets all of the regulatory requirements. c) Always provide adequate access for servicing the support equipment. d) Decking must be constructed to allow repair access around the en re hot tub. e) In remote equipment or no-cabinet installa ons, you may add extra insula on, but the equipment area must have
adequate cross-flow ven la on. 5. Installa on of a safety grab rail or reachable support for use when entering or exi ng the hot tub is recommended. 6. A nearby garden hose connec on is recommended for filling and “topping up” the hot tub.
WARNING
The hot tub equipment and all electrical plugs, outlets and lights within 1.5m (5 ) of the hot tub must be G.F.C.I protected. Consult your electrician or local electrical authority for further details. Access to the hot tub must always be secured: Outdoors – in accordance with local property by-laws and/or via an approved fence with a self-closing gate and a safety hardcover;
8

INDOOR INSTALLATIONS

SPECIAL CONSIDERATIONS

· It is beneficial to have the hot tub room located near wash room and shower facili es · The hot tub room should have a floor drain to handle splash water, a window, outside exhaust fan or humidistat controlled
exhaust fan for ven la on and a humidifier. · Consider plumbing a water tap and drain loca on nearby to facilitate draining and top-up · Always provide adequate ven la on for the support equipment · Consult your local Hydropool retailer for further informa on

OUTDOOR INSTALLATIONS
· Contact your local building code department to determine if a building permit is necessary and for informa on on applicable bylaws (distance from property lines, buildings, fencing requirements, etc.)
· If you are doing any excava ng, contact your local gas, electric, and cable- company to ensure that there are no underground lines
· Locate the hot tub, where prac cal, within close distance of a door to the house to maximize poten al winter use. · Ensure that all hot tub support equipment is easily accessible and protected from the elements · The hot tub support equipment is designed for indoor (out of the direct elements) use. When your HYDROPOOL hot tub is
equipped with a factory-installed cabinet, and installed as per the guidelines of this manual, the equipment will be adequately protected. If the hot tub is shipped without a cabinet, your custom cabinet or other structure must be designed to supply protec on for the hot tub support equipment from rain, snow, splash water, etc., but s ll designed in a manner to ensure adequate ven la on.

ABOVE-GROUND INSTALLATIONS

SITE PREPARATION

Where the hot tub is a “stand-alone” above-ground installa on to be installed in regions where freeze/thaw condi ons may occur, a level pa o stone or pre- formed paver type base may be sufficient if there is no abu ng deck(s) that could be damaged during poten al seasonal movement of the ground. The poten al drawback to this type of base is that splash water could eventually de- stabilize the ground under the base, with the resultant shi of the support base causing damage to the hot tub structure.

For best results, we recommend the installa on of a level concrete pad:
· Dig out and level the ground 20-30 cm (8-12 in.) below your desired base level. · Install 10-15 cm (4-6 in.) of crushed stone. · Next, install 10-15 cm (4-6 in.) of poured concrete. · Level the concrete and apply a broom-type finish. · We recommend that the pad be made 15 cm (6 in.) larger than the hot tub on three sides, and 1 m (3 .) larger on the
side where the access steps and/or planters will be installed. · Hot tub must be installed on a level pad

In regions where freeze/thaw occurs, or where there will be custom decking abu ng the hot tub we recommend the installa on of sono-tubes beneath the pad to prevent shi ing.

9

IN-GROUND & PARTIAL IN-GROUND INSTALLATIONS For units being installed fully or par ally in the ground, the type of support will again vary based on whether or not the tub is being installed in an area with freeze/thaw condi ons. Hydropool does not recommend back-filling full in-ground or par al in-ground installa ons. · Non-freezing climates ­ it is sufficient to ensure that the base of the hole or cavity created for the tub has a dry, stable,
compacted level base and proper drainage. · Climates where freeze/thaw occurs ­ it is necessary that a poured level reinforced concrete base, complete with
concrete foo ngs, be installed as outlined in the sec on ABOVE-GROUND INSTALLATIONS. Areas with a high ground water table ­ a level concrete base, as well as a concrete or wood retaining wall to hold back the earth, is recommended. This forms a box or `bunker’, in which the hot tub is placed. · ALWAYS ensure that there is good drainage, via a properly designed French drain (gravel) system and/or a sump pump,
to prevent ground water flooding damage to the support equipment or hot tub structure. · Install protec ve waterproof conduit to house any cables that will be buried. · Access for future service must be considered at the me of design and installa on. You must be able to access all sides
and areas of your hot tub. Difficult access will result in supplemental service labor charges not covered by the factory warranty. Consider easily removable deck materials. · Make sure the hot tub or swim spa is tested for 48 hours before you prepare the installa on of the surrounding/finish deck around your hot tub. Even though all units are tested in our plant, some transport/site handling damage can occur and we suggest you make sure the tub is perfectly waterproof before finalizing your installa on.
10

EQUIPMENT ACCESSIBILITY AND PROTECTION
The equipment must be located in an area where it will remain serviceable, dry and will not be exposed to rain, snow or ground water.
UNLOADING / HANDLING YOUR HOT TUB
All Hydropool hot tubs are shipped with a protec ve combina on layer of foam wrap, cardboard and plas c film. Each hot tub is factory strapped onto a wood skid. If your hot tub is to be delivered by your local dealer, it will generally arrive on a flat bed truck or low profile trailer. Most dealers are equipped with the necessary equipment to maneuver the hot tub from the truck to the dolly or cart that will be used to move your hot tub to the installa on loca on.
Should your hot tub arrive in a common closed box trailer, it may be necessary to arrange with a local towing company for a lt and load tow truck, with a pulley winch system, to pull the skid from the larger trailer to the lower profile tow truck flat
bed. The hot tub can be gently slid off the low profile trailer and posi oned on its side on a cart or dolly on its back side only.
Most Hydropool models require a clearance width of at least 100 cm. (39 in.) to allow movement of the unit on its side through alley-ways, fence openings, etc. Where this is not possible, the use of a crane to li the hot tub from the truck or trailer over the house to the pa o or yard is o en a simple and economical op on.
WARNING
· Do not move or place the hot tub on the side where the equipment is located as damage could occur. · Never roll or flip the hot tub end over end as the cabinet could be damaged. · Never li or handle the hot tub by the plumbing. · Make sure that there is sufficient assistance to gently slide the hot tub off the dolly or cart to the support base without
any damage.
Important Note: Damage caused during transporta on or by improper handling is not covered by the factory warranty.

Crane

Crane & Strap Spreader

11

IMPORTANT ELECTRICAL SAFETY INSTRUCTIONS
SAFETY COMES FIRST. WHEN INSTALLING & USING THIS ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS MUST ALWAYS BE FOLLOWED!

1. READ AND FOLLOW ALL INSTRUCTIONS
2. Electrical installa on must be completed by a qualified electrician in accordance with all Na onal, Regional and Local Codes and Regula ons in effect at the me of installa on.
3. Connect only to a dedicated circuit protected by a class `A’ two-pole ground fault circuit interrupter (GFCI) 4. Use copper conductors only! 5. The hot tub equipment and all electrical plugs, outlets and lights within 1.5m (5 ) of the unit must be G.F.C.I protected.
Consult your electrician or local electrical authority for further details. 6. A green colored terminal or a terminal marked “G”, “GR”, “Ground”, or “Grounding” is located inside the supply terminal
box or compartment. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a con nuous copper wire equivalent in size to the circuit conductors supplying the equipment. 7. At least two lugs marked “BONDING LUGS” are provided on the external surface or on the inside of the supply terminal box or compartment. To reduce the risk of electric shock, connect the local common bonding grid in the area of the hot tub to these terminals with an insulated or bare copper conductor not smaller than No.6 AWG (Canada/Europe) / No.8 AWG (USA). 8. All field installed metal components such as rails, ladders, drains or other similar hardware within 3 m (10 ) of the hot tub shall be bonded to the equipment grounding bus with copper conductors not smaller than No.6 AWG.

IMPORTANT NOTE:
· This guide is for standard installa ons where the wire run is 15 m (50 .) or less. For longer wire runs, consult a qualified electrician.

G.F.C.I./R.C.D. APPLICATION GUIDE FOR HYDROPOOL SELF CLEAN SERIES

NORTH AMERICA

Gold Series

40A

Pla num Series

50A

Titanium Series

60A

EUROPE

Gold Series

20A

Pla num Series

20A

Titanium Series

40A

FIGURE 1: ELECTRICAL CONDUIT LOCATION
IMPORTANT NOTE: (FIGURE 1)
The following dimensions can be used to determine the proper loca on of submerged conduits in concrete slab installa ons. The dimensions are made from the outside of the spa / hot tub frame with the access for panels removed. The topside control panel is shown at the bo om of the diagram as a reference.

12

WIRE SIZE NORTH AMERICA · The minimum wire size for systems that require a 40A GFCI is # 8/3 c/w ground (also referred to as # 8 gauge / 4 conductor). · The minimum wire size for systems that require a 50A GFCI is # 8/3 c/w ground (also referred to as # 8 gauge / 4 conductor). EUROPE Standards for amperage breakers may vary from country to country in the CE controlled area. Please consult your local installer for advice on breaker level and wire specifica ons. Some examples are below: Breaker of 13A ­wire must be 1.5 mm2 Breaker of 16A–wire must be 2.5 mm2 Breaker of 20A–wire must be 4.0 mm2 Breaker of 32A–wire must be 6.0 mm2 NOTE: Please consult your applicable electrical codes related to the size of conductors as they may vary from what is stated above. Take into considera on the length of cable as well and increase as required.
13

NORTH AMERICA ­ GFCI INSTALLATION
NOTICE
Installa on of the GFCI – Circuit Breaker, including ampere sizing and selec on of conductor size and type, must be performed by a qualified electrician in accordance with the Na onal Electrical Code, or the Canadian Electrical Code, and all Federal, State/Provincial and local codes and regula ons in effect at the me of installa on. Hydropool highly recommends the use of a new Siemens GFCI breaker for all of its products. Other GFCI’s and older Siemens GFCI’s may have tripping issues.
240 VOLT 60 Hz GFCI WIRING
14

EUROPE ­ R.C.D. INSTALLATION – TYPICAL
NOTICE
Important Note: Installa on of the R.C.D. – Circuit Breaker, including ampere sizing and selec on of conductor size and type, must be performed by a qualified electrician in accordance with Na onal, Regional and Local Codes and Regula ons in effect at the me of installa on. 230 VOLT 50 Hz SINGLE PHASE RCD WIRING
230 VOLT 50 Hz DUAL PHASE RCD WIRING
230 VOLT 50 Hz THREE PHASE RCD WIRING
15

FILLING, CHECKING AND STARTING YOUR HOT TUB

CHECKING
Although your hot tub was thoroughly water-tested in the factory, some loosening of fi ngs can occur during shipping. Before any decking, ling or carpe ng is completed around the installa on, fill and operate your hot tub to test for leaks (this ensures easy access and inexpensive correc on). Check all union connec ons and plumbing for minor leaks. In the event of a leak, ensure all union connec ons and pump plugs are ght and all o-rings/gaskets are in place.

UNIONS

STARTING
Before applying voltage to power-up your hot tub, it is very important that you understand the sequence of events that occur when the system is ac vated in order that the pump can be primed efficiently and damage to the system can be avoided. · Turn the main power “on” at your electrical panel. · Follow the control instruc ons for your par cular model
hot tub to put the pump into low speed. See sec on HYDROPOOL CONTROL SYSTEMS

HOSE BIB
PROPER WATER LEVEL
FILLING When adding water for the first me, the hot tub should be filled through the skimmer opening (helps to prevent air locks) using a standard garden hose, turning the tap on slowly to prevent damage to the surface by a jerking hose connec on. · Pull up the handles on the intake and return gate valves and clip on the stem locks. (handles are pulled up when valves are open and pushed down when valves are closed). · Ensure the drain hose-bib is closed. · Ensure that all jets are open. · Fill the hot tub to the recommended level as indicated
by the “MIN” and “MAX” marks on the weir door of the skimmer opening.

PUMP PRIMING/RELEASING AN AIR LOCK On some systems a message will appear on the display indica ng that the system is in PUMP PRIMING MODE. This mode will last for 4 to 5 minutes before automa cally entering the normal opera on mode. See complete details for your spa in sec on HYDROPOOL CONTROL SYSTEMS When the hot tub pump is located below water level, the water should start circula ng immediately. If the motor works but if you do not no ce water circula on within the first 15 seconds, the pump may require priming due to trapped air (referred to as an air lock’). To prime (inset 2), open the hose-bib to allow trapped air to escape. Close as soon as the water flow from the jets becomes regular. If the pumps have not primed a er 2 minutes, and water is not flowing from the jets, DO NOT allow the pumps to con nue to run. Turn power off at the main house panel (or GFCI) and try releasing the air again by loosening the union on the discharge side of the pump(s) while the motor is not running. Turn the power back on. If the pump(s) does not prime a er 15 seconds, some mes momentarily turning the pump(s) off and on will help the system to prime (note: do not do this more than 5 mes). Repeat if necessary. · Important: Under NO circumstances should the pump(s) be allowed to operate without priming beyond 5 minutes, as this may not only cause unwarrantable damage to the pump, it may also cause the control system to go into an overheat condi on. Defini on:Priming’ a pump is a term used to describe the process in which air trapped in the plumbing and pump wetend (referred to as an `air lock’) is released, allowing the pump to move water efficiently through the plumbing system and to the jets.
16

RELEASING AIR TRAPPED IN FILTER…
AIR VENT VALVE
· When the pump starts circula ng, it will be necessary to release trapped air in the filter. Carefully loosen the air vent valve counter-clockwise un l there is the hissing sound of air escaping. Once there is a steady stream of water, close the vent valve, ensuring that the o-ring does not become pinched.
· Turn the Hydrotherapy pump(s) on and re-check for leaks. The control system will automa cally return the pump(s) off a er 15 minutes.
· Adjust the hot tub heat control at the topside panel to the desired water temperature. · Adjust water balance (pH, TA, calcium hardness) to recommended levels and add sani zer
once the water temperature reaches 20oC (68oF). See sec on HOT TUB WATER BALANCE · Keep insulated safety hard cover on the hot tub, and the air controls closed during the en re heat up process. NOTE: In order to prevent damage to your pillows caused by the gassing effect of the chemicals, we do recommend to remove them when the spa is not in use. By removing them you will extend considerably the life length of your pillows. We do design ours pillows to be removed easily in order to make sure they will not remain in the spa when it’s not in use.
17

HYDROPOOL SELF CLEAN SERIES CONTROL SYSTEMS NORTH AMERICA / EUROPE GECKO IN.YE/YT SPA PACK

INITIAL START-UP
Before applying voltage to power-up your hot tub, it is very important that you understand the sequence of events that occur when the system is ac vated in order that the pump(s) can be primed efficiently and damage to the system can be avoided.
At ini al power-up, the system will show the following screen.

TEMPERATURE CONTROL FUNCTIONALITY AND ADJUSTMENT

A er you exit the programming mode your hot tub will automa cally heat to the factory preset default temperature of 38°C (100°F).

The keypad does store the date and me for a limited me so when the system starts up a er a loss of power it may be necessary to reprogram the
me and date if the power down dura on is greater than 48 hours.

The temperature shown in white on the screen is the current water temperature. Use the UP and DOWN icon to set the desired temperature.
The set point will appear in blue on the screen. A er 3 seconds without any change to the set temperature value, the keypad will resume the normal display of messages.

PROGRAMMING THE DATE AND TIME

When the set value is lower than the current temperature “Cooling to XX”F (“C)” will appear. When the value is set higher than the current temperature, “Hea ng to XX”F (“C)” will be indicated.

Here you can adjust the me format (AM/PM or 24h), day of the week and me. Use the icons to choose the se ng that you want to adjust and select it by scrolling through the menu.

18

HYDROPOOL SELF CLEAN SERIES CONTROL SYSTEMS GOLD SERIES CONTROLS

KEYPAD FUNCTIONS AND DISPLAY ICONS

SPA FUNCTION
KEY
SETTINGS FUNCTION
KEY
QUICK START / STOP KEY

PUMP 1 FUNCTION
KEY
BLOWER FUNCTION
KEY
LIGHT FUNCTION
KEY
TEMP UP KEY
TEMP DOWN
KEY

INVERT DISPLAY
KEY
DAY NIGHT CONTRAST
SLEEP MODE
KEY

19

HYDROPOOL SELF CLEAN SERIES CONTROL SYSTEMS PLATINUM SERIES CONTROLS

KEYPAD FUNCTIONS AND DISPLAY ICONS

SPA FUNCTION
KEY
SETTINGS FUNCTION
KEY
QUICK START / STOP KEY

PUMP 1 FUNCTION
KEY
PUMP 2 FUNCTION
KEY
BLOWER FUNCTION
KEY
LIGHT FUNCTION
KEY
TEMP UP KEY
TEMP DOWN
KEY

20

INVERT DISPLAY
KEY
DAY NIGHT CONTRAST
SLEEP MODE
KEY

HYDROPOOL SELF CLEAN SERIES CONTROL SYSTEMS TITANIUM SERIES CONTROLS

KEYPAD FUNCTIONS AND DISPLAY ICONS

SPA FUNCTION
KEY
SETTINGS FUNCTION
KEY
QUICK START / STOP KEY

PUMP 1 FUNCTION
KEY
PUMP 2 FUNCTION
KEY
PUMP 3 FUNCTION
KEY
BLOWER FUNCTION
KEY
LIGHT FUNCTION
KEY
TEMP UP KEY
TEMP DOWN
KEY 21

INVERT DISPLAY
KEY
DAY NIGHT CONTRAST
SLEEP MODE
KEY

PUMP 1 FUNCTION
Press this pad to ac vate the pump
1st press ­ low speed (icon rotates slow) 2nd press ­ high speed (icon rotates fast) 3rd press ­ turns off
PUMP AUTOMATIC TIME-OUT Low and High speed ­ 15 minutes
PUMP 2 & 3FUNCTION (if included)
Press this pad to ac vate the pump
1st press ­ high speed (icon rotates fast) 2nd press ­ turns off
PUMP AUTOMATIC TIME-OUT High speed ­ 15 minutes

WATER CARE
The Water Care sec on will help you set up your ideal filtra on and hea ng se ngs. Choose from Away, Beginner, Energy Savings, Super Energy Savings and Weekender, depending on your needs.
Use the Light key to choose your se ng. A checkmark will appear on the selected icon to confirm.
In Energy Savings mode, the set point will be reduced by 20oF (11°C), which means that the hea ng system will not be engaged unless the temperature falls to 20oF (11°C) below the spa’s set temperature.

LIGHT FUNCTION

Press this pad to ac vate the light

1st press: 2nd press: 3rd press: 4th press:

rota ng colours solid blue colour solid green colour solid red colour

Water Care Modes:

Note: Pressing the light key in intervals less than three seconds will scroll to the next colour. Once you have selected the colour another press will turn the light off.
LIGHT AUTOMATIC TIME-OUT Time out ­ 60 minutes
SETTINGS KEY
From the home page you can access the Se ngs, where you will find:
· Water Care · Maintenance · Day & Time · Keypad Se ngs · Miscellaneous · Electrical Configura on · About
Use the icon keys to scroll up and down in the list. To select an op on, press the text.
At any point you can press the Spa Func on icon to return to the home screen.

Away:
In this mode the spa will always be in economy; the set point will be reduced by 20oF (11°C) and the filtra on can be reduced.
Beginner:
The spa will never be in economy mode, and will run a normal 24 hours of filtra on a day.
Energy Savings:
The spa will be in economy mode during the peak hours of the day and resume normal mode on the weekend.
Super Energy Savings:
The spa will always be in economy mode during peak hours, every day of the week.
Weekender:
The spa will be in economy mode from Monday to Friday, and will run normally on the weekend.

22

MODIFYING SCHEDULES
To see and / or modify the Water Care category, use the Se ngs icon to open the selected Water Care menu.
Scroll through the menu to choose a schedule to modify (choice of economy and filtra on schedules).
You have several possibili es for the schedule (Mon-Fri, weekend, every day, or single days). The schedules will be repeated every week. The me and dura on are set in 30 minute increments. Once you have set the schedule, use Spa Func on Icon to go back. Ensure that you have selected the desired Water Care op on in the main Water Care menu.
The filtra on schedule shown on the screen will apply to the main filtra on pump. Your spa uses a circula on pump configured to run 24 hours by default and the screen will show you the purge se ng instead of filtra on. The purges are pre-programmed for a fixed number of minutes, therefore the dura on will be set to N/A on the screen, and only the start me can be modified.

FILTERING
Your spa is equipped with a circula on pump that filters your water for 24 hours a day. If the water temperature exceeds the set temperature by 4°F (and set point is 95°F or higher) then this pump will shut off automa cally un l the temperature drops below the set point by approximately 1.5°F.
You can bypass the pack filtra on overtemperature feature. When Warm weather is “Off”, the filtra on over-temperature is disabled. This feature allows the spa to con nue filtering even through the water temperature is high.
MAINTENANCE
From the Se ngs page you can access the Maintenance Menu, which gives you access to the following op ons:
· Maintenance reminders · Standby
Press the text to make a selec on.

23

MAINTENANCE REMINDERS

The in.k1000 keypad will remind you of maintenance required on your spa, like rinsing or cleaning the filter. Each task has its own dura on, based on normal use.

The Maintenance Reminders menu allows you

to verify the me le before maintenance is

required, as well as to reset the me once a

task is completed.

Scroll through the menu to move through the DATE AND TIME

list.

Here you can adjust the me format (AM/PM

or 24h), day of the week and me. Use the

icons to choose the se ng that you want to

adjust and select it by scrolling through the

menu.

STANDBY
The Standby mode allows you to service your spa. Pumps will stop for 30 minutes, and automa cally restart a er this me.
Once Standby mode has been ac vated a screen will appear to show the pumps are stopped. The normal spa page will return at the end of the maintenance.
Press Cancel to leave Standby mode and restart the spa.
NOTE: If the heater is ac vated it could take up to 20 minutes for the Standby Mode to be ac vated as it needs to finish its heat cycle. In order to avoid this you will need to drop the set temperature below the water temperature in order for the Standby Mode to be ac vated immediately.

24

KEYPAD SETTINGS

ELECTRICAL CONFIGURATION

In this sec on you can change the

Please do not make changes in this sec on

temperature unit and language. Use the

unless you are a qualified electrician.

arrow keys and move to the se ng that you

would like to change. Use the Light key to

ABOUT

choose and the arrow keys to modify

This sec on shows informa on about the

For the temperature se ng you have a choice keypad so ware number and the revision

between Fahrenheit or Celsius.

numbers of the different components of your

system.

For the language se ng you have a choice

between English and French.

PURGE CYCLES
The purge cycles are programmed to begin at the start of each filter cycle. Pump 2 ac vates for 1 minute, shuts off and then Pump 1 ac vates for 1 minute then shuts off.
SMART WINTER MODE
Smart Winter Mode protects your system from the cold by turning the pumps on several mes a day to prevent water from freezing in the pipes. The Smart Winter Mode indicator turns on when in this mode of opera on. If the temperature drops to 4oC (39oF) within the heater chamber, the system automa cally ac vates the pump to provide freeze protec on. The pump will operate un l the temperature reaches 5oC (41oF) before returning to normal system mode.
COOLING DOWN
A er hea ng the spa water to the desired set point, the heater is turned off, but the filtra on pump remains on for a certain amount of me to ensure adequate cooling of the hea ng element in order to prolong the useful life of the heater. “Cooling to XX”F (“C)” message will appear at the bo om of the screen.

25

OPTIONAL I-COMMAND 2 SYSTEM The Smart Phone App that is designed as a wireless hot tub control which allows you to pick the water care se ngs that fit your schedule. Adjust filtra on and temperature se ngs and create the ideal hot tub experience from inside your home. This op on is supported by your iPhone®, iPOD touch®, iPAD® (requires iOS 8.0 or later) and Android Device (requires Android 2.3.3 and up). I-Command 2 (In. touch 2) comes with a state-of-the-art app and 2 pre-paired radio frequency transmi ers: One being part of the spa system and the second one, being connected to the Home Internet router. Both RF transmi ers are pre-linked to one another, enabling an immediate and perfect communica on between user and the spa. 1. Installing the home transmi er The home transmi er is provided with an Ethernet cable and a power supply. The in. touch 2 home transmi er unit must be installed inside the house, connected to a router and powered by the provided wall transformer. A longer Ethernet cable may be used to bring the home transmi er closer to the spa.
Simply connect the Ethernet cable into the RJ45 port of the in. touch 2 home transmi er and in one of the available LAN ports on your router. To power up the home transmi er, plug the provided wall outlet charger to a 120V (North American model) or 220V (European model) household supply and connect the USB cable to the wall outlet and the home transmi er.
26

2. Installing the spa transmi er If you purchased a spa with in. touch 2 as a standard feature or as an op on, note that the spa transmi er will be pre- installed. To ensure proper signal transmission, it may be necessary to change the posi on of the transmi er once the spa is installed in the yard. The transmi er should be located on the side of the spa facing the house.
The in. touch 2 spa transmi er must be installed under the spa skirt, at least 12″ (30 cm) away from any metal component or structure, as close as possible to the house to op mize the signal strength. Simply connect the spa transmi er into an available CO port of the spa control system (or any other accessory with a free CO port, such as the in. stream 2 audio amplifier, or the in. clear water sani za on system). 3. Pairing the home and spa transmi ers If you bought an in. touch 2 equipped spa or a complete retrofit kit, both transmi ers of your in. touch 2 will be factory pre-paired.
27

If you need to replace a transmi er or pair your transmi ers again, power up the home transmi er and press on its pairing bu on with a paper clip. The status light of the transmi er will blink yellow. Then, shut off the spa’s breaker to turn the spa transmi er off. Wait a li le and put the breaker back on. Within a few seconds, pairing will be completed and both transmi er status lights will turn to blue. 4. Transmi ers status LED indicator Both the home and spa transmi ers have color status LED that can be used for troubleshoo ng purposes .
When the LED status is blinking (blue, green or red) this indicates that the communica on between the EN module and the CO module it not established.
28

5. Strong and Long Range Communica on Signal Through their proprietary RF technology, in. touch 2 transmi ers emit a strong, stable and long-range signal between your spa and your router (about 3 mes longer than regular signal). No need for repeaters or boosters: your spa will always remain within reach in typical backyard se ngs.
6. Applica on
Download applica on:
The in. touch app allows you to control your spa using your home network or an Internet connec on anywhere in the world. The in. touch 2 app is wai ng for you in the App Store for iOS devices and on Google Play for Android — search for « in. touch 2 » then click on it to install.
29

USING THE APP
On your home network It is possible to access your spa with the in. touch 2 app through your home network. To be able to see your in. touch 2 in the applica on you need to connect your device to the same router (Wi-Fi network) than the one used to connect your Home Transmi er Go to the Wi-Fi se ngs sec on of your mobile device and choose the same network that your spa is connected to (i.e. Home). Once you’ve selected it, wait un l your device confirms the connec on. On the Internet The in. touch 2 allows you to use the Internet to control your spa from anywhere in the world. In order for them to communicate, both the in. touch 2 module and your device must be connected to a network that allows access to the Internet. Once your Home Transmi er is connected to the Internet (the LED status is blue), you can use your in. touch 2 app any me your device is also connected to the Internet (wireless or cellular network), even if you are away from home. To have access to your spa away from home, you will need to have previously linked your mobile device to your spa on your home network.
30

Setup your Wi-Fi on your device Before using your applica on, go to the Wi-Fi sec on of your device’s se ngs. Make sure you are connected to your home network. This needs to be the same Wi-Fi provided by the router to which you connected your Home Transmi er.
31

Find the icon for the in. touch 2 applica on, then tap on it to open it.
The first me you use the applica on a message will ask you: “in. touch 2” Would like to send you no fica ons. If you choose Allow, the applica on will send you no fica ons about the status of your spa. If you choose Don’t Allow, the applica on will not send you no fica ons.
32

Login page Before using your applica on, you must create an account first and then, you’ll be able to sign in. Your account will give you the opportunity to have access to your spa from any in. touch 2 applica on.
33

New account crea on When you choose to create a new account, you agree at the same me the Terms of Service and the Privacy Policy. You can read them at any me through this link: h ps://geckointouch.com/legal
34

Choose a spa This page displays all the spas detected by your applica on. To detect your spa, you need to connect your mobile device to the same network to which you connected your Home Transmi er. Once you have done a connec on with the spa its name will be saved on this page to allow you to connect to this spa from anywhere. To add a spa later on, go to Se ngs (up right corner) – Add a spa
35

Home page The main screen gives you access to your accessories, water temperature, water care and se ngs.
The app is mirroring the top side control (keypad) over the internet.
36

STANDBY MODE
A press of the SETTINGS icon and scroll to the MAINTENANCE menu op ons. Press the MAINTENANCE icon to display the STANDBY icon. Press the STANDBY icon and the following message will appear. “All pumps off! Press Cancel to exit Standby mode or Drain to drain spa” This mode allows you to stop all outputs including all automa c func ons such as a filter cycle, hea ng requests and smart winter mode purging for 30 minutes to perform quick spa maintenance.
DRAIN MODE
If you wish to put your spa into “DRAIN MODE” follow the instruc ons above for pu ng the spa into “STANDBY MODE” and then press DRAIN on the display. Once you do that the display will indicate “Drain in progress”. The filtra on pump will turn on and run for 60 minutes. In order to exit this mode, press CANCEL to exit DRAIN MODE. This will put you back into STANDBY MODE and if you wish to exit that press the same key to go back to the main screen.
HYDROTHER CONTROL AND WELLNESS THERAPY PACKAGE
This op onal feature allows you to select from eight different therapy packages to help soothe your aches and pains or focus on key parts of your body that need some a en on. In order to select the therapy you are looking for please reference the “Wellness Guide” that came with your hot tub and follow the instruc ons below.
PROGRAMMING THE HYDROTHER / WELLNESS THERAPY
From the main display page, press the WELLNESS icon to navigate into the submenu. From there you will see the first selec on page which offers your four op onal therapy packages (Leg Pain, Back Pain, Diet Ac va on, Sport Recovery). If you wish to select one of these packages simply press the text descrip on you are looking for. If not, scroll through the menu to go to the second page which offers you another four op onal therapy package (Headache Relief, Insomnia Relief, Stress Relief, Tonic Awakening). Press the text descrip on you are looking for.
37

TOPSIDE PANEL DISPLAY MESSAGES

Hr – An internal hardware error has been detected

Prr –

The Prr error message indicates a problem with the regula on probe. The system is constantly verifying if the temperature probe reading is within its normal limits.

HL – The water temperature at the heater has reached 119oF (48oC). Do not enter spa water.

FLO – The system did not detect any water flow while the filtra on pump was running.

UPL – No low level configura on so ware has been downloaded into the system.

AOH OH –

The temperature inside the spa skirt is too high, causing the internal temperature in the spa pack to increase above the normal limits. The water temperature in the spa has reached 108oF (42oC). Do not enter spa water.

OPTIONAL VARIABLE AIR THERAPY SYSTEM CONTROL FUNCTIONS:

Press: Blower bu on on main control to ac vate system.

1. ON/OFF : 1st Press: The Blower starts at maximum Speed. LED: ON 2nd Press: The blower stops. LED: OFF
2. TO CONTROL SPEED: Press and hold: Speed goes up or down, LED: ON when pressing. Release pressure at the desired speed.
3. TO CONTROL PULSATION: 1stPress: Slow Pulsa on Cycle, LED: ON. 2nd Press: Quick Pulsa on Cycle, LED: Flashes. 3rd Press: Pulsa on Cycle OFF, LED: OFF.

1

2

3

38

HYDROCLEAR PUREWATER SYSTEM
HOW IT WORKS This system combines the benefits of both Ozone and UV-C creates hydroxyl radicals to burn off contaminants and dissolved solids within the water to significantly increase the clarity of the spa water. The UV-C rays also breakdown chloramines which are the main cause of respiratory, eye and skin irrita on typically associated with chlorine. Harmful/corrosive off gassing is also drama cally reduced through this process. MAINTENANCE AND SERVICE While opera ng, check regularly to see if bubbles are entering the spa. A er 10,000 hours the UV LED will begin flashing yellow indica ng its me to replace the UV-C lamp. Replace the check valve assembly annually to ensure con nued op mal performance from the Hydroclear Pure Water System. To replace the UV-C lamp or check valve please go to www.balboawatergroup.com/UVSani zer for the procedure on how to do this. IMPORTANT YOU MUST CONTINUE TO CHECK YOUR WATER CHEMISTRY REGULARLY AND SANITIZING CHEMICALS WILL BE NECESSARY TO TREAT THE WATER. CONSULT YOUR SPA PROFESSIONAL FOR FURTHER ADVICE.
39

HYDROCLEAR PUREWATER SYSTEM (con nued)
UV-C LAMP REPLACEMENT INSTRUCTIONS Important: It is mandatory that the UV-C lamp is replaced every 12 months to maintain op mum performance.

KEY 1 2 3 4 5
6

DESCRIPTION SCREW ENCLOSURE COVER ENCLOSURE GASKET BALLAST CONNECTOR UV-C LAMP CONNECTOR UV-C LAMP

NOTE: Your UV System unit may look different than shown in the picture
DANGER
· Turn the spa breaker to the OFF posi on. · Allow the UV-C lamp (6) to cool down prior to removing it from the UV system. · Never look at the lit UV-C lamp (6). This can cause severe eye damage or blindness.
INSTRUCTIONS:
1. Remove the UV system enclosure cover (2) by removing 4 Phillips screws (1). Keep the gasket (3) together with the enclosure cover (2) for later use.
2. Make sure to use latex glove when handling the UV-C lamp (6). 3. Slowly disconnect the old UV-C lamp connector (5) from the ballast connector (4). 4. Slowly remove the old UV-C lamp (6) from the UV unit. 5. Slide the new UV-C lamp (6) into the UV unit. 6. Reconnect the new UV-C lamp connector (5) to the ballast connector (4). Make sure the connectors mate
completely. Do not force. 7. Reinstall the enclosure cover (2) with the gasket (3) and secure with screws (1). 8. Reconnect the unit to the spa controller and reinstall the spa controller’s cover. 9. Turn on the power to the spa. 10. Once power is ac vated you can check the ballast to see if the unit is func oning. A solid green light indicates
the unit is being provided power and should always be on. A solid red light indicates that the UV-C lamp is ac vated.
WARNING
The UV-C lamp used in this unit contains mercury. Properly dispose of the old UV-C lamp in accordance with disposal laws. See www.lamprecycle.org.
40

HOT TUB WATER BALANCE ­ GENERAL OVERVIEW

NOTABLE POINTS

· The reliability and longevity of your hot tub support

equipment are directly related to how well water quality is

maintained!

· The small volume of water in your hot tub is easily affected

by the introduc on of oils, lo ons, perspira on and

chemicals. It is impera ve that you give your hot tub

regular a en on to maintain clean, and balanced water to

prevent premature damage and/or failure (corrosion/

calcifica on) to the support equipment.

Maintaining

proper hot tub water balance and sani zer levels is ex-

tremely important. Neglected hot water will allow bacteria

to quickly spread.

· The mineral content of hot tub water increases due to

water evapora on, sani zers and other chemicals. If the

mineral concentra on, par cularly calcium, becomes too

high, the minerals will literally “drop” or precipitate out of

the water and deposit on the hot tub walls, plumbing, jets,

in the filter and on the heater element.

· It is very important that pH be checked frequently and

maintained in the recommended range as indicated in the

chartWATER BALANCE SUMMARY FOR YOUR HOT TUB

· It is also very important that Total Alkalinity (the ability of

the water to resist a change in pH) be maintained in the

recommended range as indicated in the chart WATER

BALANCE SUMMARY FOR YOUR HOT TUB

· Although there may be two iden cal hot tub models right

next door to each other, the maintenance requirements

will be different, dependant on such factors as:

­ bather load

­ frequency of use/quan ty of bathers

­ different body chemistry

­ sun vs. shade

­ temperature

For these reasons, it is very important to develop proper hot tub water maintenance habits and follow your Hydropool retailer’s recommended water maintenance procedures.
Heater and other component failure due to improper water balance is not covered under warranty.

WARNING
CHEMICAL HANDLING SAFETY HINTS
· Never pre-mix chemicals with each other prior to adding to hot tub water.
· Add only one chemical to the water at a me. · Always add chemicals to water and not vice-versa. · Chemicals may be corrosive, so handle with care and
store in a cool dark place. · Never smoke near chemicals as most are flammable · Ensure any spilled chemicals are carefully cleaned up
immediately. · Always have the POISON CONTROL telephone number
handy in the event of an emergency. · Keep chemicals out of children`s reach · Wear safety glasses and gloves when handling
chemicals.
INITIAL WATER FILL & BALANCE 1. Make sure the hot tub water is circula ng. 2. Add a sequesterant (stain and scale controller). Allow
water to circulate for an hour before adding anything else to the hot tub water. 3. Add a Shock / oxidizing agent . 4. Add sani zing tablets (Bromine or Chlorine) to the dispenser:
Your Hydropool hot tub comes with a built in bromine/ chlorine dispenser, (located in the lid of the cartridge filter housing), refer to sec on CARTRIDGE FILTER for details on removing and re-installing the lid. Once the filter lid is removed, you’ll no ce a clear 2.5 cm (1″) diameter tube extending from the bo om of the lid.
DISPENSER

Expose the large Refill hole at the end of the tube and add 5 or 6 tablets. Do not overfill dispenser as performance will be affected. Turn to expose the largest area and allow water to circulate for 3 or 4 hours before tes ng level. Adjust to lesser area as necessary to maintain a level of 2 ­4 PPM Sani zer.
Floa ng dispenser: As above, add 6 or 7 tablets, adjust ini ally to `5′, allow water to circulate for 3 to 4 hours, then test.
The tablets will dissolve slowly over a 10-14 day period, depending on se ng, and use of the hot tub.
5 Test pH and Total Alkalinity and also adjust accordingly. Expose the large Refill hole at the end of the tube and add 5 or 6 tablets. Do not overfill dispenser as performance will be affected. Turn to expose the largest area and allow water to circulate for 3 to 4 hours before tes ng level. Adjust to lesser area as necessary to maintain a level of 2-4 PPM Sani zer.
41

GLOSSARY OF COMMON WATER MAINTENANCE TERMS
1. CHLORINE ­ in granular, liquid or puck/tablet form, is an oxidant and biocidal agent. It is very effec ve and fast ac ng. Recommended chlorine residual level is 3.0 to 5.0 ppm.
2. CHLORAMINES ­ a compound formed when chlorine combines with nitrogen or ammonia present in the water. When allowed to go unchecked, it causes eye and skin irrita on and is indicated by a strong chlorine odor.
3. ONE-PART BROMINE ­ also available in puck/tablet form, is another type of oxidant/biocidal agent, and is introduced into the hot tub water via a brominator. Recommended bromine residual level is 3.0 to 5.0 ppm
4. TWO-PART BROMINE ­ composed of a liquid or powder component introduced manually into the water on a weekly basis, and a granular component that is added daily or as the hot tub is used.
5. BROMAMINES ­ are formed when bromine destroys nitrogen-bearing organic ma er. Unlike chloramines, bromamines don’t cause eye irrita on, however, when allowed to go unchecked, will cause an objec onable odour.
6. SHOCK ­ the prac ce of adding an oxidizing agent to hot tub water to destroy ammonia, nitrogenous and organic contaminants (chloramines and bromamines)
7. pH ­ a logarithmic value expressing the rela ve acidity or basicity of a substance (such as hot tub water) as indicated by the hydrogen ion concentra on. pH is expressed as a number on a scale of 0 to 14, where 0 is most acidic, 1 to 7 being acidic, 7 considered neutral, 7 to 14 being basic, and 14 being most basic. The ideal range for hot tub water is 7.4 to 7.6 ppm
8. pH INCREASER ­ raises the pH level of the water.
9. pH DECREASER ­ lowers the pH level of the water.
10. TOTAL ALKALINITY (TA) ­ the amount of carbonate, bicarbonate and hydroxide compounds present in the water that determines the ability or capacity of the water to resist change in pH. Also known as the buffering’ capacity. 11\. ALKALINITY BOOSTER ­ raises the alkalinity. 12\. CALCIUM HARDNESS ­ the calcium por on of the total alkalinity which represents 70 to 75% of total hardness. Calcium concentra ons determine whether water isso ‘ – too li le calcium, or hard’ -too much calcium. 13\. CALCIUM BOOSTER ­ increases the calcium level. 14\. TOTAL DISSOLVED SOLIDS (TDS) ­ a measure of the total amount of dissolved ma er in the water (calcium, carbonates, bicarbonates, magnesium, metallic compounds, etc.) 15\. SEQUESTERANTS (STAIN AND SCALE CONTROLLERS) ­ keeps dissolved metals and minerals in the water from a acking the hot tub shell and support equipment components. 16\. DEFOAMER ­ removes foam build-up from the water surface. At best, this is a temporary remedy, as excessive foam is merely a symptom of improper water balance (typically high organic residue and/or high pH). 17\. CARTRIDGE FILTER CLEANER ­ degreases and cleans cartridge filters. 18\. OZONATOR ­ generates Ozone (a gaseous molecule composed of 3 atoms of oxygen) and is injected into the hot tub water for the oxida on of water contaminants. 19\. TEST KIT ­ used to monitor specific chemical residual or demands in the water. May be in the form of litmus strips or liquid drops. 20\. PPM ­ abbrevia on forparts per million’, the unit of measurement used in chemical tes ng which indicates the parts by weight in rela on to one million parts by weight of water. Essen ally iden cal to the term mg/L – milligrams per liter.

WATER BALANCE SUMMARY FOR YOUR HOT TUB*

SANITIZER (ppm) Chlorine Bromine
CHEMICAL PH Total Alkalinity (TA)
Calcium Hardness

MIN

IDEAL

1.0

3.0 – 5.0

1.0

3.0 – 5.0

MAX 5.0 5.0

7.2

7.4 – 7.6

7.8

80

80 – 120

180

150

200 -400

500 -1000

*Na onal Spa & Pool Ins tute recommended levels for residen al spas/hot tubs 42

PROBLEM
Cloudy Water High Total Alkalinity High pH levels High Calcium Hardness Scale (White/Grayish Deposit) Skin Eye Irritation Excessive Foam
Corrosion/Etching Discoloured Water (Clear v. turbid water) Unstable pH pH resistant to changing

WATER BALANCE TROUBLESHOOTING

POSSIBLE CAUSES
Microscopic particles too small to filter out.

SOLUTIONS
Test and adjust all water balance elements and add flocculent* to cause the particles to combine together so they can be filtered out. Increase filter cycle time.
Test these water balance elements and adjust to recommended parameters.

High Calcium Hardness Improper pH and/or Total Alkalinity levels Buildup of body oils or cosmetics
Laundry detergent residual in swimwear

Test calcium hardness level and treat with sequesting agent or perform partial drain/ refill.
Test water balance and make the appropriate changes.
If no water line is present you can try using defoamer to break up the contaminants and then a clarifier* to help filter them away. If a water line is present the spa may need to be drained and cleaned. Either way, the filter should be thoroughly cleaned by soaking over night in bleach. An oil absorbing sponge can help in preventing this in the future. Increase filter cycle time.
Prevent by running an extra rinse cycle on washing machine or re-rinse well by hand

Excess organic contaminants

Some organic matter is prone to causing foamy water as it breaks down in the filter (maple leaves especially). Generally using defoamer to break up the contaminants, then a clarifier
To help filter them away followed by thoroughly cleaning your filter will clear up the problem. It may however be necessary to drain and refill your spa if the foaming is quite excessive.

Low Calcium Hardness
Presence of metals in water (iron, copper, etc)

Test calcium hardness and if necessary increase with calcium chloride
Test total alkalinity levels and if necessary increase with sodium bicarbonate

Presence of metals in water (iron, copper, etc) Low Total Alkalinity levels
High Total Alkalinity levels

Treat with chelating or sequestering agent
Test total alkalinity levels and if necessary increase with sodium bicarbonate
Test total alkalinity levels and if necessary decrease with sodium bisulfate or muriatic acid*

• Contact your local Hydropool retailer for specific product recommendation

43

ROUTINE HOT TUB MAINTENANCE
REVIEW CHEMICAL HANDLING SAFETY HINTS

DAILY 1 Test water, and if necessary, add shock. 2 Ensure proper water level is maintained.
WEEKLY 1 Test pH and Alkalinity. Adjust accordingly 2 Top-up chemical dispenser 3 Add sequesterant (stain and scale controller) 4 Remove and spray cartridge filter with garden hose and
re-install (see section CARTRIDGE FILTER) 5 Remove and clean out skimmer basket (see section
CLEANING THE SKIMMER BASKET) 6 Add Shock / oxidizing agent 7 Inspect union connections for o-ring and gasket leaks –
Tighten if loose
MONTHLY Soak your filter cartridge in a filter cartridge cleaning solution. Rinse thoroughly and, if possible, allow to dry before re-installing. Hydropool recommends purchasing a second filter so that while the first is cleaning, the other is clean and ready to install
QUARTERLY Drain hot tub at least once per quarter and clean the acrylic shell surface with a non-abrasive cleaner designed specifically for acrylic surfaces. See sections CHANGING THE HOT TUB WATER and DRAINING YOUR HOT TUB

CLEANING THE SKIMMER BASKET
1 Activate the STANDBY/DRAIN ASSIST mode 2 Remove the skimmer basket by pulling the weir door
forward, and pulling the basket up and towards the front 3 Remove debris from basket. (Note: Avoid hitting the
basket against objects to knock debris loose as this may damage the unit) 4 Reinsert basket 5 Take the system out of STANDBY/DRAIN ASSIST mode, and as the pump begins to operate, monitor water flow over the weir door to assure that it is free floating

NOTE: HYDROPOOL reserves the right to void the warranty of your spa if there is any indication of the use of products containing Hydrogen Peroxide.

SAFETY HARD COVER When a hot tub is uncovered, over 90% of heat is lost from the water surface. This evaporation also affects the chemical balance and could create humidity problems indoors. HYDROPOOL Safety Hard Covers are engineered for maximum thermal efficiency and appearance. They are hinged in the middle for easier handling, and the zip fastener allows the tapered foam inserts to be changed if damaged. The skirt of the safety hard cover hugs the lip of the hot tub for a tight fit. The locks, with one part fastened to the deck or skirt, prevent small children or animals from entering the hot tub. Do not drag the safety hard cover across the hot tub or decking. Standing on the hardcover could cause the tapered foam inserts to crack, which will lead to water absorption.
NEVER LEAN OR STAND ON YOUR HARDCOVER. The cover should be cleaned at least twice a year with a vinyl moisturizer and protector.
NOTE: ALWAYS ENSURE THE SAFETY HARDCOVER IS IN PLACE AND LOCKED WHENEVER THE HOT TUB IS NOT BEING USED. FAILURE TO DO SO MAY CAUSE DAMAGE OR CRACKING OF THE ACRYLIC SURFACE NOT COVERED UNDER THE WARRANTY.

44

CARTRIDGE FILTER The cartridge should be cleaned every two to four weeks,
depending on the amount of use. Signs that the filter requires
cleaning include: · Reduced jet power · Hazy gray water · Rattling noise in the pump or filter · Heater not working

LOCKING RING
AIR VENT VALVE
FILTER LID

REMOVAL 1 Activate the STANDBY/DRAIN ASSIST mode. 2 Remove the filter cover and open the small, black air vent /
bleeder valve on the top of the filter lid. 3 Lift the gray lock tab to disengage and turn the locking ring
counter clockwise. 4 Pull the filter lid upwards, and lift the cartridge elements
straight up and out of filter housing.
CLEANING
5 With a garden hose and spray nozzle, hose off the cartridge element, ensuring to carefully separate every pleat.
6 To remove collected lotions, body oils, etc. soak the cartridge in warm water and a filter cleaning/emulsifying compound (available at your HYDROPOOL retailer).
7 A cleaning cylinder may be purchased from your HYDROPOOL Hot tub Retailer.
8 Rinse thoroughly and dry before replacing. 9 Hydropool recommends purchasing a spare filter cartridge
so that you always have a clean substitute ready to rotate. 10 After the element has dried – if necessary, lightly brush
between pleats with a fine paint-brush to remove remaining dirt particles.

BUILT IN CHEMICAL DISPENSER
CARTRIDGE FILTER ELEMENT
FILTER HOUSING
CLEANING THE ACRYLIC SURFACE The acrylic surface can be cleaned and polished using a soft cloth and acrylic cleaner, available at your Hydropool retailer.

Do not use a wire brush or other devise to clean cartridge element. Do not put in dishwasher or washing machine.
RE-INSTALLATION 11 Place the cartridge filter back into the filter housing. 12 Replace the filter housing lid, pushing it down to seat,
ensuring that the lid o-ring does not become twisted. 13 Hydropool recommends that the lid o-ring be lubricated
with a non-petroleum based lubricant (i.e. Silicone gel) when it becomes dry. This will help to prevent twisting and pinching as the lid is installed, and significantly increase longevity of the o-ring. 14 Install the filter lock- ring, turning clockwise until the lock tab snaps into place. 15 Close the air vent/bleeder valve. 16 Take the system out of STANDBY/DRAIN ASSIST mode. 17 When the pump starts circulating on low speed, it will be necessary to release trapped air in the filter. Carefully loosen the air vent/bleeder valve counter-clockwise until there is the hissing sound of air escaping. Once there is a steady stream of water, close the vent valve, ensuring that the o-ring does not become pinched.

· Important: Do not use detergents the remaining residues will adversely affect water chemistry, making it difficult to maintain proper water balance · Do Not use abrasive cleaners ­ damage to the acrylic surface will occur.

45

CHANGING THE HOT TUB WATER A hot tub should be drained every 8-12 weeks, depending
on size and amount of use. If your hot tub is used daily or by
a large number of bathers, the water should be drained more often. One method to determine the approximate
length of time between water changes is to divide the water volume (in liters) of your hot tub by 13.5 and then divide by
the average number of bathers each day.

Formula

(___ ÷ 13.5 ) ÷ (____) = (____)

Volume of water in liters

Average daily bathers

Days between
water changes

EXAMPLE: 1000 liters divided by 13.5 divided by 2 = 37 days. The hot tub water must be changed when the amount of dissolved solids becomes excessive, and is usually indicated by “gray” or dull looking water.
DRAINING YOUR HOT TUB HYDROPOOL EXCLUSIVE QUICK-DRAINTM & FILL REFER TO DIAGRAM
OVERVIEW · Requires the use of 2 garden hoses – drain hose and fill hose · While first garden hose is draining old water from hot tub… ·…second hose is used to wash down interior surface of the hot tub and for fresh water fill.

11 To completely flush the old water from the plumbing lines: allow fresh water to fill into the foot-well area while the old water continues to be pumped out. Always keep at least 10cm (4 in.) of water in the foot-well so that pump 1 remains primed.
12 When the water from the drain hose turns clear (indicating fresh fill water), flush is complete.
13 Turn OFF the filtration pump. 14 Close the drain-hose bib on the hot tub plumbing line and
continue filling hot tub with fresh water. 15 Place cover on hot tub (to avoid splash-out). 16 Open filtration pump return gate valve. 17 Press the stop key and cancel to exit the drain mode on
the topside control panel (other than the pump 1 button) to take the system out of STANDBY/DRAIN ASSIST mode. Filtration pump and the heater will activate to circulate and heat the water while filling continues. This also reduces the possibility of an airlock occurring. 18 Continue adding fresh fill water until level is approximately 19mm (3/4 in.) from the top of the skimmer opening. 19 Once fill is complete, remove the #10 rubber expansion plug from the bottom of the skimmer housing. 20 If the filter housing was opened to replace the cartridge filter, it will be necessary to release trapped air from the filter housing by carefully loosening the small black air vent/bleeder valve located on the top of the filter housing. When water begins to escape close the air vent valve. 21 In the unlikely event of a pump air lock (pump 1 is operating but there is no water movement from the jets), refer to section PUMP PRIMING/RELEASING AN AIR LOCK
It may be necessary to put system into STANDBY/ DRAIN ASSIST mode in order to remove plug.

REFER TO FIGURE 1 & FIGURE 2 1 Locate nearest drain facility (Check your local bylaws). 2 Put the hot tub control system into STANDBY/DRAIN
ASSIST* mode. The system will automatically exit Standby Mode after 1 hour and resume normal operating functions. 3 Remove the skimmer basket so that the hole beneath it is accessible, and insert the #10 rubber expansion plug or plastic threaded plug provided. 4 Attach garden hose to hose bib located on plumbing line beside the hot tub control system. 5 Run garden hose to drain location. 6 Open hose bib. 7 Close filtration pump return gate valve next to the hose bib (this directs the water out the drain hose). 8 Activate the filtration pump. 9 Monitor the hot tub while it drains. 10 Use the second garden hose to wash down interior surface as the hot tub continues to drain. A sponge may also be used to wipe down the interior surface.

FIGURE 1

FIGURE 2

WATER SOFTENERS
Never fill a hot tub with water from a water softener, as it could adversely effect the water chemistry, making it difficult to maintain proper water balance. If you live in an area with hard or soft water, give careful attention to your Calcium Hardness level. Topping up with soft water is acceptable.

46

HYDROPOOL EXCLUSIVE QUICK-DRAINTM

FILTER CARTRIDGE CHEMICAL FEEDER

OZONATOR

FILL HOSE

DRAIN HOSE

FILTRATION PUMP

HEATER

FLOOR VACUUM

SKIMMER/PRE-FILTER

THE SELF-CLEANING MODE INDICATOR

This worry-free indicator is located on the topside control display. The display will indicate “Self Clean Mode” on the screen ensuring that the Self- Clean and Eco Heat Systems are both functioning and reassuring you of your family’s safety and protection.

47

PROTECTING YOUR CABINET EVERLAST FINISH
Some HYDROPOOL hot tub cabinets are made from Everlast synthetic plastic material. These cabinets utilize a magnetic latching system to fasten and hold the exterior panels in place. In order to remove a panel for access you need to start at the lower right hand corner of the panel and disengage the first magnetic latch by pulling the panel forward enough to allow your hand to get behind the panel. Once you have done that you can run your hand behind the panel to disengage the other magnetic latches and be able to remove the panel completely. To reinstall the panel, line the panel up in the opening and lift it in place and the magnetic latches will engage with the panel so you can shift it place and complete the reinstallation. HYDROPOOL spa Everlast Synthetic cabinets are made from a unique, non-porous all-weather plastic material and with proper care will maintain its beauty for many years. CLEANING Using hot soapy water and a stiff bristle brush, a soft cloth or sponge will remove surface dirt and grime. Stains can be removed with a water- based cleaner (E.g. Windex, Pledge, Simple Green, etc.). You can also use a power washer with a medium/ wide nozzle setting to clean the surface of the product. Cleaning every few months is recommended.
…CAUTION: Do not use cleaners containing aromatic solvents or harsh detergent /chemicals on Everlast” material. If dirt and surface contaminants are causing a dirty/brownish tint, an extra step can be taken. Use a 75% bleach and 25% water mixture and wipe the surfaces down. Allow the mixture to remain on the product for an hour, then rinse thoroughly. (Be sure to do this in a safe location and protect your eyes, skin, and wear old clothes). MAINTENANCE Your HYDROPOOL `Everlast’ cabinet is made from a next-generation outdoor premium synthetic material. If the material is damaged during use (scratched or chipped), it can often be repaired. Repairing Scratches — Take a very fine grade of steel wool (0000 grade) and “sand” the scratched area in the same direction that the embossing pattern runs. Apply enough pressure to gradually minimize the scratched area. Once the scratches are reduced, the surface area may appear dull and possibly even lighter in color; however, this will be less noticeable over time and with outdoor exposure. To finish the repair, apply liquid paste such as Finesse-it, furniture polish or carnauba wax and buff using auto paint repair buffing wheel to a finish.
48

WINTERIZING YOUR HYDROPOOL HOT TUB
In the event that you do not wish to use your hot tub year-round, it is very important that you properly winterize it to protect against damage from freezing. Your HYDROPOOL retailer can perform this service for a nominal fee. If you choose to winterize your hot tub yourself, please follow the direc ons outlined below:
1. Drain the hot tub en rely. See sec on – DRAINING YOUR HOT TUB. 2. Remove and clean the filter cartridge. See sec on – CARTRIDGE FILTER. 3. Remove all of the jet inserts that are removable, any suc on covers, water diverter cap(s) and waterfall
control valve cap(s). 4. Using a wet / dry u lity vacuum, remove remaining water from the jet openings, filter cartridge housing and
footwell. 5. Using the blower side of the vacuum, posi on the blower nozzle into the top of the water diverter cap to
blow out any water remaining in the plumbing lines so that the excess water will come out the jet bodies. 6. Replace all of the water diverter caps and and waterfall control valve caps ensuring all gaskets are in place. 7. At the equipment end, loosen one union from each pump so that any excess water in each pump can be
vacuumed out completely. 8. Either pour or use a turkey baster where necessary to add potable biodegradable RV an freeze to areas such
as pump wet ends, jet channels, filter housing and any blower channels. 9. Reinstall all jet inserts and all suc on covers.
DO NOT USE AUTOMOTIVE ANTIFREEZE.
· Important: mixing potable biodegradable RV an freeze with water significantly reduces its ability to protect against freezing. Therefore, it is very important ALL water is removed from the hot tub plumbing before adding. · Add potable RV an freeze to the holes in the bo om suc on/drain to prevent any trapped water in the false floor from freezing and damaging the hot tub shell. · Turn pump on for only a few seconds to circulate the an freeze. · Unthread and disconnect all unions in the support equipment area. Remove lowest winter drain plug on pump face plate. Repeat for all pumps, where applicable.
· Cover exposed plumbing connec ons with plas c bags and duct tape. · Where prac cal, disconnect hot tub support equipment and store in a dry heated area. · Install the safety hardcover, and cover the en re hot tub with a tarp to prevent premature weathering of
the cabinet and the safety hard cover. · Remove snow build up regularly to prevent damage to the safety hard cover. · It is assumed that your HYDROPOOL hot tub has been properly installed on a reinforced concrete pad to
eliminate li ing of the hot tub due to hydrosta c ground water pressure.
If you are not 100% confident that your hot tub is properly winterized, please consult your authorized HYDROPOOL Hot Tub Retailer. Caution recommends that an authorized Hydropool Retailer winterize your hot tub in the initial year. Damage as a result of freezing is not covered by the warranty.
DRAIN PLUG LOCATIONS 49

GENERAL TROUBLESHOOTING
WHAT TO DO IN THE EVENT OF POWER FLUCTUATIONS The power supply into your home is, for the most part, fairly consistent. However, when local power demand is high, there is a tendency for the voltage entering your home to drop (sometimes significantly) or fluctuate. This condition is referred to as a brown-out’. Although safeguards have been built into the system to protect against this condition, supply voltage may drop low enough, if even for a second, to cause the system to display aghost’ message. Should this occur or if the display shows partial messages, try resetting the system by turning power to the swim spa, waiting a few minutes, then turning power on again. If this does not reset the system, contact your local HYDROPOOL retailer or service organization. POWER FAILURE OR SYSTEM FAULT DURING COLD WEATHER CONDITIONS If your control system will not reset, (i.e. GFCI trips) or if your pump will not circulate for any other reason, place a low wattage space heater under the cabinet in the equipment area. This will delay the risk of freezing while a service appointment is scheduled.
Always follow the manufacturers instructions when locating and placing a portable electric space heater into service. Ensure that safe clearance to combustible surfaces is maintained. Do not leave unattended.
NOTES:
50

IN.YE-3 EU WIRING DIAGRAM

51

IN.YE-3 NA WIRING DIAGRAM

52

IN.YE-5 EU WIRING DIAGRAM

53

IN.YE-5 NA WIRING DIAGRAM

54

IN.YT-12 EU WIRING DIAGRAM

55

IN.YT-12 NA WIRING DIA-

56

References

• in.touch 2 Gecko Alliance in.touch 2
• Hydropool
• Lamp Recycle – Environmental Responsiblility Starts Here

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>