BULBRITE LED12REC 4 12 Watt 4 Inch Integrated LED Recessed Downlight Instructions
- June 14, 2024
- BULBRITE
Table of Contents
BULBRITE LED12REC 4 12 Watt 4 Inch Integrated LED Recessed Downlight
Models
LED9REC/4/927/WHRD/D&LED9REC/4/930/WHRD/D&LED9REC/4/940/WHRDD&LED9REC/4/927/WHRD-G/D &LED9REC/4/930/WHRD-G/D & LED12REC/4HL/827/WHRD/D & LED12REC/4HL/830/WHRD/D & LED12REC/4HL/840/WHRD/D
Important Information
Before installation, confirm all parts are in good condition. If any parts are damaged, do not attempt to install. Contact an American Lighting Association (ALA) Certified Relationship Specialist at Bulbrite for help with installation or questions about your kit at 800-528-5555 or infocalbulbrite.com.
Dimension
Safety instructions
These instructions are Provided for your safety. It is important that the instructions are read carefully and completely before assembling. Please save these instructions, as you may need them at a later date.
WARNING:
RISK OF FIRE OR ELECTRIC SHOCK. LED RETROFIT KIT INSTALLATION REQUIRES
KNOWLEDGE OF LUMINAIRES ELECTRICAL SYSTEMS. IF NOT QUALIFIED, DO NOT ATTEMPT
INSTALLATION. CONTACT A QUALIFIED ELECTRICIAN. BE SURE THE ELECTRICITY THE
FIXTURE YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE
CIRCUIT BREAKER IS TURNED OFF. TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT
EXPOSE WIRING TO EDGES OF SHEET METAL OR OTHER SHARP OBJECTS. DO NOT MAKE GR
ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OF ELECTRICAL COMPONENTS DURING
KIT INSTALLATION. THIS LED RETROFIT MUST BE INSTALLED IN ACCORDANCE WITH THE
NATIONAL ELECTRICAL CODE (NEC) AND RELEVANT LOCAL CODE. INSTALLERS SHOUD NOT
DISCONNECT EXISTING WIRES FROM LAMP HOLDER TERMINALS TO MAKE NEW CONNECTIONS
AT LAMP HOLDER TERMINALS. INSTEAD INSTALLERS SHOULD CUT EXISTING LAMP HOLDER
LEADS AWAY FROM THE LAMPHOLDER AND MAKE NEW ELECTRICAL CONNECTIONS TO
LAMPHOLDER LEAD WIRES BY EMPLOYING APPLICABLE CONNECTORS. INSTALL THIS KIT
ONLY IN LUMINAIRES THAT HAVE THE CONSTRUCTION FEATURES AND DIMENSIONS SHOW IN
THE PHOTOGRAPHS AND/OR DRAWINGS LOCATED IN THESE INSTRUCTIONS AND WHERE THE
INPUT RATING OF THE RETROFIT KIT DOES NOT EXCEED THE INPUT RATING OF THE
LUMINAIRE. SUITABLE FOR WET LOCATIONS. THIS DEVICE IS NOT INTENDED FOR USE
WITH EMERGENCY EXITS.
GENERAL INSTRUCTIONS
- This fixture operates on line voltage (standard household power) of 120 Volts, 60 Hertz.
- Minimum compatible recessed can dimensions: – 5.5″ can depth, 4″ can width (see diagram in Step 2).
- Can be used in wet locations.
- Suitable for Type IC or NON-IC installations.
- Operation temperature ranging between -20°C to +40°C (-4°F to +104°F). Lamp life may be affected outside these temperatures.
INSTALLATION INSTRUCTIONS
STEP 1
- Power off all electricity to the luminaire.
STEP 2
- This 4″ retrofit kit must be installed in a can with dimensions described within above diagram.
STEP 3
- Screw in the E26 quick connect adapter into the recessed can’s socket.
STEP 4
- Plug the female connector of the RETROFIT KIT onto the male connector of the QUICK CONNECT ADAPTER.
STEP 5
- Push the retrofit kit into the recessed can until the 3 clips fall securely into place. Ensure all wires are guided into the can before pushing up.
STEP 6
- Turn on all electricity to the luminaire and installation is complete.
Customers Support
145 WEST COMMERCIAL AVE, MOONACHIE NJ 07074 • T: 800 528 5555
www.bulbrite.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>